Rfc9522
TitleOverview and Principles of Internet Traffic Engineering
AuthorA. Farrel, Ed.
DateJanuary 2024
Format:HTML, TXT, PDF, XML
ObsoletesRFC3272
Status:INFORMATIONAL





Internet Engineering Task Force (IETF)                    A. Farrel, Ed.
Request for Comments: 9522                            Old Dog Consulting
Obsoletes: 3272                                             January 2024
Category: Informational                                                 
ISSN: 2070-1721


        Overview and Principles of Internet Traffic Engineering

Abstract

   This document describes the principles of traffic engineering (TE) in
   the Internet.  The document is intended to promote better
   understanding of the issues surrounding traffic engineering in IP
   networks and the networks that support IP networking and to provide a
   common basis for the development of traffic-engineering capabilities
   for the Internet.  The principles, architectures, and methodologies
   for performance evaluation and performance optimization of
   operational networks are also discussed.

   This work was first published as RFC 3272 in May 2002.  This document
   obsoletes RFC 3272 by making a complete update to bring the text in
   line with best current practices for Internet traffic engineering and
   to include references to the latest relevant work in the IETF.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Not all documents
   approved by the IESG are candidates for any level of Internet
   Standard; see Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc9522.

Copyright Notice

   Copyright (c) 2024 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Revised BSD License text as described in Section 4.e of the
   Trust Legal Provisions and are provided without warranty as described
   in the Revised BSD License.

Table of Contents

   1.  Introduction
     1.1.  What is Internet Traffic Engineering?
     1.2.  Components of Traffic Engineering
     1.3.  Scope
     1.4.  Terminology
   2.  Background
     2.1.  Context of Internet Traffic Engineering
     2.2.  Network Domain Context
     2.3.  Problem Context
       2.3.1.  Congestion and Its Ramifications
     2.4.  Solution Context
       2.4.1.  Combating the Congestion Problem
     2.5.  Implementation and Operational Context
   3.  Traffic-Engineering Process Models
     3.1.  Components of the Traffic-Engineering Process Model
   4.  Taxonomy of Traffic-Engineering Systems
     4.1.  Time-Dependent versus State-Dependent versus
           Event-Dependent
     4.2.  Offline versus Online
     4.3.  Centralized versus Distributed
       4.3.1.  Hybrid Systems
       4.3.2.  Considerations for Software-Defined Networking
     4.4.  Local versus Global
     4.5.  Prescriptive versus Descriptive
       4.5.1.  Intent-Based Networking
     4.6.  Open-Loop versus Closed-Loop
     4.7.  Tactical versus Strategic
   5.  Review of TE Techniques
     5.1.  Overview of IETF Projects Related to Traffic Engineering
       5.1.1.  IETF TE Mechanisms
       5.1.2.  IETF Approaches Relying on TE Mechanisms
       5.1.3.  IETF Techniques Used by TE Mechanisms
     5.2.  Content Distribution
   6.  Recommendations for Internet Traffic Engineering
     6.1.  Generic Non-functional Recommendations
     6.2.  Routing Recommendations
     6.3.  Traffic Mapping Recommendations
     6.4.  Measurement Recommendations
     6.5.  Policing, Planning, and Access Control
     6.6.  Network Survivability
       6.6.1.  Survivability in MPLS-Based Networks
       6.6.2.  Protection Options
     6.7.  Multi-Layer Traffic Engineering
     6.8.  Traffic Engineering in Diffserv Environments
     6.9.  Network Controllability
   7.  Inter-Domain Considerations
   8.  Overview of Contemporary TE Practices in Operational IP
           Networks
   9.  Security Considerations
   10. IANA Considerations
   11. Informative References
   Appendix A.  Summary of Changes since RFC 3272
     A.1.  RFC 3272
     A.2.  This Document
   Acknowledgments
   Contributors
   Author's Address

1.  Introduction

   This document describes the principles of Internet traffic
   engineering (TE).  The objective of the document is to articulate the
   general issues and principles for Internet TE and, where appropriate,
   to provide recommendations, guidelines, and options for the
   development of preplanned (offline) and dynamic (online) Internet TE
   capabilities and support systems.

   Even though Internet TE is most effective when applied end-to-end,
   the focus of this document is TE within a given domain (such as an
   Autonomous System (AS)).  However, because a preponderance of
   Internet traffic tends to originate in one AS and terminate in
   another, this document also provides an overview of aspects
   pertaining to inter-domain TE.

   This document provides terminology and a taxonomy for describing and
   understanding common Internet TE concepts.

   This work was first published as [RFC3272] in May 2002.  This
   document obsoletes [RFC3272] by making a complete update to bring the
   text in line with best current practices for Internet TE and to
   include references to the latest relevant work in the IETF.  It is
   worth noting around three-fifths of the RFCs referenced in this
   document postdate the publication of [RFC3272].  Appendix A provides
   a summary of changes between [RFC3272] and this document.

1.1.  What is Internet Traffic Engineering?

   One of the most significant functions performed in the Internet is
   the routing and forwarding of traffic from ingress nodes to egress
   nodes.  Therefore, one of the most distinctive functions performed by
   Internet traffic engineering is the control and optimization of these
   routing and forwarding functions, to steer traffic through the
   network.

   Internet traffic engineering is defined as that aspect of Internet
   network engineering dealing with the issues of performance evaluation
   and performance optimization of operational IP networks.  Traffic
   engineering encompasses the application of technology and scientific
   principles to the measurement, characterization, modeling, and
   control of Internet traffic [RFC2702] [AWD2].

   It is the performance of the network as seen by end users of network
   services that is paramount.  The characteristics visible to end users
   are the emergent properties of the network, which are the
   characteristics of the network when viewed as a whole.  A central
   goal of the service provider, therefore, is to enhance the emergent
   properties of the network while taking economic considerations into
   account.  This is accomplished by addressing traffic-oriented
   performance requirements while utilizing network resources without
   excessive waste and in a reliable way.  Traffic-oriented performance
   measures include delay, delay variation, packet loss, and throughput.

   Internet TE responds to network events (such as link or node
   failures, reported or predicted network congestion, planned
   maintenance, service degradation, planned changes in the traffic
   matrix, etc.).  Aspects of capacity management respond at intervals
   ranging from days to years.  Routing control functions operate at
   intervals ranging from milliseconds to days.  Packet-level processing
   functions operate at very fine levels of temporal resolution (up to
   milliseconds) while reacting to statistical measures of the real-time
   behavior of traffic.

   Thus, the optimization aspects of TE can be viewed from a control
   perspective and can be both proactive and reactive.  In the proactive
   case, the TE control system takes preventive action to protect
   against predicted unfavorable future network states, for example, by
   engineering backup paths.  It may also take action that will lead to
   a more desirable future network state.  In the reactive case, the
   control system responds to correct issues and adapt to network
   events, such as routing after failure.

   Another important objective of Internet TE is to facilitate reliable
   network operations [RFC2702].  Reliable network operations can be
   facilitated by providing mechanisms that enhance network integrity
   and by embracing policies emphasizing network survivability.  This
   reduces the vulnerability of services to outages arising from errors,
   faults, and failures occurring within the network infrastructure.

   The optimization aspects of TE can be achieved through capacity
   management and traffic management.  In this document, capacity
   management includes capacity planning, routing control, and resource
   management.  Network resources of particular interest include link
   bandwidth, buffer space, and computational resources.  In this
   document, traffic management includes:

   1.  Nodal traffic control functions, such as traffic conditioning,
       queue management, and scheduling.

   2.  Other functions that regulate the flow of traffic through the
       network or that arbitrate access to network resources between
       different packets or between different traffic flows.

   One major challenge of Internet TE is the realization of automated
   control capabilities that adapt quickly and cost-effectively to
   significant changes in network state, while still maintaining
   stability of the network.  Performance evaluation can assess the
   effectiveness of TE methods, and the results of this evaluation can
   be used to identify existing problems, guide network reoptimization,
   and aid in the prediction of potential future problems.  However,
   this process can also be time-consuming and may not be suitable to
   act on short-lived changes in the network.

   Performance evaluation can be achieved in many different ways.  The
   most notable techniques include analytic methods, simulation, and
   empirical methods based on measurements.

   Traffic engineering comes in two flavors:

   *  A background process that constantly monitors traffic and network
      conditions and optimizes the use of resources to improve
      performance.

   *  A form of a pre-planned traffic distribution that is considered
      optimal.

   In the latter case, any deviation from the optimum distribution
   (e.g., caused by a fiber cut) is reverted upon repair without further
   optimization.  However, this form of TE relies upon the notion that
   the planned state of the network is optimal.  Hence, there are two
   levels of TE in such a mode:

   *  The TE-planning task to enable optimum traffic distribution.

   *  The routing and forwarding tasks that keep traffic flows attached
      to the pre-planned distribution.

   As a general rule, TE concepts and mechanisms must be sufficiently
   specific and well-defined to address known requirements but
   simultaneously flexible and extensible to accommodate unforeseen
   future demands (see Section 6.1).

1.2.  Components of Traffic Engineering

   As mentioned in Section 1.1, Internet traffic engineering provides
   performance optimization of IP networks while utilizing network
   resources economically and reliably.  Such optimization is supported
   at the control/controller level and within the data/forwarding plane.

   The key elements required in any TE solution are as follows:

   1.  Policy

   2.  Path steering

   3.  Resource management

   Some TE solutions rely on these elements to a lesser or greater
   extent.  Debate remains about whether a solution can truly be called
   "TE" if it does not include all of these elements.  For the sake of
   this document, we assert that all TE solutions must include some
   aspects of all of these elements.  Other solutions can be classed as
   "partial TE" and also fall in scope of this document.

   Policy allows for the selection of paths (including next hops) based
   on information beyond basic reachability.  Early definitions of
   routing policy, e.g., [RFC1102] and [RFC1104], discuss routing policy
   being applied to restrict access to network resources at an aggregate
   level.  BGP is an example of a commonly used mechanism for applying
   such policies; see [RFC4271] and [RFC8955].  In the TE context,
   policy decisions are made within the control plane or by controllers
   in the management plane and govern the selection of paths.  Examples
   can be found in [RFC4655] and [RFC5394].  TE solutions may cover the
   mechanisms to distribute and/or enforce policies, but definition of
   specific policies is left to the network operator.

   Path steering is the ability to forward packets using more
   information than just knowledge of the next hop.  Examples of path
   steering include IPv4 source routes [RFC0791], RSVP-TE explicit
   routes [RFC3209], Segment Routing (SR) [RFC8402], and Service
   Function Chaining [RFC7665].  Path steering for TE can be supported
   via control plane protocols, by encoding in the data plane headers,
   or by a combination of the two.  This includes when control is
   provided by a controller using a network-facing control protocol.

   Resource management provides resource-aware control and forwarding.
   Examples of resources are bandwidth, buffers, and queues, all of
   which can be managed to control loss and latency.

   Resource reservation is the control aspect of resource management.
   It provides for domain-wide consensus about which network resources
   are used by a particular flow.  This determination may be made at a
   very coarse or very fine level.  Note that this consensus exists at
   the network control or controller level but not within the data
   plane.  It may be composed purely of accounting/bookkeeping, but it
   typically includes an ability to admit, reject, or reclassify a flow
   based on policy.  Such accounting can be done based on any
   combination of a static understanding of resource requirements and
   the use of dynamic mechanisms to collect requirements (e.g., via
   RSVP-TE [RFC3209]) and resource availability (e.g., via OSPF
   extensions for GMPLS [RFC4203]).

   Resource allocation is the data plane aspect of resource management.
   It provides for the allocation of specific node and link resources to
   specific flows.  Example resources include buffers, policing, and
   rate-shaping mechanisms that are typically supported via queuing.
   Resource allocation also includes the matching of a flow (i.e., flow
   classification) to a particular set of allocated resources.  The
   method of flow classification and granularity of resource management
   is technology-specific.  Examples include Diffserv with dropping and
   remarking [RFC4594], MPLS-TE [RFC3209], GMPLS-based Label Switched
   Paths (LSPs) [RFC3945], as well as controller-based solutions
   [RFC8453].  This level of resource control, while optional, is
   important in networks that wish to support network congestion
   management policies to control or regulate the offered traffic to
   deliver different levels of service and alleviate network congestion
   problems.  It is also important in networks that wish to control the
   latency experienced by specific traffic flows.

1.3.  Scope

   The scope of this document is intra-domain TE because this is the
   practical level of TE technology that exists in the Internet at the
   time of writing.  That is, this document describes TE within a given
   AS in the Internet.  This document discusses concepts pertaining to
   intra-domain traffic control, including such issues as routing
   control, micro and macro resource allocation, and control
   coordination problems that arise consequently.

   This document describes and characterizes techniques already in use
   or in advanced development for Internet TE.  The way these techniques
   fit together is discussed and scenarios in which they are useful are
   identified.

   Although the emphasis in this document is on intra-domain traffic
   engineering, an overview of the high-level considerations pertaining
   to inter-domain TE is provided in Section 7.  Inter-domain Internet
   TE is crucial to the performance enhancement of the world-wide
   Internet infrastructure.

   Whenever possible, relevant requirements from existing IETF documents
   and other sources are incorporated by reference.

1.4.  Terminology

   This section provides terminology that is useful for Internet TE.
   The definitions presented apply to this document.  These terms may
   have other meanings elsewhere.

   Busy hour:  A one-hour period within a specified interval of time
      (typically 24 hours) in which the traffic load in a network or
      sub-network is greatest.

   Congestion:  A state of a network resource in which the traffic
      incident on the resource exceeds its output capacity over an
      interval of time.  A small amount of congestion may be beneficial
      to ensure that network resources are run at full capacity, and
      this may be particularly true at the network edge where it is
      desirable to ensure that user traffic is served as much as
      possible.  Within the network, if congestion is allowed to build
      (such as when input traffic exceeds output traffic in a sustained
      way), it will have a negative effect on user traffic.

   Congestion avoidance:  An approach to congestion management that
      attempts to obviate the occurrence of congestion.  It is chiefly
      relevant to network congestion, although it may form a part of
      demand-side congestion management.

   Congestion response:  An approach to congestion management that
      attempts to remedy congestion problems that have already occurred.

   Constraint-based routing:  A class of routing protocols that takes
      specified traffic attributes, network constraints, and policy
      constraints into account when making routing decisions.
      Constraint-based routing is applicable to traffic aggregates as
      well as flows.  It is a generalization of QoS-based routing.

   Demand-side congestion management:  A congestion management scheme
      that addresses congestion problems by regulating or conditioning
      the offered load.

   Effective bandwidth:  The minimum amount of bandwidth that can be
      assigned to a flow or traffic aggregate in order to deliver
      "acceptable service quality" to the flow or traffic aggregate.
      See [KELLY] for a more mathematical definition.

   Egress node:  The device (router) at which traffic leaves a network
      toward a destination (host, server, etc.) or to another network.

   End-to-end:  This term is context-dependent and often applies to the
      life of a traffic flow from original source to final destination.
      In contrast, edge-to-edge is often used to describe the traffic
      flow from the entry of a domain or network to the exit of that
      domain or network.  However, in some contexts (for example, where
      there is a service interface between a network and the client of
      that network or where a path traverses multiple domains under the
      control of a single process), end-to-end is used to refer to the
      full operation of the service that may be composed of concatenated
      edge-to-edge operations.  Thus, in the context of TE, the term
      "end-to-end" may refer to the full TE path but not to the complete
      path of the traffic from source application to ultimate
      destination.

   Hotspot:  A network element or subsystem that is in a considerably
      higher state of congestion than others.

   Ingress node:  The device (router) at which traffic enters a network
      from a source (host) or from another network.

   Metric:  A parameter defined in terms of standard units of
      measurement.

   Measurement methodology:  A repeatable measurement technique used to
      derive one or more metrics of interest.

   Network congestion:  Congestion within the network at a specific node
      or a specific link that is sufficiently extreme that it results in
      unacceptable queuing delay or packet loss.  Network congestion can
      negatively impact end-to-end or edge-to-edge traffic flows, so TE
      schemes may be deployed to balance traffic in the network and
      deliver congestion avoidance.

   Network survivability:  The capability to provide a prescribed level
      of QoS for existing services after a given number of failures
      occur within the network.

   Offered load:  Offered load is also sometimes called "offered traffic
      load".  It is a measure of the amount of traffic being presented
      to be carried across a network compared to the capacity of the
      network to carry it.  This term derives from queuing theory, and
      an offered load of 1 indicates that the network can carry, but
      only just manage to carry, all of the traffic presented to it.

   Offline traffic engineering:  A traffic engineering system that
      exists outside of the network.

   Online traffic engineering:  A traffic-engineering system that exists
      within the network, typically implemented on or as adjuncts to
      operational network elements.

   Performance measures:  Metrics that provide quantitative or
      qualitative measures of the performance of systems or subsystems
      of interest.

   Performance metric:  A performance parameter defined in terms of
      standard units of measurement.

   Provisioning:  The process of assigning or configuring network
      resources to meet certain requests.

   Quality of Service (QoS):  QoS [RFC3198] refers to the mechanisms
      used within a network to achieve specific goals for the delivery
      of traffic for a particular service according to the parameters
      specified in a Service Level Agreement.  "Quality" is
      characterized by service availability, delay, jitter, throughput,
      and packet loss ratio.  At a network resource level, "Quality of
      Service" refers to a set of capabilities that allow a service
      provider to prioritize traffic, control bandwidth, and network
      latency.

   QoS routing:  Class of routing systems that selects paths to be used
      by a flow based on the QoS requirements of the flow.

   Service Level Agreement (SLA):  A contract between a provider and a
      customer that guarantees specific levels of performance and
      reliability at a certain cost.

   Service Level Objective (SLO):  A key element of an SLA between a
      provider and a customer.  SLOs are agreed upon as a means of
      measuring the performance of the service provider and are outlined
      as a way of avoiding disputes between the two parties based on
      misunderstanding.

   Stability:  An operational state in which a network does not
      oscillate in a disruptive manner from one mode to another mode.

   Supply-side congestion management:  A congestion management scheme
      that provisions additional network resources to address existing
      and/or anticipated congestion problems.

   Traffic characteristic:  A description of the temporal behavior or a
      description of the attributes of a given traffic flow or traffic
      aggregate.

   Traffic-engineering system:  A collection of objects, mechanisms, and
      protocols that are used together to accomplish traffic-engineering
      objectives.

   Traffic flow:  A stream of packets between two endpoints that can be
      characterized in a certain way.  A common classification for a
      traffic flow selects packets with the five-tuple of source and
      destination addresses, source and destination ports, and protocol
      ID.  Flows may be very small and transient, ranging to very large.
      The TE techniques described in this document are likely to be more
      effective when applied to large flows.  Traffic flows may be
      aggregated and treated as a single unit in some forms of TE,
      making it possible to apply TE to the smaller flows that comprise
      the aggregate.

   Traffic mapping:  Traffic mapping is the assignment of traffic
      workload onto (pre-established) paths to meet certain
      requirements.

   Traffic matrix:  A representation of the traffic demand between a set
      of origin and destination abstract nodes.  An abstract node can
      consist of one or more network elements.

   Traffic monitoring:  The process of observing traffic characteristics
      at a given point in a network and collecting the traffic
      information for analysis and further action.

   Traffic trunk:  An aggregation of traffic flows belonging to the same
      class that are forwarded through a common path.  A traffic trunk
      may be characterized by an ingress and egress node and a set of
      attributes that determine its behavioral characteristics and
      requirements from the network.

   Workload:  Workload is also sometimes called "traffic workload".  It
      is an evaluation of the amount of work that must be done in a
      network in order to facilitate the traffic demand.  Colloquially,
      it is the answer to, "How busy is the network?"

2.  Background

   The Internet aims to convey IP packets from ingress nodes to egress
   nodes efficiently, expeditiously, and economically.  Furthermore, in
   a multi-class service environment (e.g., Diffserv capable networks;
   see Section 5.1.1.2), the resource-sharing parameters of the network
   must be appropriately determined and configured according to
   prevailing policies and service models to resolve resource contention
   issues arising from mutual interference between packets traversing
   the network.  Thus, consideration must be given to resolving
   competition for network resources between traffic flows belonging to
   the same service class (intra-class contention resolution) and
   traffic flows belonging to different classes (inter-class contention
   resolution).

2.1.  Context of Internet Traffic Engineering

   The context of Internet traffic engineering includes the following
   sub-contexts:

   1.  A network domain context that defines the scope under
       consideration and, in particular, the situations in which the TE
       problems occur.  The network domain context includes network
       structure, policies, characteristics, constraints, quality
       attributes, and optimization criteria.

   2.  A problem context defining the general and concrete issues that
       TE addresses.  The problem context includes identification,
       abstraction of relevant features, representation, formulation,
       specification of the requirements on the solution space, and
       specification of the desirable features of acceptable solutions.

   3.  A solution context suggesting how to address the issues
       identified by the problem context.  The solution context includes
       analysis, evaluation of alternatives, prescription, and
       resolution.

   4.  An implementation and operational context in which the solutions
       are instantiated.  The implementation and operational context
       includes planning, organization, and execution.

   The context of Internet TE and the different problem scenarios are
   discussed in the following subsections.

2.2.  Network Domain Context

   IP networks range in size from small clusters of routers situated
   within a given location to thousands of interconnected routers,
   switches, and other components distributed all over the world.

   At the most basic level of abstraction, an IP network can be
   represented as a distributed dynamic system consisting of:

   *  a set of interconnected resources that provide transport services
      for IP traffic subject to certain constraints

   *  a demand system representing the offered load to be transported
      through the network

   *  a response system consisting of network processes, protocols, and
      related mechanisms that facilitate the movement of traffic through
      the network (see also [AWD2])

   The network elements and resources may have specific characteristics
   restricting the manner in which the traffic demand is handled.
   Additionally, network resources may be equipped with traffic control
   mechanisms managing the way in which the demand is serviced.  Traffic
   control mechanisms may be used to:

   *  control packet processing activities within a given resource

   *  arbitrate contention for access to the resource by different
      packets

   *  regulate traffic behavior through the resource

   A configuration management and provisioning system may allow the
   settings of the traffic control mechanisms to be manipulated by
   external or internal entities in order to exercise control over the
   way in which the network elements respond to internal and external
   stimuli.

   The details of how the network carries packets are specified in the
   policies of the network administrators and are installed through
   network configuration management and policy-based provisioning
   systems.  Generally, the types of service provided by the network
   also depend upon the technology and characteristics of the network
   elements and protocols, the prevailing service and utility models,
   and the ability of the network administrators to translate policies
   into network configurations.

   Internet networks have two significant characteristics:

   *  They provide real-time services.

   *  Their operating environments are very dynamic.

   The dynamic characteristics of IP and IP/MPLS networks can be
   attributed in part to fluctuations in demand, the interaction between
   various network protocols and processes, the rapid evolution of the
   infrastructure that demands the constant inclusion of new
   technologies and new network elements, and the transient and
   persistent faults that occur within the system.

   Packets contend for the use of network resources as they are conveyed
   through the network.  A network resource is considered to be
   congested if, for an interval of time, the arrival rate of packets
   exceeds the output capacity of the resource.  Network congestion may
   result in some of the arriving packets being delayed or even dropped.

   Network congestion increases transit delay and delay variation, may
   lead to packet loss, and reduces the predictability of network
   services.  Clearly, while congestion may be a useful tool at ingress
   edge nodes, network congestion is highly undesirable.  Combating
   network congestion at a reasonable cost is a major objective of
   Internet TE, although it may need to be traded with other objectives
   to keep the costs reasonable.

   Efficient sharing of network resources by multiple traffic flows is a
   basic operational premise for the Internet.  A fundamental challenge
   in network operation is to increase resource utilization while
   minimizing the possibility of congestion.

   The Internet has to function in the presence of different classes of
   traffic with different service requirements.  This requirement is
   clarified in the architecture for Differentiated Services (Diffserv)
   [RFC2475].  That document describes how packets can be grouped into
   behavior aggregates such that each aggregate has a common set of
   behavioral characteristics or a common set of delivery requirements.
   Delivery requirements of a specific set of packets may be specified
   explicitly or implicitly.  Two of the most important traffic delivery
   requirements are:

   *  Capacity constraints can be expressed statistically as peak rates,
      mean rates, burst sizes, or as some deterministic notion of
      effective bandwidth.

   *  QoS requirements can be expressed in terms of:

      -  integrity constraints, such as packet loss

      -  temporal constraints, such as timing restrictions for the
         delivery of each packet (delay) and timing restrictions for the
         delivery of consecutive packets belonging to the same traffic
         stream (delay variation)

2.3.  Problem Context

   There are several problems associated with operating a network like
   those described in the previous section.  This section analyzes the
   problem context in relation to TE.  The identification, abstraction,
   representation, and measurement of network features relevant to TE
   are significant issues.

   A particular challenge is to formulate the problems that traffic
   engineering attempts to solve.  For example:

   *  How to identify the requirements on the solution space

   *  How to specify the desirable features of solutions

   *  How to actually solve the problems

   *  How to measure and characterize the effectiveness of solutions

   Another class of problems is how to measure and estimate relevant
   network state parameters.  Effective TE relies on a good estimate of
   the offered traffic load as well as a view of the underlying topology
   and associated resource constraints.  Offline planning requires a
   full view of the topology of the network or partial network that is
   being planned.

   Still another class of problem is how to characterize the state of
   the network and how to evaluate its performance.  The performance
   evaluation problem is two-fold: one aspect relates to the evaluation
   of the system-level performance of the network, and the other aspect
   relates to the evaluation of resource-level performance, which
   restricts attention to the performance analysis of individual network
   resources.

   In this document, we refer to the system-level characteristics of the
   network as the "macro-states" and the resource-level characteristics
   as the "micro-states."  The system-level characteristics are also
   known as the emergent properties of the network.  Correspondingly, we
   refer to the TE schemes dealing with network performance optimization
   at the systems level as "macro-TE" and the schemes that optimize at
   the individual resource level as "micro-TE."  Under certain
   circumstances, the system-level performance can be derived from the
   resource-level performance using appropriate rules of composition,
   depending upon the particular performance measures of interest.

   Another fundamental class of problem concerns how to effectively
   optimize network performance.  Performance optimization may entail
   translating solutions for specific TE problems into network
   configurations.  Optimization may also entail some degree of resource
   management control, routing control, and capacity augmentation.

2.3.1.  Congestion and Its Ramifications

   Network congestion is one of the most significant problems in an
   operational IP context.  A network element is said to be congested if
   it experiences sustained overload over an interval of time.  Although
   congestion at the edge of the network may be beneficial in ensuring
   that the network delivers as much traffic as possible, network
   congestion almost always results in degradation of service quality to
   end users.  Congestion avoidance and response schemes can include
   demand-side policies and supply-side policies.  Demand-side policies
   may restrict access to congested resources or dynamically regulate
   the demand to alleviate the overload situation.  Supply-side policies
   may expand or augment network capacity to better accommodate offered
   traffic.  Supply-side policies may also reallocate network resources
   by redistributing traffic over the infrastructure.  Traffic
   redistribution and resource reallocation serve to increase the
   effective capacity of the network.

   The emphasis of this document is primarily on congestion management
   schemes falling within the scope of the network, rather than on
   congestion management systems dependent upon sensitivity and
   adaptivity from end systems.  That is, the aspects that are
   considered in this document with respect to congestion management are
   those solutions that can be provided by control entities operating on
   the network and by the actions of network administrators and network
   operations systems.

2.4.  Solution Context

   The solution context for Internet TE involves analysis, evaluation of
   alternatives, and choice between alternative courses of action.
   Generally, the solution context is based on making inferences about
   the current or future state of the network and making decisions that
   may involve a preference between alternative sets of action.  More
   specifically, the solution context demands reasonable estimates of
   traffic workload, characterization of network state, derivation of
   solutions that may be implicitly or explicitly formulated, and
   possibly instantiation of a set of control actions.  Control actions
   may involve the manipulation of parameters associated with routing,
   control over tactical capacity acquisition, and control over the
   traffic management functions.

   The following list of instruments may be applicable to the solution
   context of Internet TE:

   *  A set of policies, objectives, and requirements (which may be
      context dependent) for network performance evaluation and
      performance optimization.

   *  A collection of online and, in some cases, possibly offline tools
      and mechanisms for measurement, characterization, modeling,
      control of traffic, control over the placement and allocation of
      network resources, as well as control over the mapping or
      distribution of traffic onto the infrastructure.

   *  A set of constraints on the operating environment, the network
      protocols, and the TE system itself.

   *  A set of quantitative and qualitative techniques and methodologies
      for abstracting, formulating, and solving TE problems.

   *  A set of administrative control parameters that may be manipulated
      through a configuration management system.  Such a system may
      itself include a configuration control subsystem, a configuration
      repository, a configuration accounting subsystem, and a
      configuration auditing subsystem.

   *  A set of guidelines for network performance evaluation,
      performance optimization, and performance improvement.

   Determining traffic characteristics through measurement or estimation
   is very useful within the realm of the TE solution space.  Traffic
   estimates can be derived from customer subscription information,
   traffic projections, traffic models, and actual measurements.  The
   measurements may be performed at different levels, e.g., at the
   traffic-aggregate level or at the flow level.  Measurements at the
   flow level or on small traffic aggregates may be performed at edge
   nodes, when traffic enters and leaves the network.  Measurements for
   large traffic aggregates may be performed within the core of the
   network.

   To conduct performance studies and to support planning of existing
   and future networks, a routing analysis may be performed to determine
   the paths the routing protocols will choose for various traffic
   demands and to ascertain the utilization of network resources as
   traffic is routed through the network.  Routing analysis captures the
   selection of paths through the network, the assignment of traffic
   across multiple feasible routes, and the multiplexing of IP traffic
   over traffic trunks (if such constructs exist) and over the
   underlying network infrastructure.  A model of network topology is
   necessary to perform routing analysis.  A network topology model may
   be extracted from:

   *  network architecture documents

   *  network designs

   *  information contained in router configuration files

   *  routing databases such as the link-state database of an Interior
      Gateway Protocol (IGP)

   *  routing tables

   *  automated tools that discover and collate network topology
      information

   Topology information may also be derived from servers that monitor
   network state and from servers that perform provisioning functions.

   Routing in operational IP networks can be administratively controlled
   at various levels of abstraction, including the manipulation of BGP
   attributes and IGP metrics.  For path-oriented technologies such as
   MPLS, routing can be further controlled by the manipulation of
   relevant TE parameters, resource parameters, and administrative
   policy constraints.  Within the context of MPLS, the path of an
   explicitly routed LSP can be computed and established in various
   ways, including:

   *  manually

   *  automatically and online using constraint-based routing processes
      implemented on Label Switching Routers (LSRs)

   *  automatically and offline using constraint-based routing entities
      implemented on external TE support systems

2.4.1.  Combating the Congestion Problem

   Minimizing congestion is a significant aspect of Internet traffic
   engineering.  This subsection gives an overview of the general
   approaches that have been used or proposed to combat congestion.

   Congestion management policies can be categorized based upon the
   following criteria (see [YARE95] for a more detailed taxonomy of
   congestion control schemes):

   1.  Congestion Management Based on Response Timescales

       *  Long (weeks to months): Expanding network capacity by adding
          new equipment, routers, and links takes time and is
          comparatively costly.  Capacity planning needs to take this
          into consideration.  Network capacity is expanded based on
          estimates or forecasts of future traffic development and
          traffic distribution.  These upgrades are typically carried
          out over weeks, months, or maybe even years.

       *  Medium (minutes to days): Several control policies fall within
          the medium timescale category.  Examples include:

          a.  Adjusting routing protocol parameters to route traffic
              away from or towards certain segments of the network.

          b.  Setting up or adjusting explicitly routed LSPs in MPLS
              networks to route traffic trunks away from possibly
              congested resources or toward possibly more favorable
              routes.

          c.  Reconfiguring the logical topology of the network to make
              it correlate more closely with the spatial traffic
              distribution using, for example, an underlying path-
              oriented technology such as MPLS LSPs or optical channel
              trails.

          When these schemes are adaptive, they rely on measurement
          systems.  A measurement system monitors changes in traffic
          distribution, traffic loads, and network resource utilization
          and then provides feedback to the online or offline TE
          mechanisms and tools so that they can trigger control actions
          within the network.  The TE mechanisms and tools can be
          implemented in a distributed or centralized fashion.  A
          centralized scheme may have full visibility into the network
          state and may produce more optimal solutions.  However,
          centralized schemes are prone to single points of failure and
          may not scale as well as distributed schemes.  Moreover, the
          information utilized by a centralized scheme may be stale and
          might not reflect the actual state of the network.  It is not
          an objective of this document to make a recommendation between
          distributed and centralized schemes; that is a choice that
          network administrators must make based on their specific
          needs.

       *  Short (minutes or less): This category includes packet-level
          processing functions and events that are recorded on the order
          of several round-trip times.  It also includes router
          mechanisms such as passive and active buffer management.  All
          of these mechanisms are used to control congestion or signal
          congestion to end systems so that they can adaptively regulate
          the rate at which traffic is injected into the network.  A
          well-known active queue management scheme, especially for
          responsive traffic such as TCP, is Random Early Detection
          (RED) [FLJA93].  During congestion (but before the queue is
          filled), the RED scheme chooses arriving packets to "mark"
          according to a probabilistic algorithm that takes into account
          the average queue size.  A router that does not utilize
          Explicit Congestion Notification (ECN) [RFC3168] can simply
          drop marked packets to alleviate congestion and implicitly
          notify the receiver about the congestion.  On the other hand,
          if the router and the end hosts support ECN, they can set the
          ECN field in the packet header, and the end host can act on
          this information.  Several variations of RED have been
          proposed to support different drop precedence levels in multi-
          class environments [RFC2597].  RED provides congestion
          avoidance that is better than or equivalent to Tail-Drop (TD)
          queue management (drop arriving packets only when the queue is
          full).  Importantly, RED reduces the possibility of
          retransmission bursts becoming synchronized within the network
          and improves fairness among different responsive traffic
          sessions.  However, RED by itself cannot prevent congestion
          and unfairness caused by sources unresponsive to RED, e.g.,
          some misbehaved greedy connections.  Other schemes have been
          proposed to improve performance and fairness in the presence
          of unresponsive traffic.  Some of those schemes (such as
          Longest Queue Drop (LQD) and Dynamic Soft Partitioning with
          Random Drop (RND) [SLDC98]) were proposed as theoretical
          frameworks and are typically not available in existing
          commercial products, while others (such as Approximate Fair
          Dropping (AFD) [AFD03]) have seen some implementation.  Advice
          on the use of Active Queue Management (AQM) schemes is
          provided in [RFC7567].  [RFC7567] recommends self-tuning AQM
          algorithms like those that the IETF has published in
          [RFC8290], [RFC8033], [RFC8034], and [RFC9332], but RED is
          still appropriate for links with stable bandwidth, if
          configured carefully.

   2.  Reactive versus Preventive Congestion Management Schemes

       *  Reactive (recovery) congestion management policies react to
          existing congestion problems.  All the policies described
          above for the short and medium timescales can be categorized
          as being reactive.  They are based on monitoring and
          identifying congestion problems that exist in the network and
          on the initiation of relevant actions to ease a situation.
          Reactive congestion management schemes may also be preventive.

       *  Preventive (predictive/avoidance) policies take proactive
          action to prevent congestion based on estimates and
          predictions of future congestion problems (e.g., traffic
          matrix forecasts).  Some of the policies described for the
          long and medium timescales fall into this category.
          Preventive policies do not necessarily respond immediately to
          existing congestion problems.  Instead, forecasts of traffic
          demand and workload distribution are considered, and action
          may be taken to prevent potential future congestion problems.
          The schemes described for the short timescale can also be used
          for congestion avoidance because dropping or marking packets
          before queues actually overflow would trigger corresponding
          responsive traffic sources to slow down.  Preventive
          congestion management schemes may also be reactive.

   3.  Supply-Side versus Demand-Side Congestion Management Schemes

       *  Supply-side congestion management policies increase the
          effective capacity available to traffic in order to control or
          reduce congestion.  This can be accomplished by increasing
          capacity or by balancing distribution of traffic over the
          network.  Capacity planning aims to provide a physical
          topology and associated link bandwidths that match or exceed
          estimated traffic workload and traffic distribution, subject
          to traffic forecasts and budgetary (or other) constraints.  If
          the actual traffic distribution does not fit the topology
          derived from capacity planning, then the traffic can be mapped
          onto the topology by using routing control mechanisms, by
          applying path-oriented technologies (e.g., MPLS LSPs and
          optical channel trails) to modify the logical topology or by
          employing some other load redistribution mechanisms.

       *  Demand-side congestion management policies control or regulate
          the offered traffic to alleviate congestion problems.  For
          example, some of the short timescale mechanisms described
          earlier as well as policing and rate-shaping mechanisms
          attempt to regulate the offered load in various ways.

2.5.  Implementation and Operational Context

   The operational context of Internet TE is characterized by constant
   changes that occur at multiple levels of abstraction.  The
   implementation context demands effective planning, organization, and
   execution.  The planning aspects may involve determining prior sets
   of actions to achieve desired objectives.  Organizing involves
   arranging and assigning responsibility to the various components of
   the TE system and coordinating the activities to accomplish the
   desired TE objectives.  Execution involves measuring and applying
   corrective or perfective actions to attain and maintain desired TE
   goals.

3.  Traffic-Engineering Process Models

   This section describes a generic process model that captures the
   high-level practical aspects of Internet traffic engineering in an
   operational context.  The process model is described as a sequence of
   actions that must be carried out to optimize the performance of an
   operational network (see also [RFC2702] and [AWD2]).  This process
   model may be enacted explicitly or implicitly, by a software process
   or by a human.

   The TE process model is iterative [AWD2].  The four phases of the
   process model described below are repeated as a continual sequence:

   1.  Define the relevant control policies that govern the operation of
       the network.

   2.  Acquire measurement data from the operational network.

   3.  Analyze the network state and characterize the traffic workload.
       Proactive analysis identifies potential problems that could
       manifest in the future.  Reactive analysis identifies existing
       problems and determines their causes.

   4.  Optimize the performance of the network.  This involves a
       decision process that selects and implements a set of actions
       from a set of alternatives given the results of the three
       previous steps.  Optimization actions may include the use of
       techniques to control the offered traffic and to control the
       distribution of traffic across the network.

3.1.  Components of the Traffic-Engineering Process Model

   The key components of the traffic-engineering process model are as
   follows:

   1.  Measurement is crucial to the TE function.  The operational state
       of a network can only be conclusively determined through
       measurement.  Measurement is also critical to the optimization
       function because it provides feedback data that is used by TE
       control subsystems.  This data is used to adaptively optimize
       network performance in response to events and stimuli originating
       within and outside the network.  Measurement in support of the TE
       function can occur at different levels of abstraction.  For
       example, measurement can be used to derive packet-level
       characteristics, flow-level characteristics, user- or customer-
       level characteristics, traffic-aggregate characteristics,
       component-level characteristics, and network-wide
       characteristics.

   2.  Modeling, analysis, and simulation are important aspects of
       Internet TE.  Modeling involves constructing an abstract or
       physical representation that depicts relevant traffic
       characteristics and network attributes.  A network model is an
       abstract representation of the network that captures relevant
       network features, attributes, and characteristics.  Network
       simulation tools are extremely useful for TE.  Because of the
       complexity of realistic quantitative analysis of network
       behavior, certain aspects of network performance studies can only
       be conducted effectively using simulation.

   3.  Network performance optimization involves resolving network
       issues by transforming such issues into concepts that enable a
       solution, identification of a solution, and implementation of the
       solution.  Network performance optimization can be corrective or
       perfective.  In corrective optimization, the goal is to remedy a
       problem that has occurred or that is incipient.  In perfective
       optimization, the goal is to improve network performance even
       when explicit problems do not exist and are not anticipated.

4.  Taxonomy of Traffic-Engineering Systems

   This section presents a short taxonomy of traffic-engineering systems
   constructed based on TE styles and views as listed below and
   described in greater detail in the following subsections of this
   document:

   *  Time-Dependent versus State-Dependent versus Event-Dependent

   *  Offline versus Online

   *  Centralized versus Distributed

   *  Local versus Global Information

   *  Prescriptive versus Descriptive

   *  Open-Loop versus Closed-Loop

   *  Tactical versus Strategic

4.1.  Time-Dependent versus State-Dependent versus Event-Dependent

   Traffic-engineering methodologies can be classified as time-
   dependent, state-dependent, or event-dependent.  All TE schemes are
   considered to be dynamic in this document.  Static TE implies that no
   TE methodology or algorithm is being applied -- it is a feature of
   network planning but lacks the reactive and flexible nature of TE.

   In time-dependent TE, historical information based on periodic
   variations in traffic (such as time of day) is used to pre-program
   routing and other TE control mechanisms.  Additionally, customer
   subscription or traffic projection may be used.  Pre-programmed
   routing plans typically change on a relatively long timescale (e.g.,
   daily).  Time-dependent algorithms do not attempt to adapt to short-
   term variations in traffic or changing network conditions.  An
   example of a time-dependent algorithm is a centralized optimizer
   where the input to the system is a traffic matrix and multi-class QoS
   requirements as described in [MR99].  Another example of such a
   methodology is the application of data mining to Internet traffic
   [AJ19], which enables the use of various machine learning algorithms
   to identify patterns within historically collected datasets about
   Internet traffic and to extract information in order to guide
   decision-making and improve efficiency and productivity of
   operational processes.

   State-dependent TE adapts the routing plans based on the current
   state of the network, which provides additional information on
   variations in actual traffic (i.e., perturbations from regular
   variations) that could not be predicted using historical information.
   Constraint-based routing is an example of state-dependent TE
   operating in a relatively long timescale.  An example of operating in
   a relatively short timescale is a load-balancing algorithm described
   in [MATE].  The state of the network can be based on parameters
   flooded by the routers.  Another approach is for a particular router
   performing adaptive TE to send probe packets along a path to gather
   the state of that path.  [RFC6374] defines protocol extensions to
   collect performance measurements from MPLS networks.  Another
   approach is for a management system to gather the relevant
   information directly from network elements using telemetry data
   collection publication/subscription techniques [RFC7923].  Timely
   gathering and distribution of state information is critical for
   adaptive TE.  While time-dependent algorithms are suitable for
   predictable traffic variations, state-dependent algorithms may be
   needed to increase network efficiency and to provide resilience to
   adapt to changes in network state.

   Event-dependent TE methods can also be used for TE path selection.
   Event-dependent TE methods are distinct from time-dependent and
   state-dependent TE methods in the manner in which paths are selected.
   These algorithms are adaptive and distributed in nature, and they
   typically use learning models to find good paths for TE in a network.
   While state-dependent TE models typically use available-link-
   bandwidth (ALB) flooding [E.360.1] for TE path selection, event-
   dependent TE methods do not require ALB flooding.  Rather, event-
   dependent TE methods typically search out capacity by learning
   models, as in the success-to-the-top (STT) method [RFC6601].  ALB
   flooding can be resource intensive, since it requires link bandwidth
   to carry routing protocol link-state advertisements and processor
   capacity to process those advertisements; in addition, the overhead
   of the ALB advertisements and their processing can limit the size of
   the area and AS.  Modeling results suggest that event-dependent TE
   methods could lead to a reduction in ALB flooding overhead without
   loss of network throughput performance [TE-QoS-ROUTING].

   A fully functional TE system is likely to use all aspects of time-
   dependent, state-dependent, and event-dependent methodologies as
   described in Section 4.3.1.

4.2.  Offline versus Online

   Traffic engineering requires the computation of routing plans.  The
   computation may be performed offline or online.  The computation can
   be done offline for scenarios where routing plans need not be
   executed in real time.  For example, routing plans computed from
   forecast information may be computed offline.  Typically, offline
   computation is also used to perform extensive searches on multi-
   dimensional solution spaces.

   Online computation is required when the routing plans must adapt to
   changing network conditions as in state-dependent algorithms.  Unlike
   offline computation (which can be computationally demanding), online
   computation is geared toward relatively simple and fast calculations
   to select routes, fine-tune the allocations of resources, and perform
   load balancing.

4.3.  Centralized versus Distributed

   Under centralized control, there is a central authority that
   determines routing plans and perhaps other TE control parameters on
   behalf of each router.  The central authority periodically collects
   network-state information from all routers and sends routing
   information to the routers.  The update cycle for information
   exchange in both directions is a critical parameter directly
   impacting the performance of the network being controlled.
   Centralized control may need high processing power and high bandwidth
   control channels.

   Distributed control determines route selection by each router
   autonomously based on the router's view of the state of the network.
   The network state information may be obtained by the router using a
   probing method or distributed by other routers on a periodic basis
   using link-state advertisements.  Network state information may also
   be disseminated under exception conditions.  Examples of protocol
   extensions used to advertise network link-state information are
   defined in [RFC5305], [RFC6119], [RFC7471], [RFC8570], and [RFC8571].
   See also Section 5.1.3.9.

4.3.1.  Hybrid Systems

   In practice, most TE systems will be a hybrid of central and
   distributed control.  For example, a popular MPLS approach to TE is
   to use a central controller based on an active, stateful Path
   Computation Element (PCE) but to use routing and signaling protocols
   to make local decisions at routers within the network.  Local
   decisions may be able to respond more quickly to network events but
   may result in conflicts with decisions made by other routers.

   Network operations for TE systems may also use a hybrid of offline
   and online computation.  TE paths may be precomputed based on stable-
   state network information and planned traffic demands but may then be
   modified in the active network depending on variations in network
   state and traffic load.  Furthermore, responses to network events may
   be precomputed offline to allow rapid reactions without further
   computation or may be derived online depending on the nature of the
   events.

4.3.2.  Considerations for Software-Defined Networking

   As discussed in Section 5.1.2.2, one of the main drivers for
   Software-Defined Networking (SDN) is a decoupling of the network
   control plane from the data plane [RFC7149].  However, SDN may also
   combine centralized control of resources and facilitate application-
   to-network interaction via an Application Programming Interface
   (API), such as the one described in [RFC8040].  Combining these
   features provides a flexible network architecture that can adapt to
   the network requirements of a variety of higher-layer applications, a
   concept often referred to as the "programmable network" [RFC7426].

   The centralized control aspect of SDN helps improve network resource
   utilization compared with distributed network control, where local
   policy may often override network-wide optimization goals.  In an SDN
   environment, the data plane forwards traffic to its desired
   destination.  However, before traffic reaches the data plane, the
   logically centralized SDN control plane often determines the path the
   application traffic will take in the network.  Therefore, the SDN
   control plane needs to be aware of the underlying network topology,
   capabilities, and current node and link resource state.

   Using a PCE-based SDN control framework [RFC7491], the available
   network topology may be discovered by running a passive instance of
   OSPF or IS-IS, or via BGP Link State (BGP-LS) [RFC9552]), to generate
   a Traffic Engineering Database (TED) (see Section 5.1.3.14).  The PCE
   is used to compute a path (see Section 5.1.3.11) based on the TED and
   available bandwidth, and further path optimization may be based on
   requested objective functions [RFC5541].  When a suitable path has
   been computed, the programming of the explicit network path may be
   either performed using a signaling protocol that traverses the length
   of the path [RFC3209] or performed per-hop with each node being
   directly programmed [RFC8283] by the SDN controller.

   By utilizing a centralized approach to network control, additional
   network benefits are also available, including Global Concurrent
   Optimization (GCO) [RFC5557].  A GCO path computation request will
   simultaneously use the network topology and a set of new path
   signaling requests, along with their respective constraints, for
   optimal placement in the network.  Correspondingly, a GCO-based
   computation may be applied to recompute existing network paths to
   groom traffic and to mitigate congestion.

4.4.  Local versus Global

   Traffic-engineering algorithms may require local and global network-
   state information.

   Local information is the state of a portion of the domain.  Examples
   include the bandwidth and packet loss rate of a particular path or
   the state and capabilities of a network link.  Local state
   information may be sufficient for certain instances of distributed
   control TE.

   Global information is the state of the entire TE domain.  Examples
   include a global traffic matrix and loading information on each link
   throughout the domain of interest.  Global state information is
   typically required with centralized control.  Distributed TE systems
   may also need global information in some cases.

4.5.  Prescriptive versus Descriptive

   TE systems may also be classified as prescriptive or descriptive.

   Prescriptive traffic engineering evaluates alternatives and
   recommends a course of action.  Prescriptive TE can be further
   categorized as either corrective or perfective.  Corrective TE
   prescribes a course of action to address an existing or predicted
   anomaly.  Perfective TE prescribes a course of action to evolve and
   improve network performance even when no anomalies are evident.

   Descriptive traffic engineering, on the other hand, characterizes the
   state of the network and assesses the impact of various policies
   without recommending any particular course of action.

4.5.1.  Intent-Based Networking

   One way to express a service request is through "intent".  Intent-
   Based Networking aims to produce networks that are simpler to manage
   and operate, requiring only minimal intervention.  Intent is defined
   in [RFC9315] as follows:

   |  A set of operational goals (that a network should meet) and
   |  outcomes (that a network is supposed to deliver) defined in a
   |  declarative manner without specifying how to achieve or implement
   |  them.

   Intent provides data and functional abstraction so that users and
   operators do not need to be concerned with low-level device
   configuration or the mechanisms used to achieve a given intent.  This
   approach can be conceptually easier for a user but may be less
   expressive in terms of constraints and guidelines.

   Intent-Based Networking is applicable to TE because many of the high-
   level objectives may be expressed as intent (for example, load
   balancing, delivery of services, and robustness against failures).
   The intent is converted by the management system into TE actions
   within the network.

4.6.  Open-Loop versus Closed-Loop

   Open-loop traffic-engineering control is where control action does
   not use feedback information from the current network state.
   However, the control action may use its own local information for
   accounting purposes.

   Closed-loop traffic-engineering control is where control action
   utilizes feedback information from the network state.  The feedback
   information may be in the form of current measurement or recent
   historical records.

4.7.  Tactical versus Strategic

   Tactical traffic engineering aims to address specific performance
   problems (such as hotspots) that occur in the network from a tactical
   perspective, without consideration of overall strategic imperatives.
   Without proper planning and insights, tactical TE tends to be ad hoc
   in nature.

   Strategic traffic-engineering approaches the TE problem from a more
   organized and systematic perspective, taking into consideration the
   immediate and longer-term consequences of specific policies and
   actions.

5.  Review of TE Techniques

   This section briefly reviews different TE-related approaches proposed
   and implemented in telecommunications and computer networks using
   IETF protocols and architectures.  These approaches are organized
   into three categories:

   *  TE mechanisms that adhere to the definition provided in
      Section 1.2

   *  Approaches that rely upon those TE mechanisms

   *  Techniques that are used by those TE mechanisms and approaches

   The discussion is not intended to be comprehensive.  It is primarily
   intended to illuminate existing approaches to TE in the Internet.  A
   historic overview of TE in telecommunications networks was provided
   in Section 4 of [RFC3272], and Section 4.6 of that document presented
   an outline of some early approaches to TE conducted in other
   standards bodies.  It is out of the scope of this document to provide
   an analysis of the history of TE or an inventory of TE-related
   efforts conducted by other Standards Development Organizations
   (SDOs).

5.1.  Overview of IETF Projects Related to Traffic Engineering

   This subsection reviews a number of IETF activities pertinent to
   Internet traffic engineering.  Some of these technologies are widely
   deployed, others are mature but have seen less deployment, and some
   are unproven or are still under development.

5.1.1.  IETF TE Mechanisms

5.1.1.1.  Integrated Services

   The IETF developed the Integrated Services (Intserv) model that
   requires resources, such as bandwidth and buffers, to be reserved a
   priori for a given traffic flow to ensure that the QoS requested by
   the traffic flow is satisfied.  The Intserv model includes additional
   components beyond those used in the best-effort model such as packet
   classifiers, packet schedulers, and admission control.  A packet
   classifier is used to identify flows that are to receive a certain
   level of service.  A packet scheduler handles the scheduling of
   service to different packet flows to ensure that QoS commitments are
   met.  Admission control is used to determine whether a router has the
   necessary resources to accept a new flow.

   The main issue with the Intserv model has been scalability [RFC2998],
   especially in large public IP networks that may potentially have
   millions of active traffic flows in transit concurrently.  Pre-
   Congestion Notification (PCN) [RFC5559] solves the scaling problems
   of Intserv by using measurement-based admission control (and flow
   termination to handle failures) between edge nodes.  Nodes between
   the edges of the internetwork have no per-flow operations, and the
   edge nodes can use the Resource Reservation Protocol (RSVP) per-flow
   or per-aggregate.

   A notable feature of the Intserv model is that it requires explicit
   signaling of QoS requirements from end systems to routers [RFC2753].
   RSVP performs this signaling function and is a critical component of
   the Intserv model.  RSVP is described in Section 5.1.3.2.

5.1.1.2.  Differentiated Services

   The goal of Differentiated Services (Diffserv) within the IETF was to
   devise scalable mechanisms for categorization of traffic into
   behavior aggregates, which ultimately allows each behavior aggregate
   to be treated differently, especially when there is a shortage of
   resources, such as link bandwidth and buffer space [RFC2475].  One of
   the primary motivations for Diffserv was to devise alternative
   mechanisms for service differentiation in the Internet that mitigate
   the scalability issues encountered with the Intserv model.

   Diffserv uses the Differentiated Services field in the IP header (the
   DS field) consisting of six bits in what was formerly known as the
   Type of Service (TOS) octet.  The DS field is used to indicate the
   forwarding treatment that a packet should receive at a transit node
   [RFC2474].  Diffserv includes the concept of Per-Hop Behavior (PHB)
   groups.  Using the PHBs, several classes of services can be defined
   using different classification, policing, shaping, and scheduling
   rules.

   For an end user of network services to utilize Diffserv provided by
   its Internet Service Provider (ISP), it may be necessary for the user
   to have an SLA with the ISP.  An SLA may explicitly or implicitly
   specify a Traffic Conditioning Agreement (TCA) that defines
   classifier rules as well as metering, marking, discarding, and
   shaping rules.

   Packets are classified and possibly policed and shaped at the ingress
   to a Diffserv network.  When a packet traverses the boundary between
   different Diffserv domains, the DS field of the packet may be re-
   marked according to existing agreements between the domains.

   Diffserv allows only a finite number of service classes to be
   specified by the DS field.  The main advantage of the Diffserv
   approach relative to the Intserv model is scalability.  Resources are
   allocated on a per-class basis, and the amount of state information
   is proportional to the number of classes rather than to the number of
   application flows.

   Once the network has been planned and the packets have been marked at
   the network edge, the Diffserv model deals with traffic management
   issues on a per-hop basis.  The Diffserv control model consists of a
   collection of micro-TE control mechanisms.  Other TE capabilities,
   such as capacity management (including routing control), are also
   required in order to deliver acceptable service quality in Diffserv
   networks.  The concept of "Per-Domain Behaviors" has been introduced
   to better capture the notion of Diffserv across a complete domain
   [RFC3086].

   Diffserv procedures can also be applied in an MPLS context.  See
   Section 6.8 for more information.

5.1.1.3.  SR Policy

   SR Policy [RFC9256] is an evolution of SR (see Section 5.1.3.12) to
   enhance the TE capabilities of SR.  It is a framework that enables
   instantiation of an ordered list of segments on a node for
   implementing a source routing policy with a specific intent for
   traffic steering from that node.

   An SR Policy is identified through the tuple <headend, color,
   endpoint>.  The headend is the IP address of the node where the
   policy is instantiated.  The endpoint is the IP address of the
   destination of the policy.  The color is an index that associates the
   SR Policy with an intent (e.g., low latency).

   The headend node is notified of SR Policies and associated SR paths
   via configuration or by extensions to protocols such as the Path
   Computation Element Communication Protocol (PCEP) [RFC8664] or BGP
   [SR-TE-POLICY].  Each SR path consists of a segment list (an SR
   source-routed path), and the headend uses the endpoint and color
   parameters to classify packets to match the SR Policy and so
   determine along which path to forward them.  If an SR Policy is
   associated with a set of SR paths, each is associated with a weight
   for weighted load balancing.  Furthermore, multiple SR Policies may
   be associated with a set of SR paths to allow multiple traffic flows
   to be placed on the same paths.

   An SR Binding SID (BSID) may also be associated with each candidate
   path associated with an SR Policy or with the SR Policy itself.  The
   headend node installs a BSID-keyed entry in the forwarding plane and
   assigns it the action of steering packets that match the entry to the
   selected path of the SR Policy.  This steering can be done in various
   ways:

   SID Steering:  Incoming packets have an active Segment Identifier
      (SID) matching a local BSID at the headend.

   Per-destination Steering:  Incoming packets match a BGP/Service
      route, which indicates an SR Policy.

   Per-flow Steering:  Incoming packets match a forwarding array (for
      example, the classic 5-tuple), which indicates an SR Policy.

   Policy-based Steering:  Incoming packets match a routing policy,
      which directs them to an SR Policy.

5.1.1.4.  Layer 4 Transport-Based TE

   In addition to IP-based TE mechanisms, Layer 4 transport-based TE
   approaches can be considered in specific deployment contexts (e.g.,
   data centers and multi-homing).  For example, the 3GPP defines the
   Access Traffic Steering, Switching, and Splitting (ATSSS) [ATSSS]
   service functions as follows:

   Access Traffic Steering:  This is the selection of an access network
      for a new flow and the transfer of the traffic of that flow over
      the selected access network.

   Access Traffic Switching:  This is the migration of all packets of an
      ongoing flow from one access network to another access network.
      Only one access network is in use at a time.

   Access Traffic Splitting:  This is about forwarding the packets of a
      flow across multiple access networks simultaneously.

   The control plane is used to provide hosts and specific network
   devices with a set of policies that specify which flows are eligible
   to use the ATSSS service.  The traffic that matches an ATSSS policy
   can be distributed among the available access networks following one
   of the following four modes:

   Active-Standby:  The traffic is forwarded via a specific access
      (called "active access") and switched to another access (called
      "standby access") when the active access is unavailable.

   Priority-based:  Network accesses are assigned priority levels that
      indicate which network access is to be used first.  The traffic
      associated with the matching flow will be steered onto the network
      access with the highest priority until congestion is detected.
      Then, the overflow will be forwarded over the next highest
      priority access.

   Load-Balancing:  The traffic is distributed among the available
      access networks following a distribution ratio (e.g., 75% to 25%).

   Smallest Delay:  The traffic is forwarded via the access that
      presents the smallest round-trip time (RTT).

   For resource management purposes, hosts and network devices support
   means such as congestion control, RTT measurement, and packet
   scheduling.

   For TCP traffic, Multipath TCP [RFC8684] and the 0-RTT Convert
   Protocol [RFC8803] are used to provide the ATSSS service.

   Multipath QUIC [QUIC-MULTIPATH] and Proxying UDP in HTTP [RFC9298]
   are used to provide the ATSSS service for UDP traffic.  Note that
   QUIC [RFC9000] supports the switching and steering functions.
   Indeed, QUIC supports a connection migration procedure that allows
   peers to change their Layer 4 transport coordinates (IP addresses,
   port numbers) without breaking the underlying QUIC connection.

   Extensions to the Datagram Congestion Control Protocol (DCCP)
   [RFC4340] to support multipath operations are defined in
   [MULTIPATH-DCCP].

5.1.1.5.  Deterministic Networking

   Deterministic Networking (DetNet) [RFC8655] is an architecture for
   applications with critical timing and reliability requirements.  The
   layered architecture particularly focuses on developing DetNet
   service capabilities in the data plane [RFC8938].  The DetNet service
   sub-layer provides a set of Packet Replication, Elimination, and
   Ordering Functions (PREOF) to provide end-to-end service assurance.
   The DetNet forwarding sub-layer provides corresponding forwarding
   assurance (low packet loss, bounded latency, and in-order delivery)
   functions using resource allocations and explicit route mechanisms.

   The separation into two sub-layers allows a greater flexibility to
   adapt DetNet capability over a number of TE data plane mechanisms,
   such as IP, MPLS, and SR.  More importantly, it interconnects IEEE
   802.1 Time Sensitive Networking (TSN) [RFC9023] deployed in Industry
   Control and Automation Systems (ICAS).

   DetNet can be seen as a specialized branch of TE, since it sets up
   explicit optimized paths with allocation of resources as requested.
   A DetNet application can express its QoS attributes or traffic
   behavior using any combination of DetNet functions described in sub-
   layers.  They are then distributed and provisioned using well-
   established control and provisioning mechanisms adopted for traffic
   engineering.

   In DetNet, a considerable amount of state information is required to
   maintain per-flow queuing disciplines and resource reservation for a
   large number of individual flows.  This can be quite challenging for
   network operations during network events, such as faults, change in
   traffic volume, or reprovisioning.  Therefore, DetNet recommends
   support for aggregated flows; however, it still requires a large
   amount of control signaling to establish and maintain DetNet flows.

   Note that DetNet might suffer from some of the scalability concerns
   described for Intserv in Section 5.1.1.1, but the scope of DetNet's
   deployment scenarios is smaller and therefore less exposed to scaling
   issues.

5.1.2.  IETF Approaches Relying on TE Mechanisms

5.1.2.1.  Application-Layer Traffic Optimization

   This document describes various TE mechanisms available in the
   network.  However, in general, distributed applications
   (particularly, bandwidth-greedy P2P applications that are used for
   file sharing, for example) cannot directly use those techniques.  As
   per [RFC5693], applications could greatly improve traffic
   distribution and quality by cooperating with external services that
   are aware of the network topology.  Addressing the Application-Layer
   Traffic Optimization (ALTO) problem means, on the one hand, deploying
   an ALTO service to provide applications with information regarding
   the underlying network (e.g., basic network location structure and
   preferences of network paths) and, on the other hand, enhancing
   applications in order to use such information to perform better-than-
   random selection of the endpoints with which they establish
   connections.

   The basic function of ALTO is based on abstract maps of a network.
   These maps provide a simplified view, yet enough information about a
   network for applications to effectively utilize them.  Additional
   services are built on top of the maps.  [RFC7285] describes a
   protocol implementing the ALTO services as an information-publishing
   interface that allows a network to publish its network information to
   network applications.  This information can include network node
   locations, groups of node-to-node connectivity arranged by cost
   according to configurable granularities, and end-host properties.
   The information published by the ALTO Protocol should benefit both
   the network and the applications.  The ALTO Protocol uses a REST-ful
   design and encodes its requests and responses using JSON [RFC8259]
   with a modular design by dividing ALTO information publication into
   multiple ALTO services (e.g., the Map Service, the Map-Filtering
   Service, the Endpoint Property Service, and the Endpoint Cost
   Service).

   [RFC8189] defines a new service that allows an ALTO Client to
   retrieve several cost metrics in a single request for an ALTO
   filtered cost map and endpoint cost map.  [RFC8896] extends the ALTO
   cost information service so that applications decide not only "where"
   to connect but also "when".  This is useful for applications that
   need to perform bulk data transfer and would like to schedule these
   transfers during an off-peak hour, for example.  [RFC9439] introduces
   network performance metrics, including network delay, jitter, packet
   loss rate, hop count, and bandwidth.  The ALTO server may derive and
   aggregate such performance metrics from BGP-LS (see
   Section 5.1.3.10), IGP-TE (see Section 5.1.3.9), or management tools
   and then expose the information to allow applications to determine
   "where" to connect based on network performance criteria.  The ALTO
   Working Group is evaluating the use of network TE properties while
   making application decisions for new use cases such as edge computing
   and data-center interconnect.

5.1.2.2.  Network Virtualization and Abstraction

   One of the main drivers for SDN [RFC7149] is a decoupling of the
   network control plane from the data plane.  This separation has been
   achieved for TE networks with the development of MPLS and GMPLS (see
   Sections 5.1.3.3 and 5.1.3.5, respectively) and the PCE (see
   Section 5.1.3.11).  One of the advantages of SDN is its logically
   centralized control regime that allows a full view of the underlying
   networks.  Centralized control in SDN helps improve network resource
   utilization compared with distributed network control.

   Abstraction and Control of TE Networks (ACTN) [RFC8453] defines a
   hierarchical SDN architecture that describes the functional entities
   and methods for the coordination of resources across multiple
   domains, to provide composite traffic-engineered services.  ACTN
   facilitates composed, multi-domain connections and provides them to
   the user.  ACTN is focused on:

   *  Abstraction of the underlying network resources and how they are
      provided to higher-layer applications and customers.

   *  Virtualization of underlying resources for use by the customer,
      application, or service.  The creation of a virtualized
      environment allows operators to view and control multi-domain
      networks as a single virtualized network.

   *  Presentation to customers of networks as a virtual network via
      open and programmable interfaces.

   The ACTN managed infrastructure is built from traffic-engineered
   network resources, which may include statistical packet bandwidth,
   physical forwarding-plane sources (such as wavelengths and time
   slots), and forwarding and cross-connect capabilities.  The type of
   network virtualization seen in ACTN allows customers and applications
   (tenants) to utilize and independently control allocated virtual
   network resources as if they were physically their own resource.  The
   ACTN network is sliced, with tenants being given a different partial
   and abstracted topology view of the physical underlying network.

5.1.2.3.  Network Slicing

   An IETF Network Slice is a logical network topology connecting a
   number of endpoints using a set of shared or dedicated network
   resources [NETWORK-SLICES].  The resources are used to satisfy
   specific SLOs specified by the consumer.

   IETF Network Slices are not, of themselves, TE constructs.  However,
   a network operator that offers IETF Network Slices is likely to use
   many TE tools in order to manage their network and provide the
   services.

   IETF Network Slices are defined such that they are independent of the
   underlying infrastructure connectivity and technologies used.  From a
   customer's perspective, an IETF Network Slice looks like a VPN
   connectivity matrix with additional information about the level of
   service that the customer requires between the endpoints.  From an
   operator's perspective, the IETF Network Slice looks like a set of
   routing or tunneling instructions with the network resource
   reservations necessary to provide the required service levels as
   specified by the SLOs.  The concept of an IETF Network Slice is
   consistent with an enhanced VPN [ENHANCED-VPN].

5.1.3.  IETF Techniques Used by TE Mechanisms

5.1.3.1.  Constraint-Based Routing

   Constraint-based routing refers to a class of routing systems that
   compute routes through a network subject to the satisfaction of a set
   of constraints and requirements.  In the most general case,
   constraint-based routing may also seek to optimize overall network
   performance while minimizing costs.

   The constraints and requirements may be imposed by the network itself
   or by administrative policies.  Constraints may include bandwidth,
   hop count, delay, and policy instruments such as resource class
   attributes.  Constraints may also include domain-specific attributes
   of certain network technologies and contexts that impose restrictions
   on the solution space of the routing function.  Path-oriented
   technologies such as MPLS have made constraint-based routing feasible
   and attractive in public IP networks.

   The concept of constraint-based routing within the context of MPLS-TE
   requirements in IP networks was first described in [RFC2702] and led
   to developments such as MPLS-TE [RFC3209] as described in
   Section 5.1.3.3.

   Unlike QoS-based routing (for example, see [RFC2386], [MA], and
   [PERFORMANCE-ROUTING]) that generally addresses the issue of routing
   individual traffic flows to satisfy prescribed flow-based QoS
   requirements subject to network resource availability, constraint-
   based routing is applicable to traffic aggregates as well as flows
   and may be subject to a wide variety of constraints that may include
   policy restrictions.

5.1.3.1.1.  IGP Flexible Algorithms

   The normal approach to routing in an IGP network relies on the IGPs
   deriving "shortest paths" over the network based solely on the IGP
   metric assigned to the links.  Such an approach is often limited:
   traffic may tend to converge toward the destination, possibly causing
   congestion, and it is not possible to steer traffic onto paths
   depending on the end-to-end qualities demanded by the applications.

   To overcome this limitation, various sorts of TE have been widely
   deployed (as described in this document), where the TE component is
   responsible for computing the path based on additional metrics and/or
   constraints.  Such paths (or tunnels) need to be installed in the
   routers' forwarding tables in addition to, or as a replacement for,
   the original paths computed by IGPs.  The main drawbacks of these TE
   approaches are the additional complexity of protocols and management
   and the state that may need to be maintained within the network.

   IGP Flexible Algorithms [RFC9350] allow IGPs to construct constraint-
   based paths over the network by computing constraint-based next hops.
   The intent of Flexible Algorithms is to reduce TE complexity by
   letting an IGP perform some basic TE computation capabilities.
   Flexible Algorithm includes a set of extensions to the IGPs that
   enable a router to send TLVs that:

   *  describe a set of constraints on the topology

   *  identify calculation-type

   *  describe a metric-type that is to be used to compute the best
      paths through the constrained topology

   A given combination of calculation-type, metric-type, and constraints
   is known as a Flexible Algorithm Definition (FAD).  A router that
   sends such a set of TLVs also assigns a specific identifier (the
   Flexible Algorithm) to the specified combination of calculation-type,
   metric-type, and constraints.

   There are two use cases for Flexible Algorithm: in IP networks
   [RFC9502] and in SR networks [RFC9350].  In the first case, Flexible
   Algorithm computes paths to an IPv4 or IPv6 address; in the second
   case, Flexible Algorithms computes paths to a Prefix SID (see
   Section 5.1.3.12).

   Examples of where Flexible Algorithms can be useful include:

   *  Expansion of the function of IP performance metrics [RFC5664]
      where specific constraint-based routing (Flexible Algorithm) can
      be instantiated within the network based on the results of
      performance measurement.

   *  The formation of an "underlay" network using Flexible Algorithms,
      and the realization of an "overlay" network using TE techniques.
      This approach can leverage the nested combination of Flexible
      Algorithm and TE extensions for IGP (see Section 5.1.3.9).

   *  Flexible Algorithms in SR-MPLS (Section 5.1.3.12) can be used as a
      base to easily build a TE-like topology without TE components on
      routers or the use of a PCE (see Section 5.1.3.11).

   *  The support for network slices [NETWORK-SLICES] where the SLOs of
      a particular IETF Network Slice can be guaranteed by a Flexible
      Algorithm or where a Filtered Topology [NETWORK-SLICES] can be
      created as a TE-like topology using a Flexible Algorithm.

5.1.3.2.  RSVP

   RSVP is a soft-state signaling protocol [RFC2205].  It supports
   receiver-initiated establishment of resource reservations for both
   multicast and unicast flows.  RSVP was originally developed as a
   signaling protocol within the Integrated Services framework (see
   Section 5.1.1.1) for applications to communicate QoS requirements to
   the network and for the network to reserve relevant resources to
   satisfy the QoS requirements [RFC2205].

   In RSVP, the traffic sender or source node sends a Path message to
   the traffic receiver with the same source and destination addresses
   as the traffic that the sender will generate.  The Path message
   contains:

   *  A sender traffic specification describing the characteristics of
      the traffic

   *  A sender template specifying the format of the traffic

   *  An optional advertisement specification that is used to support
      the concept of One Pass With Advertising (OPWA) [RFC2205]

   Every intermediate router along the path forwards the Path message to
   the next hop determined by the routing protocol.  Upon receiving a
   Path message, the receiver responds with a Resv message that includes
   a flow descriptor used to request resource reservations.  The Resv
   message travels to the sender or source node in the opposite
   direction along the path that the Path message traversed.  Every
   intermediate router along the path can reject or accept the
   reservation request of the Resv message.  If the request is rejected,
   the rejecting router will send an error message to the receiver, and
   the signaling process will terminate.  If the request is accepted,
   link bandwidth and buffer space are allocated for the flow, and the
   related flow state information is installed in the router.

   One of the issues with the original RSVP specification [RFC2205] was
   scalability.  This was because reservations were required for micro-
   flows, so that the amount of state maintained by network elements
   tended to increase linearly with the number of traffic flows.  These
   issues are described in [RFC2961], which also modifies and extends
   RSVP to mitigate the scaling problems to make RSVP a versatile
   signaling protocol for the Internet.  For example, RSVP has been
   extended to reserve resources for aggregation of flows [RFC3175], to
   set up MPLS explicit LSPs (see Section 5.1.3.3), and to perform other
   signaling functions within the Internet.  [RFC2961] also describes a
   mechanism to reduce the amount of Refresh messages required to
   maintain established RSVP sessions.

5.1.3.3.  MPLS

   MPLS is a forwarding scheme that also includes extensions to
   conventional IP control plane protocols.  MPLS extends the Internet
   routing model and enhances packet forwarding and path control
   [RFC3031].

   At the ingress to an MPLS domain, LSRs classify IP packets into
   Forwarding Equivalence Classes (FECs) based on a variety of factors,
   including, e.g., a combination of the information carried in the IP
   header of the packets and the local routing information maintained by
   the LSRs.  An MPLS label stack entry is then prepended to each packet
   according to their FECs.  The MPLS label stack entry is 32 bits long
   and contains a 20-bit label field.

   An LSR makes forwarding decisions by using the label prepended to
   packets as the index into a local Next Hop Label Forwarding Entry
   (NHLFE).  The packet is then processed as specified in the NHLFE.
   The incoming label may be replaced by an outgoing label (label swap),
   and the packet may be forwarded to the next LSR.  Before a packet
   leaves an MPLS domain, its MPLS label may be removed (label pop).  An
   LSP is the path between an ingress LSR and an egress LSR through
   which a labeled packet traverses.  The path of an explicit LSP is
   defined at the originating (ingress) node of the LSP.  MPLS can use a
   signaling protocol such as RSVP or the Label Distribution Protocol
   (LDP) to set up LSPs.

   MPLS is a powerful technology for Internet TE because it supports
   explicit LSPs that allow constraint-based routing to be implemented
   efficiently in IP networks [AWD2].  The requirements for TE over MPLS
   are described in [RFC2702].  Extensions to RSVP to support
   instantiation of explicit LSP are discussed in [RFC3209] and
   Section 5.1.3.4.

5.1.3.4.  RSVP-TE

   RSVP-TE is a protocol extension of RSVP (Section 5.1.3.2) for traffic
   engineering.  The base specification is found in [RFC3209].  RSVP-TE
   enables the establishment of traffic-engineered MPLS LSPs (TE LSPs),
   using loose or strict paths and taking into consideration network
   constraints such as available bandwidth.  The extension supports
   signaling LSPs on explicit paths that could be administratively
   specified or computed by a suitable entity (such as a PCE,
   Section 5.1.3.11) based on QoS and policy requirements, taking into
   consideration the prevailing network state as advertised by the IGP
   extension for IS-IS in [RFC5305], for OSPFv2 in [RFC3630], and for
   OSPFv3 in [RFC5329].  RSVP-TE enables the reservation of resources
   (for example, bandwidth) along the path.

   RSVP-TE includes the ability to preempt LSPs based on priorities and
   uses link affinities to include or exclude links from the LSPs.  The
   protocol is further extended to support Fast Reroute (FRR) [RFC4090],
   Diffserv [RFC4124], and bidirectional LSPs [RFC7551].  RSVP-TE
   extensions for support for GMPLS (see Section 5.1.3.5) are specified
   in [RFC3473].

   Requirements for point-to-multipoint (P2MP) MPLS-TE LSPs are
   documented in [RFC4461], and signaling protocol extensions for
   setting up P2MP MPLS-TE LSPs via RSVP-TE are defined in [RFC4875],
   where a P2MP LSP comprises multiple source-to-leaf (S2L) sub-LSPs.
   To determine the paths for P2MP LSPs, selection of the branch points
   (based on capabilities, network state, and policies) is key [RFC5671]

   RSVP-TE has evolved to provide real-time dynamic metrics for path
   selection for low-latency paths using extensions to IS-IS [RFC8570]
   and OSPF [RFC7471] based on performance measurements for the Simple
   Two-Way Active Measurement Protocol (STAMP) [RFC8972] and the Two-Way
   Active Measurement Protocol (TWAMP) [RFC5357].

   RSVP-TE has historically been used when bandwidth was constrained;
   however, as bandwidth has increased, RSVP-TE has developed into a
   bandwidth management tool to provide bandwidth efficiency and
   proactive resource management.

5.1.3.5.  Generalized MPLS (GMPLS)

   GMPLS extends MPLS control protocols to encompass time-division
   (e.g., Synchronous Optical Network / Synchronous Digital Hierarchy
   (SONET/SDH), Plesiochronous Digital Hierarchy (PDH), and Optical
   Transport Network (OTN)), wavelength (lambdas), and spatial switching
   (e.g., incoming port or fiber to outgoing port or fiber) and
   continues to support packet switching.  GMPLS provides a common set
   of control protocols for all of these layers (including some
   technology-specific extensions), each of which has a distinct data or
   forwarding plane.  GMPLS covers both the signaling and the routing
   part of that control plane and is based on the TE extensions to MPLS
   (see Section 5.1.3.4).

   In GMPLS [RFC3945], the original MPLS architecture is extended to
   include LSRs whose forwarding planes rely on circuit switching and
   therefore cannot forward data based on the information carried in
   either packet or cell headers.  Specifically, such LSRs include
   devices where the switching is based on time slots, wavelengths, or
   physical ports.  These additions impact basic LSP properties: how
   labels are requested and communicated, the unidirectional nature of
   MPLS LSPs, how errors are propagated, and information provided for
   synchronizing the ingress and egress LSRs [RFC3473].

5.1.3.6.  IP Performance Metrics (IPPM)

   The IETF IP Performance Metrics (IPPM) Working Group has developed a
   set of standard metrics that can be used to monitor the quality,
   performance, and reliability of Internet services.  These metrics can
   be applied by network operators, end users, and independent testing
   groups to provide users and service providers with a common
   understanding of the performance and reliability of the Internet
   component clouds they use/provide [RFC2330].  The criteria for
   performance metrics developed by the IPPM Working Group are described
   in [RFC2330].  Examples of performance metrics include one-way packet
   loss [RFC7680], one-way delay [RFC7679], and connectivity measures
   between two nodes [RFC2678].  Other metrics include second-order
   measures of packet loss and delay.

   Some of the performance metrics specified by the IPPM Working Group
   are useful for specifying SLAs.  SLAs are sets of SLOs negotiated
   between users and service providers, wherein each objective is a
   combination of one or more performance metrics, possibly subject to
   certain constraints.

   The IPPM Working Group also designs measurement techniques and
   protocols to obtain these metrics.

5.1.3.7.  Flow Measurement

   The IETF Real Time Flow Measurement (RTFM) Working Group produced an
   architecture that defines a method to specify traffic flows as well
   as a number of components for flow measurement (meters, meter
   readers, and managers) [RFC2722].  A flow measurement system enables
   network traffic flows to be measured and analyzed at the flow level
   for a variety of purposes.  As noted in [RFC2722], a flow measurement
   system can be very useful in the following contexts:

   *  understanding the behavior of existing networks

   *  planning for network development and expansion

   *  quantification of network performance

   *  verifying the quality of network service

   *  attribution of network usage to users

   A flow measurement system consists of meters, meter readers, and
   managers.  A meter observes packets passing through a measurement
   point, classifies them into groups, accumulates usage data (such as
   the number of packets and bytes for each group), and stores the usage
   data in a flow table.  A group may represent any collection of user
   applications, hosts, networks, etc.  A meter reader gathers usage
   data from various meters so it can be made available for analysis.  A
   manager is responsible for configuring and controlling meters and
   meter readers.  The instructions received by a meter from a manager
   include flow specifications, meter control parameters, and sampling
   techniques.  The instructions received by a meter reader from a
   manager include the address of the meter whose data are to be
   collected, the frequency of data collection, and the types of flows
   to be collected.

   IP Flow Information Export (IPFIX) [RFC5470] defines an architecture
   that is very similar to the RTFM architecture and includes Metering,
   Exporting, and Collecting Processes.  [RFC5472] describes the
   applicability of IPFIX and makes a comparison with RTFM, pointing out
   that, architecturally, while RTM talks about devices, IPFIX deals
   with processes to clarify that multiple of those processes may be co-
   located on the same machine.  The IPFIX protocol [RFC7011] is widely
   implemented.

5.1.3.8.  Endpoint Congestion Management

   [RFC3124] provides a set of congestion control mechanisms for the use
   of transport protocols.  It also allows the development of mechanisms
   for unifying congestion control across a subset of an endpoint's
   active unicast connections (called a "congestion group").  A
   congestion manager continuously monitors the state of the path for
   each congestion group under its control.  The manager uses that
   information to instruct a scheduler on how to partition bandwidth
   among the connections of that congestion group.

   The concepts described in [RFC3124] and the lessons that can be
   learned from that work found a home in HTTP/2 [RFC9113] and QUIC
   [RFC9000], while [RFC9040] describes TCP control block
   interdependence that is a core construct underpinning the congestion
   manager defined in [RFC3124].

5.1.3.9.  TE Extensions to the IGPs

   [RFC5305] describes the extensions to the Intermediate System to
   Intermediate System (IS-IS) protocol to support TE.  Similarly,
   [RFC3630] specifies TE extensions for OSPFv2, and [RFC5329] has the
   same description for OSPFv3.

   IS-IS and OSPF share the common concept of TE extensions to
   distribute TE parameters, such as link type and ID, local and remote
   IP addresses, TE metric, maximum bandwidth, maximum reservable
   bandwidth, unreserved bandwidth, and admin group.  The information
   distributed by the IGPs in this way can be used to build a view of
   the state and capabilities of a TE network (see Section 5.1.3.14).

   The difference between IS-IS and OSPF is in the details of how they
   encode and transmit the TE parameters:

   *  IS-IS uses the Extended IS Reachability TLV (type 22), the
      Extended IP Reachability TLV (type 135), and the Traffic
      Engineering router ID TLV (type 134).  These TLVs use specific
      sub-TLVs described in [RFC8570] to carry the TE parameters.

   *  OSPFv2 uses Opaque LSA [RFC5250] type 10, and OSPFv3 uses the
      Intra-Area-TE-LSA.  In both OSPF cases, two top-level TLVs are
      used (Router Address and Link TLVs), and these use sub-TLVs to
      carry the TE parameters (as defined in [RFC7471] for OSPFv2 and
      [RFC5329] for OSPFv3).

5.1.3.10.  BGP - Link State

   In a number of environments, a component external to a network is
   called upon to perform computations based on the network topology and
   current state of the connections within the network, including TE
   information.  This is information typically distributed by IGP
   routing protocols within the network (see Section 5.1.3.9).

   BGP (see also Section 7) is one of the essential routing protocols
   that glues the Internet together.  BGP-LS [RFC9552] is a mechanism by
   which link-state and TE information can be collected from networks
   and shared with external components using the BGP routing protocol.
   The mechanism is applicable to physical and virtual IGP links and is
   subject to policy control.

   Information collected by BGP-LS can be used, for example, to
   construct the TED (Section 5.1.3.14) for use by the PCE (see
   Section 5.1.3.11) or may be used by ALTO servers (see
   Section 5.1.2.1).

5.1.3.11.  Path Computation Element

   Constraint-based path computation is a fundamental building block for
   TE in MPLS and GMPLS networks.  Path computation in large, multi-
   domain networks is complex and may require special computational
   components and cooperation between the elements in different domains.
   The PCE [RFC4655] is an entity (component, application, or network
   node) that is capable of computing a network path or route based on a
   network graph and applying computational constraints.

   Thus, a PCE can provide a central component in a TE system operating
   on the TED (see Section 5.1.3.14) with delegated responsibility for
   determining paths in MPLS, GMPLS, or SR networks.  The PCE uses the
   Path Computation Element Communication Protocol (PCEP) [RFC5440] to
   communicate with Path Computation Clients (PCCs), such as MPLS LSRs,
   to answer their requests for computed paths or to instruct them to
   initiate new paths [RFC8281] and maintain state about paths already
   installed in the network [RFC8231].

   PCEs form key components of a number of TE systems.  More information
   about the applicability of PCEs can be found in [RFC8051], while
   [RFC6805] describes the application of PCEs to determining paths
   across multiple domains.  PCEs also have potential uses in
   Abstraction and Control of TE Networks (ACTN) (see Section 5.1.2.2),
   Centralized Network Control [RFC8283], and SDN (see Section 4.3.2).

5.1.3.12.  Segment Routing (SR)

   The SR architecture [RFC8402] leverages the source routing and
   tunneling paradigms.  The path a packet takes is defined at the
   ingress, and the packet is tunneled to the egress.

   In a protocol realization, an ingress node steers a packet using a
   set of instructions, called "segments", that are included in an SR
   header prepended to the packet: a label stack in MPLS case, and a
   series of 128-bit SIDs in the IPv6 case.

   Segments are identified by SIDs.  There are four types of SIDs that
   are relevant for TE.

   *  Prefix SID: A SID that is unique within the routing domain and is
      used to identify a prefix.

   *  Node SID: A Prefix SID with the "N" bit set to identify a node.

   *  Adjacency SID: Identifies a unidirectional adjacency.

   *  Binding SID: A Binding SID has two purposes:

      1.  To advertise the mappings of prefixes to SIDs/Labels

      2.  To advertise a path available for a Forwarding Equivalence
          Class (FEC)

   A segment can represent any instruction, topological or service-
   based.  SIDs can be looked up in a global context (domain-wide) as
   well as in some other contexts (see, for example, "context labels" in
   Section 3 of [RFC5331]).

   The application of policy to SR can make SR into a TE mechanism, as
   described in Section 5.1.1.3.

5.1.3.13.  Tree Engineering for Bit Index Explicit Replication

   Bit Index Explicit Replication (BIER) [RFC8279] specifies an
   encapsulation for multicast forwarding that can be used on MPLS or
   Ethernet transports.  A mechanism known as Tree Engineering for Bit
   Index Explicit Replication (BIER-TE) [RFC9262] provides a component
   that could be used to build a traffic-engineered multicast system.
   BIER-TE does not of itself offer full traffic engineering, and the
   abbreviation "TE" does not, in this case, refer to traffic
   engineering.

   In BIER-TE, path steering is supported via the definition of a
   bitstring attached to each packet that determines how the packet is
   forwarded and replicated within the network.  Thus, this bitstring
   steers the traffic within the network and forms an element of a
   traffic-engineering system.  A central controller that is aware of
   the capabilities and state of the network as well as the demands of
   the various traffic flows is able to select multicast paths that take
   account of the available resources and demands.  Therefore, this
   controller is responsible for the policy elements of traffic
   engineering.

   Resource management has implications for the forwarding plane beyond
   the steering of packets defined for BIER-TE.  These include the
   allocation of buffers to meet the requirements of admitted traffic
   and may include policing and/or rate-shaping mechanisms achieved via
   various forms of queuing.  This level of resource control, while
   optional, is important in networks that wish to support congestion
   management policies to control or regulate the offered traffic to
   deliver different levels of service and alleviate congestion
   problems.  It is also important in networks that wish to control
   latencies experienced by specific traffic flows.

5.1.3.14.  Network TE State Definition and Presentation

   The network states that are relevant to TE need to be stored in the
   system and presented to the user.  The TED is a collection of all TE
   information about all TE nodes and TE links in the network.  It is an
   essential component of a TE system, such as MPLS-TE [RFC2702] or
   GMPLS [RFC3945].  In order to formally define the data in the TED and
   to present the data to the user, the data modeling language YANG
   [RFC7950] can be used as described in [RFC8795].

5.1.3.15.  System Management and Control Interfaces

   The TE control system needs to have a management interface that is
   human-friendly and a control interface that is programmable for
   automation.  The Network Configuration Protocol (NETCONF) [RFC6241]
   and the RESTCONF protocol [RFC8040] provide programmable interfaces
   that are also human-friendly.  These protocols use XML- or JSON-
   encoded messages.  When message compactness or protocol bandwidth
   consumption needs to be optimized for the control interface, other
   protocols, such as Group Communication for the Constrained
   Application Protocol (CoAP) [RFC7390] or gRPC [GRPC], are available,
   especially when the protocol messages are encoded in a binary format.
   Along with any of these protocols, the data modeling language YANG
   [RFC7950] can be used to formally and precisely define the interface
   data.

   PCEP [RFC5440] is another protocol that has evolved to be an option
   for the TE system control interface.  PCEP messages are TLV based;
   they are not defined by a data-modeling language such as YANG.

5.2.  Content Distribution

   The Internet is dominated by client-server interactions, principally
   web traffic and multimedia streams, although in the future, more
   sophisticated media servers may become dominant.  The location and
   performance of major information servers have a significant impact on
   the traffic patterns within the Internet as well as on the perception
   of service quality by end users.

   A number of dynamic load-balancing techniques have been devised to
   improve the performance of replicated information servers.  These
   techniques can cause spatial traffic characteristics to become more
   dynamic in the Internet because information servers can be
   dynamically picked based upon the location of the clients, the
   location of the servers, the relative utilization of the servers, the
   relative performance of different networks, and the relative
   performance of different parts of a network.  This process of
   assignment of distributed servers to clients is called "traffic
   directing".  It is an application-layer function.

   Traffic-directing schemes that allocate servers in multiple
   geographically dispersed locations to clients may require empirical
   network performance statistics to make more effective decisions.  In
   the future, network measurement systems may need to provide this type
   of information.

   When congestion exists in the network, traffic-directing and traffic-
   engineering systems should act in a coordinated manner.  This topic
   is for further study.

   The issues related to location and replication of information
   servers, particularly web servers, are important for Internet traffic
   engineering because these servers contribute a substantial proportion
   of Internet traffic.

6.  Recommendations for Internet Traffic Engineering

   This section describes high-level recommendations for traffic
   engineering in the Internet in general terms.

   The recommendations describe the capabilities needed to solve a TE
   problem or to achieve a TE objective.  Broadly speaking, these
   recommendations can be categorized as either functional or non-
   functional recommendations:

   *  Functional recommendations describe the functions that a traffic-
      engineering system should perform.  These functions are needed to
      realize TE objectives by addressing traffic-engineering problems.

   *  Non-functional recommendations relate to the quality attributes or
      state characteristics of a TE system.  These recommendations may
      contain conflicting assertions and may sometimes be difficult to
      quantify precisely.

   The subsections that follow first summarize the non-functional
   requirements and then detail the functional requirements.

6.1.  Generic Non-functional Recommendations

   The generic non-functional recommendations for Internet traffic
   engineering are listed in the paragraphs that follow.  In a given
   context, some of these recommendations may be critical while others
   may be optional.  Therefore, prioritization may be required during
   the development phase of a TE system to tailor it to a specific
   operational context.

   Automation:  Whenever feasible, a TE system should automate as many
      TE functions as possible to minimize the amount of human effort
      needed to analyze and control operational networks.  Automation is
      particularly important in large-scale public networks because of
      the high cost of the human aspects of network operations and the
      high risk of network problems caused by human errors.  Automation
      may additionally benefit from feedback from the network that
      indicates the state of network resources and the current load in
      the network.  Further, placing intelligence into components of the
      TE system could enable automation to be more dynamic and
      responsive to changes in the network.

   Flexibility:  A TE system should allow for changes in optimization
      policy.  In particular, a TE system should provide sufficient
      configuration options so that a network administrator can tailor
      the system to a particular environment.  It may also be desirable
      to have both online and offline TE subsystems that can be
      independently enabled and disabled.  TE systems that are used in
      multi-class networks should also have options to support class-
      based performance evaluation and optimization.

   Interoperability:  Whenever feasible, TE systems and their components
      should be developed with open standards-based interfaces to allow
      interoperation with other systems and components.

   Scalability:  Public networks continue to grow rapidly with respect
      to network size and traffic volume.  Therefore, to remain
      applicable as the network evolves, a TE system should be scalable.
      In particular, a TE system should remain functional as the network
      expands with regard to the number of routers and links and with
      respect to the number of flows and the traffic volume.  A TE
      system should have a scalable architecture, should not adversely
      impair other functions and processes in a network element, and
      should not consume too many network resources when collecting and
      distributing state information or when exerting control.

   Security:  Security is a critical consideration in TE systems.  Such
      systems typically exert control over functional aspects of the
      network to achieve the desired performance objectives.  Therefore,
      adequate measures must be taken to safeguard the integrity of the
      TE system.  Adequate measures must also be taken to protect the
      network from vulnerabilities that originate from security breaches
      and other impairments within the TE system.

   Simplicity:  A TE system should be as simple as possible.  Simplicity
      in user interface does not necessarily imply that the TE system
      will use naive algorithms.  When complex algorithms and internal
      structures are used, the user interface should hide such
      complexities from the network administrator as much as possible.

   Stability:  Stability refers to the resistance of the network to
      oscillate (flap) in a disruptive manner from one state to another,
      which may result in traffic being routed first one way and then
      another without satisfactory resolution of the underlying TE
      issues and with continued changes that do not settle down.
      Stability is a very important consideration in TE systems that
      respond to changes in the state of the network.  State-dependent
      TE methodologies typically include a trade-off between
      responsiveness and stability.  It is strongly recommended that
      when a trade-off between responsiveness and stability is needed,
      it should be made in favor of stability (especially in public IP
      backbone networks).

   Usability:  Usability is a human aspect of TE systems.  It refers to
      the ease with which a TE system can be deployed and operated.  In
      general, it is desirable to have a TE system that can be readily
      deployed in an existing network.  It is also desirable to have a
      TE system that is easy to operate and maintain.

   Visibility:  Mechanisms should exist as part of the TE system to
      collect statistics from the network and to analyze these
      statistics to determine how well the network is functioning.
      Derived statistics (such as traffic matrices, link utilization,
      latency, packet loss, and other performance measures of interest)
      that are determined from network measurements can be used as
      indicators of prevailing network conditions.  The capabilities of
      the various components of the routing system are other examples of
      status information that should be observable.

6.2.  Routing Recommendations

   Routing control is a significant aspect of Internet traffic
   engineering.  Routing impacts many of the key performance measures
   associated with networks, such as throughput, delay, and utilization.
   Generally, it is very difficult to provide good service quality in a
   wide area network without effective routing control.  A desirable TE
   routing system is one that takes traffic characteristics and network
   constraints into account during route selection while maintaining
   stability.

   Shortest Path First (SPF) IGPs are based on shortest path algorithms
   and have limited control capabilities for TE [RFC2702] [AWD2].  These
   limitations include:

   1.  Pure SPF protocols do not take network constraints and traffic
       characteristics into account during route selection.  For
       example, IGPs always select the shortest paths based on link
       metrics assigned by administrators, so load sharing cannot be
       performed across paths of different costs.  Note that link
       metrics are assigned following a range of operator-selected
       policies that might reflect preference for the use of some links
       over others; therefore, "shortest" might not be purely a measure
       of distance.  Using shortest paths to forward traffic may cause
       the following problems:

       *  If traffic from a source to a destination exceeds the capacity
          of a link along the shortest path, the link (and hence the
          shortest path) becomes congested while a longer path between
          these two nodes may be under-utilized.

       *  The shortest paths from different sources can overlap at some
          links.  If the total traffic from the sources exceeds the
          capacity of any of these links, congestion will occur.

       *  Problems can also occur because traffic demand changes over
          time, but network topology and routing configuration cannot be
          changed as rapidly.  This causes the network topology and
          routing configuration to become sub-optimal over time, which
          may result in persistent congestion problems.

   2.  The Equal-Cost Multipath (ECMP) capability of SPF IGPs supports
       sharing of traffic among equal-cost paths.  However, ECMP
       attempts to divide the traffic as equally as possible among the
       equal-cost shortest paths.  Generally, ECMP does not support
       configurable load-sharing ratios among equal-cost paths.  The
       result is that one of the paths may carry significantly more
       traffic than other paths because it may also carry traffic from
       other sources.  This situation can result in congestion along the
       path that carries more traffic.  Weighted ECMP (WECMP) (see, for
       example, [EVPN-UNEQUAL-LB]) provides some mitigation.

   3.  Modifying IGP metrics to control traffic routing tends to have
       network-wide effects.  Consequently, undesirable and
       unanticipated traffic shifts can be triggered as a result.  Work
       described in Section 8 may be capable of better control [FT00]
       [FT01].

   Because of these limitations, capabilities are needed to enhance the
   routing function in IP networks.  Some of these capabilities are
   summarized below:

   *  Constraint-based routing computes routes to fulfill requirements
      subject to constraints.  This can be useful in public IP backbones
      with complex topologies.  Constraints may include bandwidth, hop
      count, delay, and administrative policy instruments, such as
      resource class attributes [RFC2702] [RFC2386].  This makes it
      possible to select routes that satisfy a given set of
      requirements.  Routes computed by constraint-based routing are not
      necessarily the shortest paths.  Constraint-based routing works
      best with path-oriented technologies that support explicit
      routing, such as MPLS.

   *  Constraint-based routing can also be used as a way to distribute
      traffic onto the infrastructure, including for best-effort
      traffic.  For example, congestion problems caused by uneven
      traffic distribution may be avoided or reduced by knowing the
      reservable bandwidth attributes of the network links and by
      specifying the bandwidth requirements for path selection.

   *  A number of enhancements to the link-state IGPs allow them to
      distribute additional state information required for constraint-
      based routing.  The extensions to OSPF are described in [RFC3630],
      and the extensions to IS-IS are described in [RFC5305].  Some of
      the additional topology state information includes link
      attributes, such as reservable bandwidth and link resource class
      attribute (an administratively specified property of the link).
      The resource class attribute concept is defined in [RFC2702].  The
      additional topology state information is carried in new TLVs and
      sub-TLVs in IS-IS [RFC5305] or in the Opaque LSA in OSPF
      [RFC3630].

   *  An enhanced link-state IGP may flood information more frequently
      than a normal IGP.  This is because even without changes in
      topology, changes in reservable bandwidth or link affinity can
      trigger the enhanced IGP to initiate flooding.  A trade-off
      between the timeliness of the information flooded and the flooding
      frequency is typically implemented using a threshold based on the
      percentage change of the advertised resources to avoid excessive
      consumption of link bandwidth and computational resources and to
      avoid instability in the TED.

   *  In a TE system, it is also desirable for the routing subsystem to
      make the load-splitting ratio among multiple paths (with equal
      cost or different cost) configurable.  This capability gives
      network administrators more flexibility in the control of traffic
      distribution across the network.  It can be very useful for
      avoiding/relieving congestion in certain situations.  Examples can
      be found in [XIAO] and [EVPN-UNEQUAL-LB].

   *  The routing system should also have the capability to control the
      routes of subsets of traffic without affecting the routes of other
      traffic if sufficient resources exist for this purpose.  This
      capability allows a more refined control over the distribution of
      traffic across the network.  For example, the ability to move
      traffic away from its original path to another path (without
      affecting other traffic paths) allows the traffic to be moved from
      resource-poor network segments to resource-rich segments.  Path-
      oriented technologies, such as MPLS-TE, inherently support this
      capability as discussed in [AWD2].

   *  Additionally, the routing subsystem should be able to select
      different paths for different classes of traffic (or for different
      traffic behavior aggregates) if the network supports multiple
      classes of service (different behavior aggregates).

6.3.  Traffic Mapping Recommendations

   Traffic mapping is the assignment of traffic workload onto (pre-
   established) paths to meet certain requirements.  Thus, while
   constraint-based routing deals with path selection, traffic mapping
   deals with the assignment of traffic to established paths that may
   have been generated by constraint-based routing or by some other
   means.  Traffic mapping can be performed by time-dependent or state-
   dependent mechanisms, as described in Section 4.1.

   Two important aspects of the traffic mapping function are the ability
   to establish multiple paths between an originating node and a
   destination node and the capability to distribute the traffic across
   those paths according to configured policies.  A precondition for
   this scheme is the existence of flexible mechanisms to partition
   traffic and then assign the traffic partitions onto the parallel
   paths (described as "parallel traffic trunks" in [RFC2702]).  When
   traffic is assigned to multiple parallel paths, it is recommended
   that special care should be taken to ensure proper ordering of
   packets belonging to the same application (or traffic flow) at the
   destination node of the parallel paths.

   Mechanisms that perform the traffic mapping functions should aim to
   map the traffic onto the network infrastructure to minimize
   congestion.  If the total traffic load cannot be accommodated, or if
   the routing and mapping functions cannot react fast enough to
   changing traffic conditions, then a traffic mapping system may use
   short timescale congestion control mechanisms (such as queue
   management, scheduling, etc.) to mitigate congestion.  Thus,
   mechanisms that perform the traffic mapping functions complement
   existing congestion control mechanisms.  In an operational network,
   traffic should be mapped onto the infrastructure such that intra-
   class and inter-class resource contention are minimized (see
   Section 2).

   When traffic mapping techniques that depend on dynamic state feedback
   (e.g., MPLS Adaptive Traffic Engineering (MATE) [MATE] and suchlike)
   are used, special care must be taken to guarantee network stability.

6.4.  Measurement Recommendations

   The importance of measurement in TE has been discussed throughout
   this document.  A TE system should include mechanisms to measure and
   collect statistics from the network to support the TE function.
   Additional capabilities may be needed to help in the analysis of the
   statistics.  The actions of these mechanisms should not adversely
   affect the accuracy and integrity of the statistics collected.  The
   mechanisms for statistical data acquisition should also be able to
   scale as the network evolves.

   Traffic statistics may be classified according to long-term or short-
   term timescales.  Long-term traffic statistics are very useful for
   traffic engineering.  Long-term traffic statistics may periodically
   record network workload (such as hourly, daily, and weekly variations
   in traffic profiles) as well as traffic trends.  Aspects of the
   traffic statistics may also describe class of service characteristics
   for a network supporting multiple classes of service.  Analysis of
   the long-term traffic statistics may yield other information such as
   busy-hour characteristics, traffic growth patterns, persistent
   congestion problems, hotspots, and imbalances in link utilization
   caused by routing anomalies.

   A mechanism for constructing traffic matrices for both long-term and
   short-term traffic statistics should be in place.  In multi-service
   IP networks, the traffic matrices may be constructed for different
   service classes.  Each element of a traffic matrix represents a
   statistic about the traffic flow between a pair of abstract nodes.
   An abstract node may represent a router, a collection of routers, or
   a site in a VPN.

   Traffic statistics should provide reasonable and reliable indicators
   of the current state of the network on the short-term scale.  Some
   short-term traffic statistics may reflect link utilization and link
   congestion status.  Examples of congestion indicators include
   excessive packet delay, packet loss, and high resource utilization.
   Examples of mechanisms for distributing this kind of information
   include SNMP, probing tools, FTP, IGP link-state advertisements,
   NETCONF/RESTCONF, etc.

6.5.  Policing, Planning, and Access Control

   The recommendations in Sections 6.2 and 6.3 may be sub-optimal or
   even ineffective if the amount of traffic flowing on a route or path
   exceeds the capacity of the resource on that route or path.  Several
   approaches can be used to increase the performance of TE systems:

   *  The fundamental approach is some form of planning where traffic is
      steered onto paths so that it is distributed across the available
      resources.  This planning may be centralized or distributed and
      must be aware of the planned traffic volumes and available
      resources.  However, this approach is only of value if the traffic
      that is presented conforms to the planned traffic volumes.

   *  Traffic flows may be policed at the edges of a network.  This is a
      simple way to ensure that the actual traffic volumes are
      consistent with the planned volumes.  Some form of measurement
      (see Section 6.4) is used to determine the rate of arrival of
      traffic, and excess traffic could be discarded.  Alternatively,
      excess traffic could be forwarded as best-effort within the
      network.  However, this approach is only completely effective if
      the planning is stringent and network-wide and if a harsh approach
      is taken to disposing of excess traffic.

   *  Resource-based admission control is the process whereby network
      nodes decide whether to grant access to resources.  The basis for
      the decision on a packet-by-packet basis is the determination of
      the flow to which the packet belongs.  This information is
      combined with policy instructions that have been locally
      configured or installed through the management or control planes.
      The end result is that a packet may be allowed to access (or use)
      specific resources on the node if, and only if, the flow to which
      the packet belongs conforms to the policy.

   Combining some elements of all three of these measures is advisable
   to achieve a better TE system.

6.6.  Network Survivability

   Network survivability refers to the capability of a network to
   maintain service continuity in the presence of faults.  This can be
   accomplished by promptly recovering from network impairments and
   maintaining the required QoS for existing services after recovery.
   Survivability is an issue of great concern within the Internet
   community due to the demand to carry mission-critical traffic, real-
   time traffic, and other high-priority traffic over the Internet.
   Survivability can be addressed at the device level by developing
   network elements that are more reliable and at the network level by
   incorporating redundancy into the architecture, design, and operation
   of networks.  It is recommended that a philosophy of robustness and
   survivability should be adopted in the architecture, design, and
   operation of TE used to control IP networks (especially public IP
   networks).  Because different contexts may demand different levels of
   survivability, the mechanisms developed to support network
   survivability should be flexible so that they can be tailored to
   different needs.  A number of tools and techniques have been
   developed to enable network survivability, including MPLS Fast
   Reroute [RFC4090], Topology Independent Loop-free Alternate Fast
   Reroute for Segment Routing [SR-TI-LFA], RSVP-TE Extensions in
   Support of End-to-End GMPLS Recovery [RFC4872], and GMPLS Segment
   Recovery [RFC4873].

   The impact of service outages varies significantly for different
   service classes depending on the duration of the outage, which can
   vary from milliseconds (with minor service impact) to seconds (with
   possible call drops for IP telephony and session timeouts for
   connection-oriented transactions) to minutes and hours (with
   potentially considerable social and business impact).  Outages of
   different durations have different impacts depending on the nature of
   the traffic flows that are interrupted.

   Failure protection and restoration capabilities are available in
   multiple layers as network technologies have continued to evolve.
   Optical networks are capable of providing dynamic ring and mesh
   restoration functionality at the wavelength level.  At the SONET/SDH
   layer, survivability capability is provided with Automatic Protection
   Switching (APS) as well as self-healing ring and mesh architectures.
   Similar functionality is provided by Layer 2 technologies such as
   Ethernet.

   Rerouting is used at the IP layer to restore service following link
   and node outages.  Rerouting at the IP layer occurs after a period of
   routing convergence, which may require seconds to minutes to
   complete.  Path-oriented technologies such as MPLS [RFC3469] can be
   used to enhance the survivability of IP networks in a potentially
   cost-effective manner.

   An important aspect of multi-layer survivability is that technologies
   at different layers may provide protection and restoration
   capabilities at different granularities in terms of timescales and at
   different bandwidth granularities (from the level of packets to that
   of wavelengths).  Protection and restoration capabilities can also be
   sensitive to different service classes and different network utility
   models.  Coordinating different protection and restoration
   capabilities across multiple layers in a cohesive manner to ensure
   network survivability is maintained at reasonable cost is a
   challenging task.  Protection and restoration coordination across
   layers may not always be feasible, because networks at different
   layers may belong to different administrative domains.

   Some of the general recommendations for protection and restoration
   coordination are as follows:

   *  Protection and restoration capabilities from different layers
      should be coordinated to provide network survivability in a
      flexible and cost-effective manner.  Avoiding duplication of
      functions in different layers is one way to achieve the
      coordination.  Escalation of alarms and other fault indicators
      from lower to higher layers may also be performed in a coordinated
      manner.  The order of timing of restoration triggers from
      different layers is another way to coordinate multi-layer
      protection/restoration.

   *  Network capacity reserved in one layer to provide protection and
      restoration is not available to carry traffic in a higher layer:
      it is not visible as spare capacity in the higher layer.  Placing
      protection/restoration functions in many layers may increase
      redundancy and robustness, but it can result in significant
      inefficiencies in network resource utilization.  Careful planning
      is needed to balance the trade-off between the desire for
      survivability and the optimal use of resources.

   *  It is generally desirable to have protection and restoration
      schemes that are intrinsically bandwidth efficient.

   *  Failure notifications throughout the network should be timely and
      reliable if they are to be acted on as triggers for effective
      protection and restoration actions.

   *  Alarms and other fault monitoring and reporting capabilities
      should be provided at the right network layers so that the
      protection and restoration actions can be taken in those layers.

6.6.1.  Survivability in MPLS-Based Networks

   Because MPLS is path-oriented, it has the potential to provide faster
   and more predictable protection and restoration capabilities than
   conventional hop-by-hop routed IP systems.  Protection types for MPLS
   networks can be divided into four categories:

   Link Protection:  The objective of link protection is to protect an
      LSP from the failure of a given link.  Under link protection, a
      protection or backup LSP (the secondary LSP) follows a path that
      is disjoint from the path of the working or operational LSP (the
      primary LSP) at the particular link where link protection is
      required.  When the protected link fails, traffic on the working
      LSP is switched to the protection LSP at the headend of the failed
      link.  As a local repair method, link protection can be fast.
      This form of protection may be most appropriate in situations
      where some network elements along a given path are known to be
      less reliable than others.

   Node Protection:  The objective of node protection is to protect an
      LSP from the failure of a given node.  Under node protection, the
      secondary LSP follows a path that is disjoint from the path of the
      primary LSP at the particular node where node protection is
      required.  The secondary LSP is also disjoint from the primary LSP
      at all links attached to the node to be protected.  When the
      protected node fails, traffic on the working LSP is switched over
      to the protection LSP at the upstream LSR directly connected to
      the failed node.  Node protection covers a slightly larger part of
      the network compared to link protection but is otherwise
      fundamentally the same.

   Path Protection:  The goal of LSP path protection (or end-to-end
      protection) is to protect an LSP from any failure along its routed
      path.  Under path protection, the path of the protection LSP is
      completely disjoint from the path of the working LSP.  The
      advantage of path protection is that the backup LSP protects the
      working LSP from all possible link and node failures along the
      path, except for failures of ingress or egress LSR.  Additionally,
      path protection may be more efficient in terms of resource usage
      than link or node protection applied at every hop along the path.
      However, path protection may be slower than link and node
      protection because the fault notifications have to be propagated
      further.

   Segment Protection:  An MPLS domain may be partitioned into multiple
      subdomains (protection domains).  Path protection is applied to
      the path of each LSP as it crosses the domain from its ingress to
      the domain to where it egresses the domain.  In cases where an LSP
      traverses multiple protection domains, a protection mechanism
      within a domain only needs to protect the segment of the LSP that
      lies within the domain.  Segment protection will generally be
      faster than end-to-end path protection because recovery generally
      occurs closer to the fault, and the notification doesn't have to
      propagate as far.

   See [RFC3469] and [RFC6372] for a more comprehensive discussion of
   MPLS-based recovery.

6.6.2.  Protection Options

   Another issue to consider is the concept of protection options.  We
   use notation such as "m:n protection", where m is the number of
   protection LSPs used to protect n working LSPs.  In all cases except
   1+1 protection, the resources associated with the protection LSPs can
   be used to carry preemptable best-effort traffic when the working LSP
   is functioning correctly.

   1:1 protection:  One working LSP is protected/restored by one
      protection LSP.  Traffic is sent only on the protected LSP until
      the protection/restoration event switches the traffic to the
      protection LSP.

   1:n protection:  One protection LSP is used to protect/restore n
      working LSPs.  Traffic is sent only on the n protected working
      LSPs until the protection/restoration event switches the traffic
      from one failed LSP to the protection LSP.  Only one failed LSP
      can be restored at any time.

   n:1 protection:  One working LSP is protected/restored by n
      protection LSPs, possibly with load splitting across the
      protection LSPs.  This may be especially useful when it is not
      feasible to find one path for the backup that can satisfy the
      bandwidth requirement of the primary LSP.

   1+1 protection:  Traffic is sent concurrently on both the working LSP
      and a protection LSP.  The egress LSR selects one of the two LSPs
      based on local policy (usually based on traffic integrity).  When
      a fault disrupts the traffic on one LSP, the egress switches to
      receive traffic from the other LSP.  This approach is expensive in
      how it consumes network but recovers from failures most rapidly.

6.7.  Multi-Layer Traffic Engineering

   Networks are often implemented as layers.  A layer relationship may
   represent the interaction between technologies (for example, an IP
   network operated over an optical network) or the relationship between
   different network operators (for example, a customer network operated
   over a service provider's network).  Note that a multi-layer network
   does not imply the use of multiple technologies, although some form
   of encapsulation is often applied.

   Multi-layer traffic engineering presents a number of challenges
   associated with scalability and confidentiality.  These issues are
   addressed in [RFC7926], which discusses the sharing of information
   between domains through policy filters, aggregation, abstraction, and
   virtualization.  That document also discusses how existing protocols
   can support this scenario with special reference to BGP-LS (see
   Section 5.1.3.10).

   PCE (see Section 5.1.3.11) is also a useful tool for multi-layer
   networks as described in [RFC6805], [RFC8685], and [RFC5623].
   Signaling techniques for multi-layer TE are described in [RFC6107].

   See also Section 6.6 for examination of multi-layer network
   survivability.

6.8.  Traffic Engineering in Diffserv Environments

   Increasing requirements to support multiple classes of traffic in the
   Internet, such as best-effort and mission-critical data, call for IP
   networks to differentiate traffic according to some criteria and to
   give preferential treatment to certain types of traffic.  Large
   numbers of flows can be aggregated into a few behavior aggregates
   based on some criteria based on common performance requirements in
   terms of packet loss ratio, delay, and jitter or in terms of common
   fields within the IP packet headers.

   Differentiated Services (Diffserv) [RFC2475] can be used to ensure
   that SLAs defined to differentiate between traffic flows are met.
   Classes of service can be supported in a Diffserv environment by
   concatenating Per-Hop Behaviors (PHBs) along the routing path.  A PHB
   is the forwarding behavior that a packet receives at a Diffserv-
   compliant node, and it can be configured at each router.  PHBs are
   delivered using buffer-management and packet-scheduling mechanisms
   and require that the ingress nodes use traffic classification,
   marking, policing, and shaping.

   TE can complement Diffserv to improve utilization of network
   resources.  TE can be operated on an aggregated basis across all
   service classes [RFC3270] or on a per-service-class basis.  The
   former is used to provide better distribution of the traffic load
   over the network resources (see [RFC3270] for detailed mechanisms to
   support aggregate TE).  The latter case is discussed below since it
   is specific to the Diffserv environment, with so-called Diffserv-
   aware traffic engineering [RFC4124].

   For some Diffserv networks, it may be desirable to control the
   performance of some service classes by enforcing relationships
   between the traffic workload contributed by each service class and
   the amount of network resources allocated or provisioned for that
   service class.  Such relationships between demand and resource
   allocation can be enforced using a combination of, for example:

   *  TE mechanisms on a per-service-class basis that enforce the
      relationship between the amount of traffic contributed by a given
      service class and the resources allocated to that class.

   *  Mechanisms that dynamically adjust the resources allocated to a
      given service class to relate to the amount of traffic contributed
      by that service class.

   It may also be desirable to limit the performance impact of high-
   priority traffic on relatively low-priority traffic.  This can be
   achieved, for example, by controlling the percentage of high-priority
   traffic that is routed through a given link.  Another way to
   accomplish this is to increase link capacities appropriately so that
   lower-priority traffic can still enjoy adequate service quality.
   When the ratio of traffic workload contributed by different service
   classes varies significantly from router to router, it may not be
   enough to rely on conventional IGP routing protocols or on TE
   mechanisms that are not sensitive to different service classes.
   Instead, it may be desirable to perform TE, especially routing
   control and mapping functions, on a per-service-class basis.  One way
   to accomplish this in a domain that supports both MPLS and Diffserv
   is to define class-specific LSPs and to map traffic from each class
   onto one or more LSPs that correspond to that service class.  An LSP
   corresponding to a given service class can then be routed and
   protected/restored in a class-dependent manner, according to specific
   policies.

   Performing TE on a per-class basis may require per-class parameters
   to be distributed.  It is common to have some classes share some
   aggregate constraints (e.g., maximum bandwidth requirement) without
   enforcing the constraint on each individual class.  These classes can
   be grouped into class types, and per-class-type parameters can be
   distributed to improve scalability.  This also allows better
   bandwidth sharing between classes in the same class type.  A class
   type is a set of classes that satisfy the following two conditions:

   *  Classes in the same class type have common aggregate requirements
      to satisfy required performance levels.

   *  There is no requirement to be enforced at the level of an
      individual class in the class type.  Note that it is,
      nevertheless, still possible to implement some priority policies
      for classes in the same class type to permit preferential access
      to the class type bandwidth through the use of preemption
      priorities.

   See [RFC4124] for detailed requirements on Diffserv-aware TE.

6.9.  Network Controllability

   Offline and online (see Section 4.2) TE considerations are of limited
   utility if the network cannot be controlled effectively to implement
   the results of TE decisions and to achieve the desired network
   performance objectives.

   Capacity augmentation is a coarse-grained solution to TE issues.
   However, it is simple, may be applied through creating parallel links
   that form part of an ECMP scheme, and may be advantageous if
   bandwidth is abundant and cheap.  However, bandwidth is not always
   abundant and cheap, and additional capacity might not always be the
   best solution.  Adjustments of administrative weights and other
   parameters associated with routing protocols provide finer-grained
   control, but this approach is difficult to use and imprecise because
   of the way the routing protocols interact across the network.

   Control mechanisms can be manual (e.g., static configuration),
   partially automated (e.g., scripts), or fully automated (e.g.,
   policy-based management systems).  Automated mechanisms are
   particularly useful in large-scale networks.  Multi-vendor
   interoperability can be facilitated by standardized management tools
   (e.g., YANG models) to support the control functions required to
   address TE objectives.

   Network control functions should be secure, reliable, and stable as
   these are often needed to operate correctly in times of network
   impairments (e.g., during network congestion or attacks).

7.  Inter-Domain Considerations

   Inter-domain TE is concerned with performance optimization for
   traffic that originates in one administrative domain and terminates
   in a different one.

   BGP [RFC4271] is the standard exterior gateway protocol used to
   exchange routing information between ASes in the Internet.  BGP
   includes a decision process that calculates the preference for routes
   to a given destination network.  There are two fundamental aspects to
   inter-domain TE using BGP:

   Route Propagation:  Controlling the import and export of routes
      between ASes and controlling the redistribution of routes between
      BGP and other protocols within an AS.

   Best-path selection:  Selecting the best path when there are multiple
      candidate paths to a given destination network.  This is performed
      by the BGP decision process, which selects the preferred exit
      points out of an AS toward specific destination networks by taking
      a number of different considerations into account.  The BGP path
      selection process can be influenced by manipulating the attributes
      associated with the process, including NEXT_HOP, LOCAL_PREF,
      AS_PATH, ORIGIN, MULTI_EXIT_DISC (MED), IGP metric, etc.

   Most BGP implementations provide constructs that facilitate the
   implementation of complex BGP policies based on pre-configured
   logical conditions.  These can be used to control import and export
   of incoming and outgoing routes, control redistribution of routes
   between BGP and other protocols, and influence the selection of best
   paths by manipulating the attributes (either standardized or local to
   the implementation) associated with the BGP decision process.

   When considering inter-domain TE with BGP, note that the outbound
   traffic exit point is controllable, whereas the interconnection point
   where inbound traffic is received typically is not.  Therefore, it is
   up to each individual network to implement TE strategies that deal
   with the efficient delivery of outbound traffic from its customers to
   its peering points.  The vast majority of TE policy is based on a
   "closest exit" strategy, which offloads inter-domain traffic at the
   nearest outbound peering point towards the destination AS.  Most
   methods of manipulating the point at which inbound traffic enters are
   either ineffective or not accepted in the peering community.

   Inter-domain TE with BGP is generally effective, but it is usually
   applied in a trial-and-error fashion because a TE system usually only
   has a view of the available network resources within one domain (an
   AS in this case).  A systematic approach for inter-domain TE requires
   cooperation between the domains.  Further, what may be considered a
   good solution in one domain may not necessarily be a good solution in
   another.  Moreover, it is generally considered inadvisable for one
   domain to permit a control process from another domain to influence
   the routing and management of traffic in its network.

   MPLS-TE tunnels (LSPs) can add a degree of flexibility in the
   selection of exit points for inter-domain routing by applying the
   concept of relative and absolute metrics.  If BGP attributes are
   defined such that the BGP decision process depends on IGP metrics to
   select exit points for inter-domain traffic, then some inter-domain
   traffic destined to a given peer network can be made to prefer a
   specific exit point by establishing a TE tunnel between the router
   making the selection and the peering point via a TE tunnel and
   assigning the TE tunnel a metric that is smaller than the IGP cost to
   all other peering points.  RSVP-TE protocol extensions for inter-
   domain MPLS and GMPLS are described in [RFC5151].

   Similarly to intra-domain TE, inter-domain TE is best accomplished
   when a traffic matrix can be derived to depict the volume of traffic
   from one AS to another.

   Layer 4 multipath transport protocols are designed to move traffic
   between domains and to allow some influence over the selection of the
   paths.  To be truly effective, these protocols would require
   visibility of paths and network conditions in other domains, but that
   information may not be available, might not be complete, and is not
   necessarily trustworthy.

8.  Overview of Contemporary TE Practices in Operational IP Networks

   This section provides an overview of some TE practices in IP
   networks.  The focus is on aspects of control of the routing function
   in operational contexts.  The intent here is to provide an overview
   of the commonly used practices; the discussion is not intended to be
   exhaustive.

   Service providers apply many of the TE mechanisms described in this
   document to optimize the performance of their IP networks, although
   others choose to not use any of them.  These techniques include
   capacity planning, including adding ECMP options, for long
   timescales; routing control using IGP metrics and MPLS, as well as
   path planning and path control using MPLS and SR for medium
   timescales; and traffic management mechanisms for short timescales.

   *  Capacity planning is an important component of how a service
      provider plans an effective IP network.  These plans may take the
      following aspects into account: location of any new links or
      nodes, WECMP algorithms, existing and predicted traffic patterns,
      costs, link capacity, topology, routing design, and survivability.

   *  Performance optimization of operational networks is usually an
      ongoing process in which traffic statistics, performance
      parameters, and fault indicators are continually collected from
      the network.  This empirical data is analyzed and used to trigger
      TE mechanisms.  Tools that perform what-if analysis can also be
      used to assist the TE process by reviewing scenarios before a new
      set of configurations are implemented in the operational network.

   *  Real-time intra-domain TE using the IGP is done by increasing the
      OSPF or IS-IS metric of a congested link until enough traffic has
      been diverted away from that link.  This approach has some
      limitations as discussed in Section 6.2.  Intra-domain TE
      approaches [RR94] [FT00] [FT01] [WANG] take traffic matrix,
      network topology, and network performance objectives as input and
      produce link metrics and load-sharing ratios.  These processes
      open the possibility for intra-domain TE with IGP to be done in a
      more systematic way.

   Administrators of MPLS-TE networks specify and configure link
   attributes and resource constraints such as maximum reservable
   bandwidth and resource class attributes for the links in the domain.
   A link-state IGP that supports TE extensions (IS-IS-TE or OSPF-TE) is
   used to propagate information about network topology and link
   attributes to all routers in the domain.  Network administrators
   specify the LSPs that are to originate at each router.  For each LSP,
   the network administrator specifies the destination node and the
   attributes of the LSP that indicate the requirements that are to be
   satisfied during the path selection process.  The attributes may
   include an explicit path for the LSP to follow, or the originating
   router may use a local constraint-based routing process to compute
   the path of the LSP.  RSVP-TE is used as a signaling protocol to
   instantiate the LSPs.  By assigning proper bandwidth values to links
   and LSPs, congestion caused by uneven traffic distribution can be
   avoided or mitigated.

   The bandwidth attributes of an LSP relate to the bandwidth
   requirements of traffic that flows through the LSP.  The traffic
   attribute of an LSP can be modified to accommodate persistent shifts
   in demand (traffic growth or reduction).  If network congestion
   occurs due to unexpected events, existing LSPs can be rerouted to
   alleviate the situation, or the network administrator can configure
   new LSPs to divert some traffic to alternative paths.  The reservable
   bandwidth of the congested links can also be reduced to force some
   LSPs to be rerouted to other paths.  A traffic matrix in an MPLS
   domain can also be estimated by monitoring the traffic on LSPs.  Such
   traffic statistics can be used for a variety of purposes including
   network planning and network optimization.

   Network management and planning systems have evolved and assumed a
   lot of the responsibility for determining traffic paths in TE
   networks.  This allows a network-wide view of resources and
   facilitates coordination of the use of resources for all traffic
   flows in the network.  Initial solutions using a PCE to perform path
   computation on behalf of network routers have given way to an
   approach that follows the SDN architecture.  A stateful PCE is able
   to track all of the LSPs in the network and can redistribute them to
   make better use of the available resources.  Such a PCE can form part
   of a network orchestrator that uses PCEP or some other configuration
   and management interface to instruct the signaling protocol or
   directly program the routers.

   SR leverages a centralized TE controller and either an MPLS or IPv6
   forwarding plane but does not need to use a signaling protocol or
   management plane protocol to reserve resources in the routers.  All
   resource reservation is logical within the controller and is not
   distributed to the routers.  Packets are steered through the network
   using SR, and this may have configuration and operational scaling
   benefits.

   As mentioned in Section 7, there is usually no direct control over
   the distribution of inbound traffic to a domain.  Therefore, the main
   goal of inter-domain TE is to optimize the distribution of outbound
   traffic between multiple inter-domain links.  When operating a
   geographically widespread network (such as for a multi-national or
   global network provider), maintaining the ability to operate the
   network in a regional fashion where desired, while continuing to take
   advantage of the benefits of a globally interconnected network, also
   becomes an important objective.

   Inter-domain TE with BGP begins with the placement of multiple
   peering interconnection points that are in close proximity to traffic
   sources/destinations and offer lowest-cost paths across the network
   between the peering points and the sources/destinations.  Some
   location-decision problems that arise in association with inter-
   domain routing are discussed in [AWD5].

   Once the locations of the peering interconnects have been determined
   and implemented, the network operator decides how best to handle the
   routes advertised by the peer, as well as how to propagate the peer's
   routes within their network.  One way to engineer outbound traffic
   flows in a network with many peering interconnects is to create a
   hierarchy of peers.  Generally, the shortest AS paths will be chosen
   to forward traffic, but BGP metrics can be used to prefer some peers
   and so favor particular paths.  Preferred peers are those peers
   attached through peering interconnects with the most available
   capacity.  Changes may be needed, for example, to deal with a
   "problem peer" who is difficult to work with on upgrades or is
   charging high prices for connectivity to their network.  In that
   case, the peer may be given a reduced preference.  This type of
   change can affect a large amount of traffic and is only used after
   other methods have failed to provide the desired results.

   When there are multiple exit points toward a given peer, and only one
   of them is congested, it is not necessary to shift traffic away from
   the peer entirely, but only from the one congested connection.  This
   can be achieved by using passive IGP metrics, AS_PATH filtering, or
   prefix filtering.

9.  Security Considerations

   In general, TE mechanisms are security neutral, and this document
   does not introduce new security issues.

   Network security is, of course, an important issue, and TE mechanisms
   can have benefits and drawbacks:

   *  TE may use tunnels that can slightly help protect traffic from
      inspection and that, in some cases, can be secured using
      encryption.

   *  TE puts traffic onto predictable paths within the network that may
      make it easier to find and attack.

   *  TE often increases the complexity of operation and management of
      the network, which may lead to errors that compromise security.

   *  TE enables traffic to be steered onto more secure links or to more
      secure parts of the network.

   *  TE can be used to steer traffic through network nodes that are
      able to provide additional security functions.

   The consequences of attacks on the control and management protocols
   used to operate TE networks can be significant:

   *  Traffic can be hijacked to pass through specific nodes that
      perform inspection or even to be delivered to the wrong place.

   *  Traffic can be steered onto paths that deliver quality that is
      below the desired quality.

   *  Networks can be congested or have resources on key links consumed.

   Thus, it is important to use adequate protection mechanisms, such as
   authentication, on all protocols used to deliver TE.

   Certain aspects of a network may be deduced from the details of the
   TE paths that are used.  For example, the link connectivity of the
   network and the quality and load on individual links may be inferred
   from knowing the paths of traffic and the requirements they place on
   the network (for example, by seeing the control messages or through
   path-trace techniques).  Such knowledge can be used to launch
   targeted attacks (for example, taking down critical links) or can
   reveal commercially sensitive information (for example, whether a
   network is close to capacity).  Therefore, network operators may
   choose techniques that mask or hide information from within the
   network.

   External control interfaces that are introduced to provide additional
   control and management of TE systems (see Section 5.1.2) provide
   flexibility to management and to customers, but they do so at the
   risk of exposing the internals of a network to potentially malicious
   actors.  The protocols used at these interfaces must be secured to
   protect against snooping and modification, and use of the interfaces
   must be authenticated.

10.  IANA Considerations

   This document has no IANA actions.

11.  Informative References

   [AFD03]    Pan, R., Breslau, L., Prabhakar, B., and S. Shenker,
              "Approximate fairness through differential dropping", ACM
              SIGCOMM Computer Communication Review, Volume 33, Issue 2,
              Pages 23-39, DOI 10.1145/956981.956985, April 2003,
              <https://dl.acm.org/doi/10.1145/956981.956985>.

   [AJ19]     Adekitan, A., Abolade, J., and O. Shobayo, "Data mining
              approach for predicting the daily Internet data traffic of
              a smart university", Journal of Big Data, Volume 6, Number
              1, Page 1, DOI 10.1186/s40537-019-0176-5, February 2019,
              <https://journalofbigdata.springeropen.com/track/
              pdf/10.1186/s40537-019-0176-5.pdf>.

   [ATSSS]    3GPP, "Study on access traffic steering, switch and
              splitting support in the 5G System (5GS) architecture",
              Release 16, 3GPP TR 23.793, December 2018,
              <https://www.3gpp.org/ftp//Specs/
              archive/23_series/23.793/23793-g00.zip>.

   [AWD2]     Awduche, D., "MPLS and traffic engineering in IP
              networks", IEEE Communications Magazine, Volume 37, Issue
              12, Pages 42-47, DOI 10.1109/35.809383, December 1999,
              <https://ieeexplore.ieee.org/document/809383>.

   [AWD5]     Awduche, D., "An approach to optimal peering between
              autonomous systems in the Internet", Proceedings 7th
              International Conference on Computer Communications and
              Networks (Cat. No. 98EX226),
              DOI 10.1109/ICCCN.1998.998795, October 1998,
              <https://ieeexplore.ieee.org/document/998795>.

   [E.360.1]  ITU-T, "Framework for QoS routing and related traffic
              engineering methods for IP-, ATM-, and TDM-based
              multiservice networks", ITU-T Recommendation E.360.1, May
              2002, <https://www.itu.int/rec/T-REC-E.360.1-200205-I/en>.

   [ENHANCED-VPN]
              Dong, J., Bryant, S., Li, Z., Miyasaka, T., and Y. Lee, "A
              Framework for NRP-based Enhanced Virtual Private Network",
              Work in Progress, Internet-Draft, draft-ietf-teas-
              enhanced-vpn-17, 25 December 2023,
              <https://datatracker.ietf.org/doc/html/draft-ietf-teas-
              enhanced-vpn-17>.

   [Err309]   RFC Errata, Erratum ID 309, RFC 3272,
              <https://www.rfc-editor.org/errata/eid309>.

   [EVPN-UNEQUAL-LB]
              Malhotra, N., Ed., Sajassi, A., Rabadan, J., Drake, J.,
              Lingala, A., and S. Thoria, "Weighted Multi-Path
              Procedures for EVPN Multi-Homing", Work in Progress,
              Internet-Draft, draft-ietf-bess-evpn-unequal-lb-21, 7
              December 2023, <https://datatracker.ietf.org/doc/html/
              draft-ietf-bess-evpn-unequal-lb-21>.

   [FLJA93]   Floyd, S. and V. Jacobson, "Random Early Detection
              Gateways for Congestion Avoidance", IEEE/ACM Transactions
              on Networking, Volume 1, Issue 4, Pages 397-413,
              DOI 10.1109/90.251892, August 1993,
              <https://www.icir.org/floyd/papers/early.twocolumn.pdf>.

   [FT00]     Fortz, B. and M. Thorup, "Internet Traffic Engineering by
              Optimizing OSPF Weights", Proceedings IEEE INFOCOM 2000,
              DOI 10.1109/INFCOM.2000.832225, March 2000,
              <https://www.cs.cornell.edu/courses/cs619/2004fa/
              documents/ospf_opt.pdf>.

   [FT01]     Fortz, B. and M. Thorup, "Optimizing OSPF/IS-IS Weights in
              a Changing World", IEEE Journal on Selected Areas in
              Communications, DOI 10.1109/JSAC.2002.1003042, May 2002,
              <https://ieeexplore.ieee.org/document/1003042>.

   [GRPC]     gRPC Authors, "gRPC: A high performance, open source
              universal RPC framework", <https://grpc.io>.

   [KELLY]    Kelly, F., "Notes on effective bandwidths", Oxford
              University Press, 1996.

   [MA]       Ma, Q., "Quality-of-Service Routing in Integrated Services
              Networks", Ph.D. Dissertation, Carnegie Mellon University,
              CMU-CS-98-138, January 1998,
              <https://apps.dtic.mil/sti/pdfs/ADA352299.pdf>.

   [MATE]     Elwalid, A., Jin, C., Low, S., and I. Widjaja, "MATE: MPLS
              Adaptive Traffic Engineering", Proceedings IEEE INFOCOM
              2001, Conference on Computer Communications, Twentieth
              Annual Joint Conference of the IEEE Computer and
              Communications Society (Cat. No. 01CH37213),
              DOI 10.1109/INFCOM.2001.916625, August 2002,
              <https://www.yumpu.com/en/document/view/35140398/mate-
              mpls-adaptive-traffic-engineering-infocom-ieee-xplore/8>.

   [MR99]     Mitra, D. and K.G. Ramakrishnan, "A case study of
              multiservice, multipriority traffic engineering design for
              data networks", Seamless Interconnection for Universal
              Services, Global Telecommunications Conference,
              GLOBECOM'99, (Cat. No. 99CH37042),
              DOI 10.1109/GLOCOM.1999.830281, December 1999,
              <https://ieeexplore.ieee.org/document/830281>.

   [MULTIPATH-DCCP]
              Amend, M., Ed., Brunstrom, A., Kassler, A., Rakocevic, V.,
              and S. Johnson, "DCCP Extensions for Multipath Operation
              with Multiple Addresses", Work in Progress, Internet-
              Draft, draft-ietf-tsvwg-multipath-dccp-11, 12 October
              2023, <https://datatracker.ietf.org/doc/html/draft-ietf-
              tsvwg-multipath-dccp-11>.

   [NETWORK-SLICES]
              Farrel, A., Ed., Drake, J., Ed., Rokui, R., Homma, S.,
              Makhijani, K., Contreras, L. M., and J. Tantsura, "A
              Framework for Network Slices in Networks Built from IETF
              Technologies", Work in Progress, Internet-Draft, draft-
              ietf-teas-ietf-network-slices-25, 14 September 2023,
              <https://datatracker.ietf.org/doc/html/draft-ietf-teas-
              ietf-network-slices-25>.

   [PERFORMANCE-ROUTING]
              Xu, X., Hegde, S., Talaulikar, K., Boucadair, M., and C.
              Jacquenet, "Performance-based BGP Routing Mechanism", Work
              in Progress, Internet-Draft, draft-ietf-idr-performance-
              routing-03, 22 December 2020,
              <https://datatracker.ietf.org/doc/html/draft-ietf-idr-
              performance-routing-03>.

   [QUIC-MULTIPATH]
              Liu, Y., Ed., Ma, Y., Ed., De Coninck, Q., Ed.,
              Bonaventure, O., Huitema, C., and M. Kühlewind, Ed.,
              "Multipath Extension for QUIC", Work in Progress,
              Internet-Draft, draft-ietf-quic-multipath-06, 23 October
              2023, <https://datatracker.ietf.org/doc/html/draft-ietf-
              quic-multipath-06>.

   [RFC0791]  Postel, J., "Internet Protocol", STD 5, RFC 791,
              DOI 10.17487/RFC0791, September 1981,
              <https://www.rfc-editor.org/info/rfc791>.

   [RFC1102]  Clark, D., "Policy routing in Internet protocols",
              RFC 1102, DOI 10.17487/RFC1102, May 1989,
              <https://www.rfc-editor.org/info/rfc1102>.

   [RFC1104]  Braun, H., "Models of policy based routing", RFC 1104,
              DOI 10.17487/RFC1104, June 1989,
              <https://www.rfc-editor.org/info/rfc1104>.

   [RFC2205]  Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and S.
              Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
              Functional Specification", RFC 2205, DOI 10.17487/RFC2205,
              September 1997, <https://www.rfc-editor.org/info/rfc2205>.

   [RFC2330]  Paxson, V., Almes, G., Mahdavi, J., and M. Mathis,
              "Framework for IP Performance Metrics", RFC 2330,
              DOI 10.17487/RFC2330, May 1998,
              <https://www.rfc-editor.org/info/rfc2330>.

   [RFC2386]  Crawley, E., Nair, R., Rajagopalan, B., and H. Sandick, "A
              Framework for QoS-based Routing in the Internet",
              RFC 2386, DOI 10.17487/RFC2386, August 1998,
              <https://www.rfc-editor.org/info/rfc2386>.

   [RFC2474]  Nichols, K., Blake, S., Baker, F., and D. Black,
              "Definition of the Differentiated Services Field (DS
              Field) in the IPv4 and IPv6 Headers", RFC 2474,
              DOI 10.17487/RFC2474, December 1998,
              <https://www.rfc-editor.org/info/rfc2474>.

   [RFC2475]  Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z.,
              and W. Weiss, "An Architecture for Differentiated
              Services", RFC 2475, DOI 10.17487/RFC2475, December 1998,
              <https://www.rfc-editor.org/info/rfc2475>.

   [RFC2597]  Heinanen, J., Baker, F., Weiss, W., and J. Wroclawski,
              "Assured Forwarding PHB Group", RFC 2597,
              DOI 10.17487/RFC2597, June 1999,
              <https://www.rfc-editor.org/info/rfc2597>.

   [RFC2678]  Mahdavi, J. and V. Paxson, "IPPM Metrics for Measuring
              Connectivity", RFC 2678, DOI 10.17487/RFC2678, September
              1999, <https://www.rfc-editor.org/info/rfc2678>.

   [RFC2702]  Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J.
              McManus, "Requirements for Traffic Engineering Over MPLS",
              RFC 2702, DOI 10.17487/RFC2702, September 1999,
              <https://www.rfc-editor.org/info/rfc2702>.

   [RFC2722]  Brownlee, N., Mills, C., and G. Ruth, "Traffic Flow
              Measurement: Architecture", RFC 2722,
              DOI 10.17487/RFC2722, October 1999,
              <https://www.rfc-editor.org/info/rfc2722>.

   [RFC2753]  Yavatkar, R., Pendarakis, D., and R. Guerin, "A Framework
              for Policy-based Admission Control", RFC 2753,
              DOI 10.17487/RFC2753, January 2000,
              <https://www.rfc-editor.org/info/rfc2753>.

   [RFC2961]  Berger, L., Gan, D., Swallow, G., Pan, P., Tommasi, F.,
              and S. Molendini, "RSVP Refresh Overhead Reduction
              Extensions", RFC 2961, DOI 10.17487/RFC2961, April 2001,
              <https://www.rfc-editor.org/info/rfc2961>.

   [RFC2998]  Bernet, Y., Ford, P., Yavatkar, R., Baker, F., Zhang, L.,
              Speer, M., Braden, R., Davie, B., Wroclawski, J., and E.
              Felstaine, "A Framework for Integrated Services Operation
              over Diffserv Networks", RFC 2998, DOI 10.17487/RFC2998,
              November 2000, <https://www.rfc-editor.org/info/rfc2998>.

   [RFC3031]  Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
              Label Switching Architecture", RFC 3031,
              DOI 10.17487/RFC3031, January 2001,
              <https://www.rfc-editor.org/info/rfc3031>.

   [RFC3086]  Nichols, K. and B. Carpenter, "Definition of
              Differentiated Services Per Domain Behaviors and Rules for
              their Specification", RFC 3086, DOI 10.17487/RFC3086,
              April 2001, <https://www.rfc-editor.org/info/rfc3086>.

   [RFC3124]  Balakrishnan, H. and S. Seshan, "The Congestion Manager",
              RFC 3124, DOI 10.17487/RFC3124, June 2001,
              <https://www.rfc-editor.org/info/rfc3124>.

   [RFC3168]  Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
              of Explicit Congestion Notification (ECN) to IP",
              RFC 3168, DOI 10.17487/RFC3168, September 2001,
              <https://www.rfc-editor.org/info/rfc3168>.

   [RFC3175]  Baker, F., Iturralde, C., Le Faucheur, F., and B. Davie,
              "Aggregation of RSVP for IPv4 and IPv6 Reservations",
              RFC 3175, DOI 10.17487/RFC3175, September 2001,
              <https://www.rfc-editor.org/info/rfc3175>.

   [RFC3198]  Westerinen, A., Schnizlein, J., Strassner, J., Scherling,
              M., Quinn, B., Herzog, S., Huynh, A., Carlson, M., Perry,
              J., and S. Waldbusser, "Terminology for Policy-Based
              Management", RFC 3198, DOI 10.17487/RFC3198, November
              2001, <https://www.rfc-editor.org/info/rfc3198>.

   [RFC3209]  Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
              and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
              Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
              <https://www.rfc-editor.org/info/rfc3209>.

   [RFC3270]  Le Faucheur, F., Ed., Wu, L., Davie, B., Davari, S.,
              Vaananen, P., Krishnan, R., Cheval, P., and J. Heinanen,
              "Multi-Protocol Label Switching (MPLS) Support of
              Differentiated Services", RFC 3270, DOI 10.17487/RFC3270,
              May 2002, <https://www.rfc-editor.org/info/rfc3270>.

   [RFC3272]  Awduche, D., Chiu, A., Elwalid, A., Widjaja, I., and X.
              Xiao, "Overview and Principles of Internet Traffic
              Engineering", RFC 3272, DOI 10.17487/RFC3272, May 2002,
              <https://www.rfc-editor.org/info/rfc3272>.

   [RFC3469]  Sharma, V., Ed. and F. Hellstrand, Ed., "Framework for
              Multi-Protocol Label Switching (MPLS)-based Recovery",
              RFC 3469, DOI 10.17487/RFC3469, February 2003,
              <https://www.rfc-editor.org/info/rfc3469>.

   [RFC3473]  Berger, L., Ed., "Generalized Multi-Protocol Label
              Switching (GMPLS) Signaling Resource ReserVation Protocol-
              Traffic Engineering (RSVP-TE) Extensions", RFC 3473,
              DOI 10.17487/RFC3473, January 2003,
              <https://www.rfc-editor.org/info/rfc3473>.

   [RFC3630]  Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering
              (TE) Extensions to OSPF Version 2", RFC 3630,
              DOI 10.17487/RFC3630, September 2003,
              <https://www.rfc-editor.org/info/rfc3630>.

   [RFC3945]  Mannie, E., Ed., "Generalized Multi-Protocol Label
              Switching (GMPLS) Architecture", RFC 3945,
              DOI 10.17487/RFC3945, October 2004,
              <https://www.rfc-editor.org/info/rfc3945>.

   [RFC4090]  Pan, P., Ed., Swallow, G., Ed., and A. Atlas, Ed., "Fast
              Reroute Extensions to RSVP-TE for LSP Tunnels", RFC 4090,
              DOI 10.17487/RFC4090, May 2005,
              <https://www.rfc-editor.org/info/rfc4090>.

   [RFC4124]  Le Faucheur, F., Ed., "Protocol Extensions for Support of
              Diffserv-aware MPLS Traffic Engineering", RFC 4124,
              DOI 10.17487/RFC4124, June 2005,
              <https://www.rfc-editor.org/info/rfc4124>.

   [RFC4203]  Kompella, K., Ed. and Y. Rekhter, Ed., "OSPF Extensions in
              Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 4203, DOI 10.17487/RFC4203, October 2005,
              <https://www.rfc-editor.org/info/rfc4203>.

   [RFC4271]  Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
              Border Gateway Protocol 4 (BGP-4)", RFC 4271,
              DOI 10.17487/RFC4271, January 2006,
              <https://www.rfc-editor.org/info/rfc4271>.

   [RFC4340]  Kohler, E., Handley, M., and S. Floyd, "Datagram
              Congestion Control Protocol (DCCP)", RFC 4340,
              DOI 10.17487/RFC4340, March 2006,
              <https://www.rfc-editor.org/info/rfc4340>.

   [RFC4461]  Yasukawa, S., Ed., "Signaling Requirements for Point-to-
              Multipoint Traffic-Engineered MPLS Label Switched Paths
              (LSPs)", RFC 4461, DOI 10.17487/RFC4461, April 2006,
              <https://www.rfc-editor.org/info/rfc4461>.

   [RFC4594]  Babiarz, J., Chan, K., and F. Baker, "Configuration
              Guidelines for DiffServ Service Classes", RFC 4594,
              DOI 10.17487/RFC4594, August 2006,
              <https://www.rfc-editor.org/info/rfc4594>.

   [RFC4655]  Farrel, A., Vasseur, J.-P., and J. Ash, "A Path
              Computation Element (PCE)-Based Architecture", RFC 4655,
              DOI 10.17487/RFC4655, August 2006,
              <https://www.rfc-editor.org/info/rfc4655>.

   [RFC4872]  Lang, J.P., Ed., Rekhter, Y., Ed., and D. Papadimitriou,
              Ed., "RSVP-TE Extensions in Support of End-to-End
              Generalized Multi-Protocol Label Switching (GMPLS)
              Recovery", RFC 4872, DOI 10.17487/RFC4872, May 2007,
              <https://www.rfc-editor.org/info/rfc4872>.

   [RFC4873]  Berger, L., Bryskin, I., Papadimitriou, D., and A. Farrel,
              "GMPLS Segment Recovery", RFC 4873, DOI 10.17487/RFC4873,
              May 2007, <https://www.rfc-editor.org/info/rfc4873>.

   [RFC4875]  Aggarwal, R., Ed., Papadimitriou, D., Ed., and S.
              Yasukawa, Ed., "Extensions to Resource Reservation
              Protocol - Traffic Engineering (RSVP-TE) for Point-to-
              Multipoint TE Label Switched Paths (LSPs)", RFC 4875,
              DOI 10.17487/RFC4875, May 2007,
              <https://www.rfc-editor.org/info/rfc4875>.

   [RFC5151]  Farrel, A., Ed., Ayyangar, A., and JP. Vasseur, "Inter-
              Domain MPLS and GMPLS Traffic Engineering -- Resource
              Reservation Protocol-Traffic Engineering (RSVP-TE)
              Extensions", RFC 5151, DOI 10.17487/RFC5151, February
              2008, <https://www.rfc-editor.org/info/rfc5151>.

   [RFC5250]  Berger, L., Bryskin, I., Zinin, A., and R. Coltun, "The
              OSPF Opaque LSA Option", RFC 5250, DOI 10.17487/RFC5250,
              July 2008, <https://www.rfc-editor.org/info/rfc5250>.

   [RFC5305]  Li, T. and H. Smit, "IS-IS Extensions for Traffic
              Engineering", RFC 5305, DOI 10.17487/RFC5305, October
              2008, <https://www.rfc-editor.org/info/rfc5305>.

   [RFC5329]  Ishiguro, K., Manral, V., Davey, A., and A. Lindem, Ed.,
              "Traffic Engineering Extensions to OSPF Version 3",
              RFC 5329, DOI 10.17487/RFC5329, September 2008,
              <https://www.rfc-editor.org/info/rfc5329>.

   [RFC5331]  Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
              Label Assignment and Context-Specific Label Space",
              RFC 5331, DOI 10.17487/RFC5331, August 2008,
              <https://www.rfc-editor.org/info/rfc5331>.

   [RFC5357]  Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J.
              Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)",
              RFC 5357, DOI 10.17487/RFC5357, October 2008,
              <https://www.rfc-editor.org/info/rfc5357>.

   [RFC5394]  Bryskin, I., Papadimitriou, D., Berger, L., and J. Ash,
              "Policy-Enabled Path Computation Framework", RFC 5394,
              DOI 10.17487/RFC5394, December 2008,
              <https://www.rfc-editor.org/info/rfc5394>.

   [RFC5440]  Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation
              Element (PCE) Communication Protocol (PCEP)", RFC 5440,
              DOI 10.17487/RFC5440, March 2009,
              <https://www.rfc-editor.org/info/rfc5440>.

   [RFC5470]  Sadasivan, G., Brownlee, N., Claise, B., and J. Quittek,
              "Architecture for IP Flow Information Export", RFC 5470,
              DOI 10.17487/RFC5470, March 2009,
              <https://www.rfc-editor.org/info/rfc5470>.

   [RFC5472]  Zseby, T., Boschi, E., Brownlee, N., and B. Claise, "IP
              Flow Information Export (IPFIX) Applicability", RFC 5472,
              DOI 10.17487/RFC5472, March 2009,
              <https://www.rfc-editor.org/info/rfc5472>.

   [RFC5541]  Le Roux, JL., Vasseur, JP., and Y. Lee, "Encoding of
              Objective Functions in the Path Computation Element
              Communication Protocol (PCEP)", RFC 5541,
              DOI 10.17487/RFC5541, June 2009,
              <https://www.rfc-editor.org/info/rfc5541>.

   [RFC5557]  Lee, Y., Le Roux, JL., King, D., and E. Oki, "Path
              Computation Element Communication Protocol (PCEP)
              Requirements and Protocol Extensions in Support of Global
              Concurrent Optimization", RFC 5557, DOI 10.17487/RFC5557,
              July 2009, <https://www.rfc-editor.org/info/rfc5557>.

   [RFC5559]  Eardley, P., Ed., "Pre-Congestion Notification (PCN)
              Architecture", RFC 5559, DOI 10.17487/RFC5559, June 2009,
              <https://www.rfc-editor.org/info/rfc5559>.

   [RFC5623]  Oki, E., Takeda, T., Le Roux, JL., and A. Farrel,
              "Framework for PCE-Based Inter-Layer MPLS and GMPLS
              Traffic Engineering", RFC 5623, DOI 10.17487/RFC5623,
              September 2009, <https://www.rfc-editor.org/info/rfc5623>.

   [RFC5664]  Halevy, B., Welch, B., and J. Zelenka, "Object-Based
              Parallel NFS (pNFS) Operations", RFC 5664,
              DOI 10.17487/RFC5664, January 2010,
              <https://www.rfc-editor.org/info/rfc5664>.

   [RFC5671]  Yasukawa, S. and A. Farrel, Ed., "Applicability of the
              Path Computation Element (PCE) to Point-to-Multipoint
              (P2MP) MPLS and GMPLS Traffic Engineering (TE)", RFC 5671,
              DOI 10.17487/RFC5671, October 2009,
              <https://www.rfc-editor.org/info/rfc5671>.

   [RFC5693]  Seedorf, J. and E. Burger, "Application-Layer Traffic
              Optimization (ALTO) Problem Statement", RFC 5693,
              DOI 10.17487/RFC5693, October 2009,
              <https://www.rfc-editor.org/info/rfc5693>.

   [RFC6107]  Shiomoto, K., Ed. and A. Farrel, Ed., "Procedures for
              Dynamically Signaled Hierarchical Label Switched Paths",
              RFC 6107, DOI 10.17487/RFC6107, February 2011,
              <https://www.rfc-editor.org/info/rfc6107>.

   [RFC6119]  Harrison, J., Berger, J., and M. Bartlett, "IPv6 Traffic
              Engineering in IS-IS", RFC 6119, DOI 10.17487/RFC6119,
              February 2011, <https://www.rfc-editor.org/info/rfc6119>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/info/rfc6241>.

   [RFC6372]  Sprecher, N., Ed. and A. Farrel, Ed., "MPLS Transport
              Profile (MPLS-TP) Survivability Framework", RFC 6372,
              DOI 10.17487/RFC6372, September 2011,
              <https://www.rfc-editor.org/info/rfc6372>.

   [RFC6374]  Frost, D. and S. Bryant, "Packet Loss and Delay
              Measurement for MPLS Networks", RFC 6374,
              DOI 10.17487/RFC6374, September 2011,
              <https://www.rfc-editor.org/info/rfc6374>.

   [RFC6601]  Ash, G., Ed. and D. McDysan, "Generic Connection Admission
              Control (GCAC) Algorithm Specification for IP/MPLS
              Networks", RFC 6601, DOI 10.17487/RFC6601, April 2012,
              <https://www.rfc-editor.org/info/rfc6601>.

   [RFC6805]  King, D., Ed. and A. Farrel, Ed., "The Application of the
              Path Computation Element Architecture to the Determination
              of a Sequence of Domains in MPLS and GMPLS", RFC 6805,
              DOI 10.17487/RFC6805, November 2012,
              <https://www.rfc-editor.org/info/rfc6805>.

   [RFC7011]  Claise, B., Ed., Trammell, B., Ed., and P. Aitken,
              "Specification of the IP Flow Information Export (IPFIX)
              Protocol for the Exchange of Flow Information", STD 77,
              RFC 7011, DOI 10.17487/RFC7011, September 2013,
              <https://www.rfc-editor.org/info/rfc7011>.

   [RFC7149]  Boucadair, M. and C. Jacquenet, "Software-Defined
              Networking: A Perspective from within a Service Provider
              Environment", RFC 7149, DOI 10.17487/RFC7149, March 2014,
              <https://www.rfc-editor.org/info/rfc7149>.

   [RFC7285]  Alimi, R., Ed., Penno, R., Ed., Yang, Y., Ed., Kiesel, S.,
              Previdi, S., Roome, W., Shalunov, S., and R. Woundy,
              "Application-Layer Traffic Optimization (ALTO) Protocol",
              RFC 7285, DOI 10.17487/RFC7285, September 2014,
              <https://www.rfc-editor.org/info/rfc7285>.

   [RFC7390]  Rahman, A., Ed. and E. Dijk, Ed., "Group Communication for
              the Constrained Application Protocol (CoAP)", RFC 7390,
              DOI 10.17487/RFC7390, October 2014,
              <https://www.rfc-editor.org/info/rfc7390>.

   [RFC7426]  Haleplidis, E., Ed., Pentikousis, K., Ed., Denazis, S.,
              Hadi Salim, J., Meyer, D., and O. Koufopavlou, "Software-
              Defined Networking (SDN): Layers and Architecture
              Terminology", RFC 7426, DOI 10.17487/RFC7426, January
              2015, <https://www.rfc-editor.org/info/rfc7426>.

   [RFC7471]  Giacalone, S., Ward, D., Drake, J., Atlas, A., and S.
              Previdi, "OSPF Traffic Engineering (TE) Metric
              Extensions", RFC 7471, DOI 10.17487/RFC7471, March 2015,
              <https://www.rfc-editor.org/info/rfc7471>.

   [RFC7491]  King, D. and A. Farrel, "A PCE-Based Architecture for
              Application-Based Network Operations", RFC 7491,
              DOI 10.17487/RFC7491, March 2015,
              <https://www.rfc-editor.org/info/rfc7491>.

   [RFC7551]  Zhang, F., Ed., Jing, R., and R. Gandhi, Ed., "RSVP-TE
              Extensions for Associated Bidirectional Label Switched
              Paths (LSPs)", RFC 7551, DOI 10.17487/RFC7551, May 2015,
              <https://www.rfc-editor.org/info/rfc7551>.

   [RFC7567]  Baker, F., Ed. and G. Fairhurst, Ed., "IETF
              Recommendations Regarding Active Queue Management",
              BCP 197, RFC 7567, DOI 10.17487/RFC7567, July 2015,
              <https://www.rfc-editor.org/info/rfc7567>.

   [RFC7665]  Halpern, J., Ed. and C. Pignataro, Ed., "Service Function
              Chaining (SFC) Architecture", RFC 7665,
              DOI 10.17487/RFC7665, October 2015,
              <https://www.rfc-editor.org/info/rfc7665>.

   [RFC7679]  Almes, G., Kalidindi, S., Zekauskas, M., and A. Morton,
              Ed., "A One-Way Delay Metric for IP Performance Metrics
              (IPPM)", STD 81, RFC 7679, DOI 10.17487/RFC7679, January
              2016, <https://www.rfc-editor.org/info/rfc7679>.

   [RFC7680]  Almes, G., Kalidindi, S., Zekauskas, M., and A. Morton,
              Ed., "A One-Way Loss Metric for IP Performance Metrics
              (IPPM)", STD 82, RFC 7680, DOI 10.17487/RFC7680, January
              2016, <https://www.rfc-editor.org/info/rfc7680>.

   [RFC7923]  Voit, E., Clemm, A., and A. Gonzalez Prieto, "Requirements
              for Subscription to YANG Datastores", RFC 7923,
              DOI 10.17487/RFC7923, June 2016,
              <https://www.rfc-editor.org/info/rfc7923>.

   [RFC7926]  Farrel, A., Ed., Drake, J., Bitar, N., Swallow, G.,
              Ceccarelli, D., and X. Zhang, "Problem Statement and
              Architecture for Information Exchange between
              Interconnected Traffic-Engineered Networks", BCP 206,
              RFC 7926, DOI 10.17487/RFC7926, July 2016,
              <https://www.rfc-editor.org/info/rfc7926>.

   [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
              RFC 7950, DOI 10.17487/RFC7950, August 2016,
              <https://www.rfc-editor.org/info/rfc7950>.

   [RFC8033]  Pan, R., Natarajan, P., Baker, F., and G. White,
              "Proportional Integral Controller Enhanced (PIE): A
              Lightweight Control Scheme to Address the Bufferbloat
              Problem", RFC 8033, DOI 10.17487/RFC8033, February 2017,
              <https://www.rfc-editor.org/info/rfc8033>.

   [RFC8034]  White, G. and R. Pan, "Active Queue Management (AQM) Based
              on Proportional Integral Controller Enhanced (PIE) for
              Data-Over-Cable Service Interface Specifications (DOCSIS)
              Cable Modems", RFC 8034, DOI 10.17487/RFC8034, February
              2017, <https://www.rfc-editor.org/info/rfc8034>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

   [RFC8051]  Zhang, X., Ed. and I. Minei, Ed., "Applicability of a
              Stateful Path Computation Element (PCE)", RFC 8051,
              DOI 10.17487/RFC8051, January 2017,
              <https://www.rfc-editor.org/info/rfc8051>.

   [RFC8189]  Randriamasy, S., Roome, W., and N. Schwan, "Multi-Cost
              Application-Layer Traffic Optimization (ALTO)", RFC 8189,
              DOI 10.17487/RFC8189, October 2017,
              <https://www.rfc-editor.org/info/rfc8189>.

   [RFC8231]  Crabbe, E., Minei, I., Medved, J., and R. Varga, "Path
              Computation Element Communication Protocol (PCEP)
              Extensions for Stateful PCE", RFC 8231,
              DOI 10.17487/RFC8231, September 2017,
              <https://www.rfc-editor.org/info/rfc8231>.

   [RFC8259]  Bray, T., Ed., "The JavaScript Object Notation (JSON) Data
              Interchange Format", STD 90, RFC 8259,
              DOI 10.17487/RFC8259, December 2017,
              <https://www.rfc-editor.org/info/rfc8259>.

   [RFC8279]  Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
              Przygienda, T., and S. Aldrin, "Multicast Using Bit Index
              Explicit Replication (BIER)", RFC 8279,
              DOI 10.17487/RFC8279, November 2017,
              <https://www.rfc-editor.org/info/rfc8279>.

   [RFC8281]  Crabbe, E., Minei, I., Sivabalan, S., and R. Varga, "Path
              Computation Element Communication Protocol (PCEP)
              Extensions for PCE-Initiated LSP Setup in a Stateful PCE
              Model", RFC 8281, DOI 10.17487/RFC8281, December 2017,
              <https://www.rfc-editor.org/info/rfc8281>.

   [RFC8283]  Farrel, A., Ed., Zhao, Q., Ed., Li, Z., and C. Zhou, "An
              Architecture for Use of PCE and the PCE Communication
              Protocol (PCEP) in a Network with Central Control",
              RFC 8283, DOI 10.17487/RFC8283, December 2017,
              <https://www.rfc-editor.org/info/rfc8283>.

   [RFC8290]  Hoeiland-Joergensen, T., McKenney, P., Taht, D., Gettys,
              J., and E. Dumazet, "The Flow Queue CoDel Packet Scheduler
              and Active Queue Management Algorithm", RFC 8290,
              DOI 10.17487/RFC8290, January 2018,
              <https://www.rfc-editor.org/info/rfc8290>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

   [RFC8453]  Ceccarelli, D., Ed. and Y. Lee, Ed., "Framework for
              Abstraction and Control of TE Networks (ACTN)", RFC 8453,
              DOI 10.17487/RFC8453, August 2018,
              <https://www.rfc-editor.org/info/rfc8453>.

   [RFC8570]  Ginsberg, L., Ed., Previdi, S., Ed., Giacalone, S., Ward,
              D., Drake, J., and Q. Wu, "IS-IS Traffic Engineering (TE)
              Metric Extensions", RFC 8570, DOI 10.17487/RFC8570, March
              2019, <https://www.rfc-editor.org/info/rfc8570>.

   [RFC8571]  Ginsberg, L., Ed., Previdi, S., Wu, Q., Tantsura, J., and
              C. Filsfils, "BGP - Link State (BGP-LS) Advertisement of
              IGP Traffic Engineering Performance Metric Extensions",
              RFC 8571, DOI 10.17487/RFC8571, March 2019,
              <https://www.rfc-editor.org/info/rfc8571>.

   [RFC8655]  Finn, N., Thubert, P., Varga, B., and J. Farkas,
              "Deterministic Networking Architecture", RFC 8655,
              DOI 10.17487/RFC8655, October 2019,
              <https://www.rfc-editor.org/info/rfc8655>.

   [RFC8664]  Sivabalan, S., Filsfils, C., Tantsura, J., Henderickx, W.,
              and J. Hardwick, "Path Computation Element Communication
              Protocol (PCEP) Extensions for Segment Routing", RFC 8664,
              DOI 10.17487/RFC8664, December 2019,
              <https://www.rfc-editor.org/info/rfc8664>.

   [RFC8684]  Ford, A., Raiciu, C., Handley, M., Bonaventure, O., and C.
              Paasch, "TCP Extensions for Multipath Operation with
              Multiple Addresses", RFC 8684, DOI 10.17487/RFC8684, March
              2020, <https://www.rfc-editor.org/info/rfc8684>.

   [RFC8685]  Zhang, F., Zhao, Q., Gonzalez de Dios, O., Casellas, R.,
              and D. King, "Path Computation Element Communication
              Protocol (PCEP) Extensions for the Hierarchical Path
              Computation Element (H-PCE) Architecture", RFC 8685,
              DOI 10.17487/RFC8685, December 2019,
              <https://www.rfc-editor.org/info/rfc8685>.

   [RFC8795]  Liu, X., Bryskin, I., Beeram, V., Saad, T., Shah, H., and
              O. Gonzalez de Dios, "YANG Data Model for Traffic
              Engineering (TE) Topologies", RFC 8795,
              DOI 10.17487/RFC8795, August 2020,
              <https://www.rfc-editor.org/info/rfc8795>.

   [RFC8803]  Bonaventure, O., Ed., Boucadair, M., Ed., Gundavelli, S.,
              Seo, S., and B. Hesmans, "0-RTT TCP Convert Protocol",
              RFC 8803, DOI 10.17487/RFC8803, July 2020,
              <https://www.rfc-editor.org/info/rfc8803>.

   [RFC8896]  Randriamasy, S., Yang, R., Wu, Q., Deng, L., and N.
              Schwan, "Application-Layer Traffic Optimization (ALTO)
              Cost Calendar", RFC 8896, DOI 10.17487/RFC8896, November
              2020, <https://www.rfc-editor.org/info/rfc8896>.

   [RFC8938]  Varga, B., Ed., Farkas, J., Berger, L., Malis, A., and S.
              Bryant, "Deterministic Networking (DetNet) Data Plane
              Framework", RFC 8938, DOI 10.17487/RFC8938, November 2020,
              <https://www.rfc-editor.org/info/rfc8938>.

   [RFC8955]  Loibl, C., Hares, S., Raszuk, R., McPherson, D., and M.
              Bacher, "Dissemination of Flow Specification Rules",
              RFC 8955, DOI 10.17487/RFC8955, December 2020,
              <https://www.rfc-editor.org/info/rfc8955>.

   [RFC8972]  Mirsky, G., Min, X., Nydell, H., Foote, R., Masputra, A.,
              and E. Ruffini, "Simple Two-Way Active Measurement
              Protocol Optional Extensions", RFC 8972,
              DOI 10.17487/RFC8972, January 2021,
              <https://www.rfc-editor.org/info/rfc8972>.

   [RFC9000]  Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
              Multiplexed and Secure Transport", RFC 9000,
              DOI 10.17487/RFC9000, May 2021,
              <https://www.rfc-editor.org/info/rfc9000>.

   [RFC9023]  Varga, B., Ed., Farkas, J., Malis, A., and S. Bryant,
              "Deterministic Networking (DetNet) Data Plane: IP over
              IEEE 802.1 Time-Sensitive Networking (TSN)", RFC 9023,
              DOI 10.17487/RFC9023, June 2021,
              <https://www.rfc-editor.org/info/rfc9023>.

   [RFC9040]  Touch, J., Welzl, M., and S. Islam, "TCP Control Block
              Interdependence", RFC 9040, DOI 10.17487/RFC9040, July
              2021, <https://www.rfc-editor.org/info/rfc9040>.

   [RFC9113]  Thomson, M., Ed. and C. Benfield, Ed., "HTTP/2", RFC 9113,
              DOI 10.17487/RFC9113, June 2022,
              <https://www.rfc-editor.org/info/rfc9113>.

   [RFC9256]  Filsfils, C., Talaulikar, K., Ed., Voyer, D., Bogdanov,
              A., and P. Mattes, "Segment Routing Policy Architecture",
              RFC 9256, DOI 10.17487/RFC9256, July 2022,
              <https://www.rfc-editor.org/info/rfc9256>.

   [RFC9262]  Eckert, T., Ed., Menth, M., and G. Cauchie, "Tree
              Engineering for Bit Index Explicit Replication (BIER-TE)",
              RFC 9262, DOI 10.17487/RFC9262, October 2022,
              <https://www.rfc-editor.org/info/rfc9262>.

   [RFC9298]  Schinazi, D., "Proxying UDP in HTTP", RFC 9298,
              DOI 10.17487/RFC9298, August 2022,
              <https://www.rfc-editor.org/info/rfc9298>.

   [RFC9315]  Clemm, A., Ciavaglia, L., Granville, L. Z., and J.
              Tantsura, "Intent-Based Networking - Concepts and
              Definitions", RFC 9315, DOI 10.17487/RFC9315, October
              2022, <https://www.rfc-editor.org/info/rfc9315>.

   [RFC9332]  De Schepper, K., Briscoe, B., Ed., and G. White, "Dual-
              Queue Coupled Active Queue Management (AQM) for Low
              Latency, Low Loss, and Scalable Throughput (L4S)",
              RFC 9332, DOI 10.17487/RFC9332, January 2023,
              <https://www.rfc-editor.org/info/rfc9332>.

   [RFC9350]  Psenak, P., Ed., Hegde, S., Filsfils, C., Talaulikar, K.,
              and A. Gulko, "IGP Flexible Algorithm", RFC 9350,
              DOI 10.17487/RFC9350, February 2023,
              <https://www.rfc-editor.org/info/rfc9350>.

   [RFC9439]  Wu, Q., Yang, Y., Lee, Y., Dhody, D., Randriamasy, S., and
              L. Contreras, "Application-Layer Traffic Optimization
              (ALTO) Performance Cost Metrics", RFC 9439,
              DOI 10.17487/RFC9439, August 2023,
              <https://www.rfc-editor.org/info/rfc9439>.

   [RFC9502]  Britto, W., Hegde, S., Kaneriya, P., Shetty, R., Bonica,
              R., and P. Psenak, "IGP Flexible Algorithm in IP
              Networks", RFC 9502, DOI 10.17487/RFC9502, November 2023,
              <https://www.rfc-editor.org/info/rfc9502>.

   [RFC9552]  Talaulikar, K., Ed., "Distribution of Link-State and
              Traffic Engineering Information Using BGP", RFC 9552,
              DOI 10.17487/RFC9552, December 2023,
              <https://www.rfc-editor.org/info/rfc9552>.

   [RR94]     Rodrigues, M. and K.G. Ramakrishnan, "Optimal routing in
              shortest-path data networks", Bell Labs Technical Journal,
              Volume 6, Issue 1, Pages 117-138, DOI 10.1002/bltj.2267,
              August 2002,
              <https://onlinelibrary.wiley.com/doi/abs/10.1002/
              bltj.2267>.

   [SLDC98]   Suter, B., Lakshman, T.V., Stiliadis, D., and A.K.
              Choudhury, "Design considerations for supporting TCP with
              per-flow queueing", Proceedings IEEE INFOCOM '98,
              DOI 10.1109/INFCOM.1998.659666, April 1998,
              <https://ieeexplore.ieee.org/document/659666>.

   [SR-TE-POLICY]
              Previdi, S., Filsfils, C., Talaulikar, K., Ed., Mattes,
              P., and D. Jain, "Advertising Segment Routing Policies in
              BGP", Work in Progress, Internet-Draft, draft-ietf-idr-
              segment-routing-te-policy-26, 23 October 2023,
              <https://datatracker.ietf.org/doc/html/draft-ietf-idr-
              segment-routing-te-policy-26>.

   [SR-TI-LFA]
              Bashandy, A., Litkowski, S., Filsfils, C., Francois, P.,
              Decraene, B., and D. Voyer, "Topology Independent Fast
              Reroute using Segment Routing", Work in Progress,
              Internet-Draft, draft-ietf-rtgwg-segment-routing-ti-lfa-
              13, 16 January 2024,
              <https://datatracker.ietf.org/doc/html/draft-ietf-rtgwg-
              segment-routing-ti-lfa-13>.

   [TE-QoS-ROUTING]
              Ash, G., "Traffic Engineering & QoS Methods for IP-, ATM-,
              & Based Multiservice Networks", Work in Progress,
              Internet-Draft, draft-ietf-tewg-qos-routing-04, October
              2001, <https://datatracker.ietf.org/doc/html/draft-ietf-
              tewg-qos-routing-04>.

   [WANG]     Wang, Y., Wang, Z., and L. Zhang, "Internet traffic
              engineering without full mesh overlaying", Proceedings
              IEEE INFOCOM 2001, DOI 10.1109/INFCOM.2001.916782, April
              2001, <https://ieeexplore.ieee.org/document/916782>.

   [XIAO]     Xiao, X., Hannan, A., Bailey, B., and L. Ni, "Traffic
              Engineering with MPLS in the Internet", IEEE Network,
              Volume 14, Issue 2, Pages 28-33, DOI 10.1109/65.826369,
              March 2000,
              <https://courses.cs.washington.edu/courses/cse561/02au/
              papers/xiao-mpls-net00.pdf>.

   [YARE95]   Yang, C. and A. Reddy, "A Taxonomy for Congestion Control
              Algorithms in Packet Switching Networks", IEEE Network,
              Pages 34-45, DOI 10.1109/65.397042, August 1995,
              <https://ieeexplore.ieee.org/document/397042>.

Appendix A.  Summary of Changes since RFC 3272

   The changes to this document since [RFC3272] are substantial and not
   easily summarized as section-by-section changes.  The material in the
   document has been moved around considerably, some of it removed, and
   new text added.

   The approach taken here is to list the contents of both [RFC3272] and
   this document saying, respectively, where the text has been placed
   and where the text came from.

A.1.  RFC 3272

   *  Section 1.0 ("Introduction"): Edited in place in Section 1.

      -  Section 1.1 ("What is Internet Traffic Engineering?"): Edited
         in place in Section 1.1.

      -  Section 1.2 ("Scope"): Moved to Section 1.3.

      -  Section 1.3 ("Terminology"): Moved to Section 1.4 with some
         obsolete terms removed and a little editing.

   *  Section 2.0 ("Background"): Retained as Section 2 with some text
      removed.

      -  Section 2.1 ("Context of Internet Traffic Engineering"):
         Retained as Section 2.1.

      -  Section 2.2 ("Network Context"): Rewritten as Section 2.2.

      -  Section 2.3 ("Problem Context"): Rewritten as Section 2.3.

         o  Section 2.3.1 ("Congestion and its Ramifications"): Retained
            as Section 2.3.1.

      -  Section 2.4 ("Solution Context"): Edited as Section 2.4.

         o  Section 2.4.1 ("Combating the Congestion Problem"):
            Reformatted as Section 2.4.1.

      -  Section 2.5 ("Implementation and Operational Context"):
         Retained as Section 2.5.

   *  Section 3.0 ("Traffic Engineering Process Model"): Retained as
      Section 3.

      -  Section 3.1 ("Components of the Traffic Engineering Process
         Model"): Retained as Section 3.1.

      -  Section 3.2 ("Measurement"): Merged into Section 3.1.

      -  Section 3.3 ("Modeling, Analysis, and Simulation"): Merged into
         Section 3.1.

      -  Section 3.4 ("Optimization"): Merged into Section 3.1.

   *  Section 4.0 ("Historical Review and Recent Developments"):
      Retained as Section 5, but the very historic aspects have been
      deleted.

      -  Section 4.1 ("Traffic Engineering in Classical Telephone
         Networks"): Deleted.

      -  Section 4.2 ("Evolution of Traffic Engineering in the
         Internet"): Deleted.

      -  Section 4.3 ("Overlay Model"): Deleted.

      -  Section 4.4 ("Constraint-Based Routing"): Retained as
         Section 5.1.3.1, but moved into Section 5.1.

      -  Section 4.5 ("Overview of Other IETF Projects Related to
         Traffic Engineering"): Retained as Section 5.1 with many new
         subsections.

         o  Section 4.5.1 ("Integrated Services"): Retained as
            Section 5.1.1.1.

         o  Section 4.5.2 ("RSVP"): Retained as Section 5.1.3.2 with
            some edits.

         o  Section 4.5.3 ("Differentiated Services"): Retained as
            Section 5.1.1.2.

         o  Section 4.5.4 ("MPLS"): Retained as Section 5.1.3.3.

         o  Section 4.5.5 ("IP Performance Metrics"): Retained as
            Section 5.1.3.6.

         o  Section 4.5.6 ("Flow Measurement"): Retained as
            Section 5.1.3.7 with some reformatting.

         o  Section 4.5.7 ("Endpoint Congestion Management"): Retained
            as Section 5.1.3.8.

      -  Section 4.6 ("Overview of ITU Activities Related to Traffic
         Engineering"): Deleted.

      -  Section 4.7 ("Content Distribution"): Retained as Section 5.2.

   *  Section 5.0 ("Taxonomy of Traffic Engineering Systems"): Retained
      as Section 4.

      -  Section 5.1 ("Time-Dependent Versus State-Dependent"): Retained
         as Section 4.1.

      -  Section 5.2 ("Offline Versus Online"): Retained as Section 4.2.

      -  Section 5.3 ("Centralized Versus Distributed"): Retained as
         Section 4.3 with additions.

      -  Section 5.4 ("Local Versus Global"): Retained as Section 4.4.

      -  Section 5.5 ("Prescriptive Versus Descriptive"): Retained as
         Section 4.5 with additions.

      -  Section 5.6 ("Open-Loop Versus Closed-Loop"): Retained as
         Section 4.6.

      -  Section 5.7 ("Tactical vs Strategic"): Retained as Section 4.7.

   *  Section 6.0 ("Recommendations for Internet Traffic Engineering"):
      Retained as Section 6.

      -  Section 6.1 ("Generic Non-functional Recommendations"):
         Retained as Section 6.1.

      -  Section 6.2 ("Routing Recommendations"): Retained as
         Section 6.2 with edits.

      -  Section 6.3 ("Traffic Mapping Recommendations"): Retained as
         Section 6.3.

      -  Section 6.4 ("Measurement Recommendations"): Retained as
         Section 6.4.

      -  Section 6.5 ("Network Survivability"): Retained as Section 6.6.

         o  Section 6.5.1 ("Survivability in MPLS Based Networks"):
            Retained as Section 6.6.1.

         o  Section 6.5.2 ("Protection Option"): Retained as
            Section 6.6.2.

      -  Section 6.6 ("Traffic Engineering in Diffserv Environments"):
         Retained as Section 6.8 with edits.

      -  Section 6.7 ("Network Controllability"): Retained as
         Section 6.9.

   *  Section 7.0 ("Inter-Domain Considerations"): Retained as
      Section 7.

   *  Section 8.0 ("Overview of Contemporary TE Practices in Operational
      IP Networks"): Retained as Section 8.

   *  Section 9.0 ("Conclusion"): Removed.

   *  Section 10.0 ("Security Considerations"): Retained as Section 9
      with considerable new text.

A.2.  This Document

   *  Section 1: Based on Section 1 of [RFC3272].

      -  Section 1.1: Based on Section 1.1 of [RFC3272].

      -  Section 1.2: New for this document.

      -  Section 1.3: Based on Section 1.2 of [RFC3272].

      -  Section 1.4: Based on Section 1.3 of [RFC3272].

   *  Section 2: Based on Section 2 of [RFC3272].

      -  Section 2.1: Based on Section 2.1 of [RFC3272].

      -  Section 2.2: Based on Section 2.2 of [RFC3272].

      -  Section 2.3: Based on Section 2.3 of [RFC3272].

         o  Section 2.3.1: Based on Section 2.3.1 of [RFC3272].

      -  Section 2.4: Based on Section 2.4 of [RFC3272].

         o  Section 2.4.1: Based on Section 2.4.1 of [RFC3272].

      -  Section 2.5: Based on Section 2.5 of [RFC3272].

   *  Section 3: Based on Section 3 of [RFC3272].

      -  Section 3.1: Based on Sections 3.1, 3.2, 3.3, and 3.4 of
         [RFC3272].

   *  Section 4: Based on Section 5 of [RFC3272].

      -  Section 4.1: Based on Section 5.1 of [RFC3272].

      -  Section 4.2: Based on Section 5.2 of [RFC3272].

      -  Section 4.3: Based on Section 5.3 of [RFC3272].

         o  Section 4.3.1: New for this document.

         o  Section 4.3.2: New for this document.

      -  Section 4.4: Based on Section 5.4 of [RFC3272].

      -  Section 4.5: Based on Section 5.5 of [RFC3272].

         o  Section 4.5.1: New for this document.

      -  Section 4.6: Based on Section 5.6 of [RFC3272].

      -  Section 4.7: Based on Section 5.7 of [RFC3272].

   *  Section 5: Based on Section 4 of [RFC3272].

      -  Section 5.1: Based on Section 4.5 of [RFC3272].

         o  Section 5.1.1.1: Based on Section 4.5.1 of [RFC3272].

         o  Section 5.1.1.2: Based on Section 4.5.3 of [RFC3272].

         o  Section 5.1.1.3: New for this document.

         o  Section 5.1.1.4: New for this document.

         o  Section 5.1.1.5: New for this document.

         o  Section 5.1.2.1: New for this document.

         o  Section 5.1.2.2: New for this document.

         o  Section 5.1.2.3: New for this document.

         o  Section 5.1.3.1: Based on Section 4.4 of [RFC3272].

            +  Section 5.1.3.1.1: New for this document.

         o  Section 5.1.3.2: Based on Section 4.5.2 of [RFC3272].

         o  Section 5.1.3.3: Based on Section 4.5.4 of [RFC3272].

         o  Section 5.1.3.4: New for this document.

         o  Section 5.1.3.5: New for this document.

         o  Section 5.1.3.6: Based on Section 4.5.5 of [RFC3272].

         o  Section 5.1.3.7: Based on Section 4.5.6 of [RFC3272].

         o  Section 5.1.3.8: Based on Section 4.5.7 of [RFC3272].

         o  Section 5.1.3.9: New for this document.

         o  Section 5.1.3.10: New for this document.

         o  Section 5.1.3.11: New for this document.

         o  Section 5.1.3.12: New for this document.

         o  Section 5.1.3.13: New for this document.

         o  Section 5.1.3.14: New for this document.

         o  Section 5.1.3.15: New for this document.

      -  Section 5.2: Based on Section 4.7 of [RFC3272].

   *  Section 6: Based on Section 6 of [RFC3272].

      -  Section 6.1: Based on Section 6.1 of [RFC3272].

      -  Section 6.2: Based on Section 6.2 of [RFC3272].

      -  Section 6.3: Based on Section 6.3 of [RFC3272].

      -  Section 6.4: Based on Section 6.4 of [RFC3272].

      -  Section 6.5: New for this document.

      -  Section 6.6: Based on Section 6.5 of [RFC3272].

         o  Section 6.6.1: Based on Section 6.5.1 of [RFC3272].

         o  Section 6.6.2: Based on Section 6.5.2 of [RFC3272].

      -  Section 6.7: New for this document.

      -  Section 6.8: Based on Section 6.6 of [RFC3272].

      -  Section 6.9: Based on Section 6.7 of [RFC3272].

   *  Section 7: Based on Section 7 of [RFC3272].

   *  Section 8: Based on Section 8 of [RFC3272].

   *  Section 9: Based on Section 10 of [RFC3272].

Acknowledgments

   Much of the text in this document is derived from [RFC3272].  The
   editor and contributors to this document would like to express their
   gratitude to all involved in that work.  Although the source text has
   been edited in the production of this document, the original authors
   should be considered as contributors to this work.  They were:

   Daniel O. Awduche
   Movaz Networks


   Angela Chiu
   Celion Networks


   Anwar Elwalid
   Lucent Technologies


   Indra Widjaja
   Bell Labs, Lucent Technologies


   XiPeng Xiao
   Redback Networks


   The acknowledgements in [RFC3272] were as below.  All people who
   helped in the production of that document also need to be thanked for
   the carry-over into this new document.

   |  The authors would like to thank Jim Boyle for inputs on the
   |  recommendations section, Francois Le Faucheur for inputs on
   |  Diffserv aspects, Blaine Christian for inputs on measurement,
   |  Gerald Ash for inputs on routing in telephone networks and for
   |  text on event-dependent TE methods, Steven Wright for inputs on
   |  network controllability, and Jonathan Aufderheide for inputs on
   |  inter-domain TE with BGP.  Special thanks to Randy Bush for
   |  proposing the TE taxonomy based on "tactical vs strategic"
   |  methods.  The subsection describing an "Overview of ITU Activities
   |  Related to Traffic Engineering" was adapted from a contribution by
   |  Waisum Lai.  Useful feedback and pointers to relevant materials
   |  were provided by J. Noel Chiappa.  Additional comments were
   |  provided by Glenn Grotefeld during the working last call process.
   |  Finally, the authors would like to thank Ed Kern, the TEWG co-
   |  chair, for his comments and support.

   The early draft versions of this document were produced by the TEAS
   Working Group's RFC3272bis Design Team.  The full list of members of
   this team is:

      Acee Lindem
      Adrian Farrel
      Aijun Wang
      Daniele Ceccarelli
      Dieter Beller
      Jeff Tantsura
      Julien Meuric
      Liu Hua
      Loa Andersson
      Luis Miguel Contreras
      Martin Horneffer
      Tarek Saad
      Xufeng Liu

   The production of this document includes a fix to the original text
   resulting from an errata report #309 [Err309] by Jean-Michel
   Grimaldi.

   The editor of this document would also like to thank Dhruv Dhody,
   Gyan Mishra, Joel Halpern, Dave Taht, John Scudder, Rich Salz, Behcet
   Sarikaya, Bob Briscoe, Erik Kline, Jim Guichard, Martin Duke, and
   Roman Danyliw for review comments.

   This work is partially supported by the European Commission under
   Horizon 2020 grant agreement number 101015857 Secured autonomic
   traffic management for a Tera of SDN flows (Teraflow).

Contributors

   The following people contributed substantive text to this document:

   Gert Grammel
   Email: ggrammel@juniper.net


   Loa Andersson
   Email: loa@pi.nu


   Xufeng Liu
   Email: xufeng.liu.ietf@gmail.com


   Lou Berger
   Email: lberger@labn.net


   Jeff Tantsura
   Email: jefftant.ietf@gmail.com


   Daniel King
   Email: daniel@olddog.co.uk


   Boris Hassanov
   Email: bhassanov@yandex-team.ru


   Kiran Makhijani
   Email: kiranm@futurewei.com


   Dhruv Dhody
   Email: dhruv.ietf@gmail.com


   Mohamed Boucadair
   Email: mohamed.boucadair@orange.com


Author's Address