Rfc4744
TitleUsing the NETCONF Protocol over the Blocks Extensible Exchange Protocol (BEEP)
AuthorE. Lear, K. Crozier
DateDecember 2006
Format:TXT, HTML
Updated byRFC8996
Status:HISTORIC






Network Working Group                                            E. Lear
Request for Comments: 4744                                 Cisco Systems
Category: Standards Track                                     K. Crozier
                                                           December 2006


                    Using the NETCONF Protocol over
             the Blocks Extensible Exchange Protocol (BEEP)

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The IETF Trust (2006).

Abstract

   This document specifies an application protocol mapping for the
   Network Configuration Protocol (NETCONF) over the Blocks Extensible
   Exchange Protocol (BEEP).

Table of Contents

   1. Introduction ....................................................2
      1.1. Why BEEP? ..................................................2
   2. BEEP Transport Mapping ..........................................2
      2.1. NETCONF Session Establishment ..............................2
      2.2. Starting a Channel for NETCONF .............................4
      2.3. NETCONF Session Usage ......................................5
      2.4. NETCONF Session Teardown ...................................5
      2.5. BEEP Profile for NETCONF ...................................6
   3. Security Considerations .........................................6
   4. IANA Considerations .............................................7
   5. Acknowledgments .................................................7
   6. References ......................................................8
      6.1. Normative References .......................................8
      6.2. Informative References .....................................8








RFC 4744                   NETCONF over BEEP               December 2006


1.  Introduction

   The NETCONF protocol [1] defines a simple mechanism through which a
   network device can be managed.  NETCONF is designed to be usable over
   a variety of application protocols.  This document specifies an
   application protocol mapping for NETCONF over the Blocks Extensible
   Exchange Protocol (BEEP) [7].

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [2].

1.1.  Why BEEP?

   Use of BEEP is natural as an application protocol for transport of
   XML.  As a peer-to-peer protocol, BEEP provides an easy way to
   implement NETCONF, no matter which side of the connection was the
   initiator.  This "bidirectionality" allows for either manager or
   agent to initiate a connection.  This is particularly important to
   support large numbers of intermittently connected devices, as well as
   those devices that must reverse the management connection in the face
   of firewalls and network address translators (NATs).

   BEEP makes use of the Simple Authentication and Security Layer (SASL)
   [3].  The SASL profile used by BEEP allows for a simple and direct
   mapping to the existing security model for command line interface
   (CLI), while Transport Layer Security (TLS) [4] provides a strong,
   well-tested encryption mechanism with either server or server and
   client-side authentication.

2.  BEEP Transport Mapping

   All NETCONF over BEEP implementations MUST implement the profile and
   functional mapping between NETCONF and BEEP as described below.

   For purposes of this document, a manager is a NETCONF client, and an
   agent is a NETCONF server.  Use of client/server language in BEEP is
   avoided because of the common notion that in networking clients
   connect to servers.

2.1.  NETCONF Session Establishment

   Managers may be either BEEP listeners or initiators.  Similarly,
   agents may be either listeners or initiators.  To establish a
   connection, the initiator connects to the listener on TCP port 831.
   Thus, the initial exchange takes place without regard to whether a
   manager or the agent is the initiator.  After the transport
   connection is established, as greetings are exchanged, they SHOULD



RFC 4744                   NETCONF over BEEP               December 2006


   each announce their support for TLS and optionally SASL.  Once BEEP
   greeting messages are exchanged, if TLS is to be used and available
   by both parties, the listener STARTs a channel with the TLS profile.

   Once TLS has been started, a new BEEP greeting message is sent by
   both initiator and listener, as required by the BEEP RFC.

   After all BEEP greeting messages are exchanged in order for roles to
   be clear, the agent MUST advertise the NETCONF profile.  The manager
   MUST NOT advertise the NETCONF profile.  If the agent side of the
   communication (either initiator or listener) receives a BEEP
   <greeting> element that contains the NETCONF profile, it MUST close
   the connection.  Similarly, if neither side issues a NETCONF profile
   it is equally an error, and the listener MUST close the connection.

   At this point, if SASL is desired, the initiator starts a BEEP
   channel to perform a SASL exchange to authenticate itself.  Upon
   completion of authentication the channel is closed.  That is, the
   channel is exclusively used to authenticate.

   Examples of both TLS and SASL profiles can be found in [7].

   It is anticipated that the SASL PLAIN mechanism will be heavily used
   in conjunction with TLS [5].  In such cases, in accordance with RFC
   2595 the PLAIN mechanism MUST NOT be advertised in the first BEEP
   <greeting>, but only in the one following a successful TLS
   negotiation.  This applies only if TLS and SASL PLAIN mechanisms are
   both to be used.  To avoid risk of eavesdropping, the SASL PLAIN
   mechanism MUST NOT be used over unencrypted channels.  More specifics
   about the use of SASL and TLS are mentioned in Security
   Considerations below.

   Once authentication has occurred, there is no need to distinguish
   between initiator and listener.  We now distinguish between manager
   and agent, and it is assumed that each knows its role in the
   conversation.















RFC 4744                   NETCONF over BEEP               December 2006


2.2.  Starting a Channel for NETCONF

   The manager now establishes a new channel and specifies the single
   NETCONF profile.  For example:

         (M = Manager; A = Agent)

         M: MSG 0 1 . 10 48 118
         M: Content-type: application/beep+xml
         M:
         M: <start number="1">
         M:   <profile uri="http://iana.org/beep/netconf" />
         M: </start>
         M: END
         A: RPY 0 1 . 38 87
         A: Content-Type: application/beep+xml
         A:
         A: <profile uri="http://iana.org/beep/netconf" />
         A: END

   At this point, we are ready to proceed on BEEP channel 1 with NETCONF
   operations.

   NETCONF messages are transmitted with a Content-type header set to
   "text/xml".

   Next the manager and the agent exchange NETCONF <hello> elements on
   the new channel so that each side learns the other's capabilities.
   This occurs through a MSG.  Each side will then respond positively.
   The following example is adapted from [1] Section 8.1:


       A: MSG 1 0 . 0 457
       A: Content-type: application/beep+xml
       A:
       A: <?xml version='1.0' encoding="UTF-8"?>
       A: <hello xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
       A:   <capabilities>
       A:     <capability>
       A:       urn:ietf:params:netconf:base:1.0
       A:     </capability>
       A:     <capability>
       A:       urn:ietf:params:netconf:capability:startup:1.0
       A:     </capability>
       A:     <capability>
       A:       http://example.net/router/2.3/core#myfeature
       A:     </capability>
       A:   </capabilities>



RFC 4744                   NETCONF over BEEP               December 2006


       A:   <session-id>4</session-id>
       A: </hello>
       A: END

       M: RPY 1 0 . 0 0
       M: END

   Future NETCONF capabilities may require additional BEEP channels.
   When such capabilities are defined, a BEEP mapping must be defined as
   well.

   At this point, the NETCONF session is established, and capabilities
   have been exchanged.

2.3.  NETCONF Session Usage

   Nearly all NETCONF operations are executed through the <rpc> element.
   To issue a remote procedure call (RPC), the manager transmits on the
   operational channel a BEEP MSG containing the RPC and its arguments.
   In accordance with the BEEP standard, RPC requests may be split
   across multiple BEEP frames.

   Once received and processed, the agent responds with BEEP RPY
   messages on the same channel with the response to the RPC.  In
   accordance with the BEEP standard, responses may be split across
   multiple BEEP frames.

2.4.  NETCONF Session Teardown

   Upon receipt of <close-session> from the manager, once the agent has
   completed all RPCs, it will close BEEP channel 0.  When an agent
   needs to initiate a close, it will do so by closing BEEP channel 0.
   Although not required to do so, the agent should allow for a
   reasonable period for a manager to release an existing lock prior to
   initiating a close.  Once the agent has closed channel 0, all locks
   are released, and each side follows teardown procedures as specified
   in [8].  Having received a BEEP close or having sent <close-session>,
   a manager MUST NOT send further requests.  If there are additional
   activities due to expanded capabilities, they MUST cease in an
   orderly manner and should be properly described in the capability
   mapping.










RFC 4744                   NETCONF over BEEP               December 2006


2.5.  BEEP Profile for NETCONF

   Profile Identification: http://iana.org/beep/netconf

   Messages exchanged during Channel Creation: not applicable

   Messages starting one-to-one exchanges: "hello", "rpc", "rpc-reply"

   Messages in positive replies: "rpc-reply"

   Messages in negative replies: "rpc-reply"

   Messages in one-to-many exchanges: none

   Message syntax: [1]

   Message semantics: [1]

   Contact Information: See the "Author's Address" section of this memo.

3.  Security Considerations

   Configuration information is by its very nature sensitive.  Its
   transmission in the clear and without integrity checking leaves
   devices open to classic so-called "person-in-the-middle" attacks.
   Configuration information often times contains passwords, user names,
   service descriptions, and topological information, all of which are
   sensitive.  A NETCONF application protocol, therefore, must minimally
   support options for both confidentiality and authentication.

   The BEEP mapping described in this document addresses both
   confidentiality and authentication in a flexible manner through the
   use of TLS and SASL profiles.  Confidentiality is provided via the
   TLS profile and is used as discussed above.  In addition, the server
   certificate shall serve as the server's authentication to the client.
   The client MUST be prepared to recognize and validate a server
   certificate and SHOULD by default reject invalid certificates.

   In order to validate a certificate, the client must be able to access
   a trust anchor.  While such validation methods are beyond the scope
   of this document, they will depend on the type of device and
   circumstance.  Both the implementor and the administrator are
   cautioned to be aware of any circular dependencies that various
   methods may introduce.  For instance, Online Certificate Status
   Protocol (OCSP) servers may not be available in a network cold-start
   scenario and would be ill-advised for core routers to depend on to
   receive configuration at boot.




RFC 4744                   NETCONF over BEEP               December 2006


   For client-side authentication, there are several options.  The
   client MAY provide a certificate during the initiation phase of TLS,
   in which case the subject of that certificate shall be considered
   principle for authentication purposes.  Once again, server
   implementors should be aware of any interdependencies that could be
   created through protocols used to validate trust anchors.

   TLS endpoints may be authorized based on subject name or certificate
   authority (CA), depending on circumstances.  For instance, it would
   be unwise for a core Internet router to allow a netconf agent
   connection simply based on a valid certificate signed by a common CA,
   but not unreasonable to allow a connection from an agent with a
   particular distinguished name.  On the other hand, it might be
   desirable for enterprises to trust certificates signed by CAs of
   their network operations team.

   In the case where the client has not authenticated through TLS, the
   server SHOULD advertise one or more SASL profiles, from which the
   client will choose.  In the singular case where TLS is established,
   the minimum profile MAY be PLAIN.  Otherwise, implementations MUST
   support the DIGEST-MD5 profile as described in [6], and they MAY
   support other profiles such as the One-Time Password (OTP) mechanism
   [10].

   Different environments may well allow different rights prior to and
   then after authentication.  An authorization model is not specified
   in this document.  When an operation is not properly authorized, then
   a simple rpc-error containing "permission denied" is sufficient.
   Note that authorization information may be exchanged in the form of
   configuration information, which is all the more reason to ensure the
   security of the connection.

4.  IANA Considerations

   IANA assigned TCP port (831) for NETCONF over BEEP.

5.  Acknowledgments

   This work is the product of the NETCONF IETF working group, and many
   people have contributed to the NETCONF discussion.  Most notably, Rob
   Ens, Phil Schafer, Andy Bierman, Wes Hardiger, Ted Goddard, and
   Margaret Wasserman all contributed in some fashion to this work,
   which was originally to be found in the NETCONF base protocol
   specification.  Thanks also to Weijing Chen, Keith Allen, Juergen
   Schoenwaelder, Marshall Rose, and Eamon O'Tuathail for their very
   constructive participation.  The authors would also like to thank
   Elwyn Davies for his constructive review.




RFC 4744                   NETCONF over BEEP               December 2006


6.  References

6.1.  Normative References

   [1]  Enns, R., Ed., "NETCONF Configuration Protocol", RFC 4741,
        December 2006.

   [2]  Bradner, S., "Key words for use in RFCs to Indicate Requirement
        Levels", BCP 14, RFC 2119, March 1997.

   [3]  Melnikov, A. and K. Zeilenga, "Simple Authentication and
        Security Layer (SASL)", RFC 4422, June 2006.

   [4]  Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS)
        Protocol Version 1.1", RFC 4346, April 2006.

   [5]  Newman, C., "Using TLS with IMAP, POP3 and ACAP", RFC 2595,
        June 1999.

   [6]  Leach, P. and C. Newman, "Using Digest Authentication as a SASL
        Mechanism", RFC 2831, May 2000.

   [7]  Rose, M., "The Blocks Extensible Exchange Protocol Core",
        RFC 3080, March 2001.

   [8]  Rose, M., "Mapping the BEEP Core onto TCP", RFC 3081,
        March 2001.

6.2.  Informative References

   [9]   Sperberg-McQueen, C., Paoli, J., Maler, E., and T. Bray,
         "Extensible Markup Language (XML) 1.0 (Second Edition)", World
         Wide Web Consortium, First Edition,
         http://www.w3.org/TR/2000/REC-xml-20001006, October 2000.

   [10]  Newman, C., "The One-Time-Password SASL Mechanism", RFC 2444,
         October 1998.














RFC 4744                   NETCONF over BEEP               December 2006


Authors' Addresses

   Eliot Lear
   Cisco Systems
   Glatt-com
   CH-8301 Glattzentrum, Zurich
   CH

   EMail: lear@cisco.com


   Ken Crozier

   EMail: ken.crozier@gmail.com





































RFC 4744                   NETCONF over BEEP               December 2006


Full Copyright Statement

   Copyright (C) The IETF Trust (2006).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST,
   AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES,
   EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT
   THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY
   IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
   PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.