Rfc3815
TitleDefinitions of Managed Objects for the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP)
AuthorJ. Cucchiara, H. Sjostrand, J. Luciani
DateJune 2004
Format:TXT, HTML
Status:PROPOSED STANDARD






Network Working Group                                       J. Cucchiara
Request for Comments: 3815                  Marconi Communications, Inc.
Category: Standards Track                                   H. Sjostrand
                                                             ipUnplugged
                                                              J. Luciani
                                            Marconi Communications, Inc.
                                                               June 2004


                 Definitions of Managed Objects for the
                 Multiprotocol Label Switching (MPLS),
                   Label Distribution Protocol (LDP)

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2004).

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes managed objects for the Multiprotocol
   Label Switching, Label Distribution Protocol (LDP).


Table of Contents

   1.   Introduction. . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.   The Internet-Standard Management Framework. . . . . . . . . .  3
   3.   Structure of the MIB Modules. . . . . . . . . . . . . . . . .  3
        3.1.  Overview. . . . . . . . . . . . . . . . . . . . . . . .  3
        3.2.  Future Considerations . . . . . . . . . . . . . . . . .  4
        3.3.  Interface Indexing. . . . . . . . . . . . . . . . . . .  4
        3.4.  Differences from the LDP Specification. . . . . . . . .  4
        3.5.  The MPLS-LDP-STD-MIB Module . . . . . . . . . . . . . .  5
              3.5.1.  LDP Scalar Objects. . . . . . . . . . . . . . .  5
              3.5.2.  The LDP Entity Table. . . . . . . . . . . . . .  6
                      3.5.2.1.  Changing Values After Session
                                Establishment . . . . . . . . . . . .  6
              3.5.3.  The LDP Entity Statistics Table . . . . . . . .  7



RFC 3815                      MPLS LDP MIB                     June 2004


              3.5.4.  The LDP Peer Table. . . . . . . . . . . . . . .  7
              3.5.5.  The LDP Session Table . . . . . . . . . . . . .  8
              3.5.6.  The LDP Session Statistics Table. . . . . . . .  8
              3.5.7.  The LDP Hello Adjacency Table . . . . . . . . .  8
              3.5.8.  The LDP LSP Tables. . . . . . . . . . . . . . .  8
              3.5.9.  The FEC Tables. . . . . . . . . . . . . . . . .  9
              3.5.10. The LDP Session Peer Address Table. . . . . . .  9
        3.6.  LDP Notifications . . . . . . . . . . . . . . . . . . .  9
        3.7.  LDP Notification Frequency. . . . . . . . . . . . . . . 10
   4.   MPLS Label Distribution Protocol MIB Definitions. . . . . . . 10
        4.1.  The MPLS-LDP-ATM-STD-MIB Module . . . . . . . . . . . . 60
              4.1.1.  The LDP Entity ATM Table. . . . . . . . . . . . 61
              4.1.2.  The LDP Entity ATM Label Range Table. . . . . . 61
              4.1.3.  The LDP ATM Session Table . . . . . . . . . . . 61
        4.2.  The MPLS-LDP-FRAME-RELAY-STD-MIB Module . . . . . . . . 77
              4.2.1.  The LDP Entity Frame Relay Table. . . . . . . . 77
              4.2.2.  The LDP Entity Frame Relay Label Range Table. . 77
              4.2.3.  The LDP Frame Relay Session Table . . . . . . . 77
        4.3.  The MPLS-LDP-GENERIC-STD-MIB Module . . . . . . . . . . 91
   5.   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 98
   6.   References. . . . . . . . . . . . . . . . . . . . . . . . . . 98
        6.1.  Normative References. . . . . . . . . . . . . . . . . . 98
        6.2.  Informative References. . . . . . . . . . . . . . . . .100
   7.   Security Considerations . . . . . . . . . . . . . . . . . . .100
        7.1.  Security Considerations for MPLS-LDP-STD-MIB. . . . . .100
        7.2.  Security Considerations for MPLS-LDP-ATM-STD-MIB. . . .101
        7.3.  Security Considerations for
              MPLS-LDP-FRAME-RELAY-STD-MIB. . . . . . . . . . . . . .102
        7.4.  Security Considerations for MPLS-LDP-GENERIC-STD-MIB. .103
        7.5.  Additional Security Considerations. . . . . . . . . . .103
   8.   IANA Considerations . . . . . . . . . . . . . . . . . . . . .104
        8.1.  IANA Considerations for MPLS-LDP-STD-MIB. . . . . . . .104
        8.2.  IANA Considerations for MPLS-LDP-ATM-STD-MIB. . . . . .104
        8.3.  IANA Considerations for MPLS-LDP-FRAME-RELAY-STD-MIB. .104
        8.4.  IANA Considerations for MPLS-LDP-GENERIC-STD-MIB. . . .104
   9.   Authors' Addresses. . . . . . . . . . . . . . . . . . . . . .105
   10.  Full Copyright Statement. . . . . . . . . . . . . . . . . . .106

1.  Introduction

   This document defines 4 MIB Modules which together support the
   configuration and monitoring of the Label Distribution Protocol
   (LDP).  The Label Distribution Protocol (LDP) [RFC3036] is one type
   of Multiprotocol Label Switching (MPLS) protocols described in
   [RFC3031] and [RFC3032].  Utilizing all 4 MIB Modules allows an
   operator to configure LDP sessions using 3 different Layer 2 media.
   The Layer 2 media supported by the MIB Modules are Ethernet, ATM and
   Frame Relay as described in [RFC3036], [RFC3034] and [RFC3035].



RFC 3815                      MPLS LDP MIB                     June 2004


   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

   For an introduction to the concepts of MPLS, see [RFC3031].  For
   further on LDP refer to [RFC3037] and [RFC3215].

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

3.  Structure of the MIB Modules

   This section describes the structure of the LDP MIB Modules.

3.1.  Overview

   There are 4 MIB Modules in this document.  These MIB Modules are the
   MPLS-LDP-STD-MIB, the MPLS-LDP-GENERIC-STD-MIB, the MPLS-LDP-ATM-STD-
   MIB and the MPLS-LDP-FRAME-RELAY-STD-MIB.  The MPLS-LDP-STD-MIB
   defines objects which are common to all LDP implementations.  The
   MPLS-LDP-GENERIC-STD-MIB defines Layer 2 Per Platform Label Space
   objects for use with the MPLS-LDP-STD-MIB.  The MPLS-LDP-ATM-STD-MIB
   defines Layer 2 Asynchronous Transfer Mode (ATM) objects for use with
   the MPLS-LDP-STD-MIB.  The MPLS-LDP-FRAME-RELAY-STD-MIB defines Layer
   2 FRAME-RELAY objects for use with the MPLS-LDP-STD-MIB.

   The MPLS-LDP-STD-MIB Module MUST be implemented and at least one of
   the Layer 2 MIB Modules MUST be implemented by an Agent developer on
   an Label Switching Router (LSR) or Label Edge Router (LER).  As an
   example, if a Label Switching Router (LSR) or Label Edge Router (LER)
   implementation intends to support LDP utilizing a Layer 2 of
   Ethernet, then the MPLS-LDP-STD-MIB and the MPLS-LDP-GENERIC-STD-MIB
   Modules MUST implemented.  If an LSR/LER implementation intends to
   support LDP utilizing a Layer 2 of ATM, then the MPLS-LDP-STD-MIB
   Module and the MPLS-LDP-ATM-MIB Module MUST be implemented.  If an
   LSR/LER implementation intends to support LDP utilizing a Layer 2 of



RFC 3815                      MPLS LDP MIB                     June 2004


   FRAME-RELAY, then the MPLS-LDP-STD-MIB Module and the MPLS-LDP-FRAME-
   RELAY-STD-MIB Module MUST be implemented.  An LDP implementation that
   utilizes all three Layer 2 media (Ethernet, Frame-Relay, ATM) MUST
   support all 4 MIB Modules.  Each of the Modules will be discussed in
   detail in the following sections.

   There are 2 compliance statements for each MIB Module.  One
   compliance statement is for full compliance which allows both
   configuration and monitoring via SNMP.  The other compliance
   statement is for read-only compliance which allows only monitoring
   via SNMP.

3.2.  Future Considerations

   The LDP Specification [RFC3036] does not specify the use of VPNs or
   multicast for LDP, and thus, objects related to these areas have not
   been included.

   [RFC2684] does not describe VP merge capability and so this feature
   has not been included.

   These areas need to be specified in the LDP Specification or other
   specifications prior to being added in this or any other MIB
   document.

3.3.  Interface Indexing

   Interface Indexes as specified in [RFC2863] are used in these MIB
   Modules.  The descriptions of the ifIndexes denote which ifIndex is
   being used.  The use of ifIndex is for actual existing connections.

3.4.  Differences from the LDP Specification

   Currently, there are 3 differences between this specification and the
   LDP Specification.  As described in the Introduction, this document
   is almost entirely based on the LDP specification.  The differences
   are documented here.

   The first difference is that the LDP Entity Table contains some
   DEFVAL clauses which are not specified explicitly in the LDP
   Specification.  These values, although not documented in the LDP
   Specification, are widely used by existing LDP MIB implementations
   and thus, have been adopted within this MPLS-LDP-STD-MIB module.
   Please note, they can certainly be changed during row creation or a
   subsequent SET request.






RFC 3815                      MPLS LDP MIB                     June 2004


   A second difference is the mplsLdpEntityGenericLRTable in the MPLS-
   LDP-GENERIC-STD-MIB Module.  This table, although provided as a way
   to reserve a range of generic labels, does not exist in the LDP
   Specification.  It was added to the MIB due to a request from the
   working group and because this table was considered useful for
   reserving a range of generic labels.

   The third difference is documented by the TEXTUAL-CONVENTION,
   MplsAtmVcIdentifier which is in the MPLS-TC-STD-MIB [RFC3811].  This
   TC was added to restrict vci values to be greater than 31 as
   described in RFC 3035 [RFC3035].

3.5.  The MPLS-LDP-STD-MIB Module

   This MIB Module contains objects which are common to all LDP
   implementations.  This MIB Module MUST always be implemented along
   with one or more of the Layer 2 MIB Modules.  This MIB Module IMPORTS
   IndexInteger and IndexIntegerNextFree TEXTUAL-CONVENTIONs from
   [RFC3289], and IMPORTS InetAddressPrefixLength, InetAddressType,
   InetAddressInetPortNumber TEXTUAL-CONVENTIONs from [RFC3291].

   The mplsLdpEntityTable table allows the Label Edge Router (LER) or
   the Label Switching Router (LSR) to initiate and/or receive requests
   to establish LDP sessions.  As the LDP protocol distributes labels
   and establishes sessions with Peers most of the tables in this module
   are populated by the agent as instructed by the LDP protocol.  The
   exception is the mplsFecTable and the mplsLdpLspFecTable which can be
   configured by the operator to specify Forwarding Equivalence Class
   information for an LSP.

   Some scalars and each table in the MPLS-LDP-STD-MIB Module are
   described in the following subsections.

3.5.1.  LDP Scalar Objects

   There are several scalar objects in the LDP MIB module.  The
   mplsLdpLsrId is a read-only scalar object which reports Label
   Switching Router's (LSR's) Identifier.  This MUST be a globally
   unique value, such as the 32-bit router ID assigned to the LSR.

   The mplsLdpLsrLoopDetectionCapable scalar object denotes whether the
   LSR is capable of supporting loop detection and if so, which form of
   loop detection.








RFC 3815                      MPLS LDP MIB                     June 2004


   There are two LastChange scalar objects, mplsLdpEntityLastChange and
   mplsLdpPeerLastChange.  These objects give an indication of there was
   a change in the number of entries in the table, or if any of the
   values in the respective tables changed.  Please see the object's
   description for more details.

   The mplsLdpEntityIndexNext scalar object is described in the next
   section.

3.5.2.  The LDP Entity Table

   The MPLS-LDP-STD-MIB provides objects to configure/set-up potential
   LDP sessions on a specific LSR/LER.  The mplsLdpEntityTable is used
   to configure information which is used by the LDP protocol to setup
   potential LDP Sessions.

   Each entry/row in this table represents a single LDP Entity.  There
   is no maximum number of LDP Entities specified.  However, there is an
   mplsLdpEntityIndexNext object which should be retrieved by the
   command generator prior to creating an LDP Entity.  If the
   mplsLdpEntityIndexNext object is zero, this indicates that the
   LSR/LER is not able to create another LDP Entity at that time.

3.5.2.1.  Changing Values After Session Establishment

   One way to manually modify a session's parameters is by using SNMP to
   change the MIB objects related to that session.  Please note, special
   care should be taken if MIB objects which are used in the MPLS LDP
   Session Initialization need to be modified.  If the modification of
   any of these MIB variables takes place anytime after the start of
   session intialization, then the entire session must be halted.  Any
   information learned by that session must be discarded.  The objects
   should then be modified, and session initialization started.
   Assuming that the configuration was done correctly, then a new
   session will be created.

   For example, assume that an operator wishes to change the
   configuration of a Label Range which is used by a Session that has
   already been established.  The operator should change the
   mplsLdpEntityAdminStatus to "disable(2)".  Setting the
   mplsLdpEntityAdminStatus to "disable(2)" will cause the session to be
   torn down (i.e., this will signal to LDP that it should send out tear
   down messages for that session).  Also, all information related to
   that session should be removed from this MIB by the Agent.  This
   includes Peer information (i.e., relevant row in the mplsPeerTable)
   and Session statistics (i.e., relevant row in the
   mplsLdpSessionTable).  Also, if the MPLS-LSR-STD-MIB module [RFC3813]
   is implemented and the optional Mapping Table objects are



RFC 3815                      MPLS LDP MIB                     June 2004


   implemented, then all information related to the LSPs in this session
   should be removed from these MIB modules. [For more information
   please see the section on "The Mapping Tables".]  At this point, the
   operator could modify the Label Range.  Lastly, the operator should
   set the mplsLdpEntityAdminStatus to "enable(1)".  At this point
   session initialization should occur.  The LDP Entity goes through the
   Session Initialization in order to communicate the new Label Ranges
   to the Peer and establish new LSPs.

3.5.3.  The LDP Entity Statistics Table

   The mplsLpdEntityStatsTable is a read-only table which contains
   statistical information related to failed attempts to establish
   sessions.  Each row in this table AUGMENTS an mplsLdpEntityEntry.
   This table could be used to give insight into how to reconfigure
   values so that a session could be successfully established.  For
   example, if the mplsLdpEntityStatsSessionRejectedLRErrors Counter
   object was increasing, then this would indicate that the Label Range
   (LR) may need to be adjusted.

3.5.4.  The LDP Peer Table

   The mplsLdpPeerTable is a read-only table which contains information
   about LDP Peers known to LDP Entities.  In other words, the Peer
   information is learned by LDP through initialization or discovery.
   This table should be populated by the agent as directed by the LDP
   protocol.

   A row in this table is related to one or more rows in the Hello
   Adjacency Table and related to a single row in the Session Table.
   The values in the Peer table are specific to a Peer and may or may
   not be the same values used in the session.  The reason is that the
   Peer and Entity negotiate certain values.  The Entity's values are
   configured in the mplsLdpEntityTable and the Peer's values are
   learned (and placed into the mplsLdpPeerTable).  The
   mplsLdpSessionTable shows the values used in establishing the
   session.

   One example, of when the Peer's values and the Session's values may
   differ is with the Peer's Path Limit information.  The Peer's Path
   Limit information is learned from the session initialization phase.
   The actual value for the Path Vector Limit is the Peer's value and
   may not be the same value that appears in the session.  There could
   be a mismatch in this value between the Entity and the Peer.  In the
   event of a mismatch, then the session will use the Path Limit set by
   the Entity (and not the Peer).





RFC 3815                      MPLS LDP MIB                     June 2004


   The Peer Table information was placed in a separate table from the
   Session information to allow for a more comprehensive and coherent
   MIB model.

3.5.5.  The LDP Session Table

   The mplsLdpSessionTable is a read-only table.  Each entry in this
   table represents a single session between an LDP Entity and a Peer.
   The mplsLdpSessionEntry AUGMENTS the mplsLdpPeerEntry.

   The information in this table is learned during session
   establishment.  NOTE: rows in this table will appear during session
   intialization.

3.5.6.  The LDP Session Statistics Table

   The mplsLdpSessionStatsTable is a read-only table which contains
   statistical information on sessions.  This table AUGMENTS the
   mplsLdpPeerTable.

3.5.7.  The LDP Hello Adjacency Table

   This is a table of all adjacencies between all LDP Entities and all
   LDP Peers.  A Session may have one or more adjacencies.  A session
   should not have zero adjacencies, because this indicates that the
   session has lost contact with the Peer.  A session which has zero
   Hello Adjacencies should be removed.

3.5.8.  The LDP LSP Tables

   The Label Information Base (LIB) contains information about labels
   learned by the LSR.  The LIB for LDP, CR-LDP and MPLS-RSVP (i.e., all
   currently defined MPLS protocols) is represented in the LSR MIB
   [RFC3813].  The LIB is represented by the LSR MIB's mplsXCTable (mpls
   Cross Connect Table), mplsInSegmentTable (mpls In Segment Table) and
   the mplsOutSegmentTable (mpls Out Segment Table).  The mplsXCTable
   models the cross-connection of the incoming label with a specific
   outgoing label.  The mplsInSegmentTable stores the incoming label's
   information, and the mplsOutSegmentTable stores the outgoing label's
   information.

   The LDP Session that created the LSP and the LSP's (incoming label,
   outgoing label) pair along with other information is contained in the
   MPLS-LSR-STD-MIB module's mplsXCTable, the mplsInSegmentTable and the
   mplsOutSegmentTable.






RFC 3815                      MPLS LDP MIB                     June 2004


   In order to utilize the MPLS-LSR-STD-MIB module's mplsXCTable,
   mplsInSegmentTable and mplsOutSegmentTable for LDP LSPs, there needs
   to be a mechanism to associate LDP sessions with LDP LSPs created as
   a result of those LDP sessions.  The mplsInSegmentLdpLspTable and
   mplsOutSegmentLdpLspTable in this MIB contain information to find the
   LDP LSP entries in the mplsInSegmentTable, mplsOutSegmentTable and
   the mplsXCTable.

   These two tables, the mplsInSegmentLdpLspTable and
   mplsOutSegmentLdpLspTable, have been made optional in the conformance
   section of the MIB.  They only need to be supported if the LSR MIBs
   mplsInSegmentTable, mplsOutSegmentTable and mplsXCTable are
   implemented.

   As discussed in the section, "Changing Values after Session
   Establishment", if a session is torn down, then all the information
   related to this session, must be removed from the both LDP MIB and,
   if implemented, from the LSR MIB.

3.5.9.  The FEC Tables

   The mplsLdpFecTable is a table which contains FEC (Forwarding
   Equivalence Class) information.  Each entry/row represents a single
   FEC Element.  There is also an LDP LSP FEC Table, mplsLdpLspFecTable,
   which associates FECs with the LSPs.

3.5.10.  The LDP Session Peer Address Table

   The mplsLdpSessionPeerAddrTable is a table which extends the
   mplsLdpSessionTable.  This table is a read-only table which stores
   Addresses learned after session initialization via Address Message
   advertisement.

3.6.  LDP Notifications

   Currently, there are several notifications which are specific for
   LDP.  These are described in this section.  There are no objects
   which enable or disable notifications from being generated.  RFC 3413
   [RFC3413] contains MIB modules which can be implemented that will
   enable or disable these notifications from being generated.

   The mplsLdpInitSessionThresholdExceeded notification indicates to the
   operator that there may be a misconfigured mplsLdpEntityEntry because
   the session associated with this Entity is not being established, and
   the Entity keeps trying to establish the session.  A side effect of
   this situation is that a row in the mplsLdpSessionTable may not be
   reaching the operational state as indicated by the
   mplsLdpSessionState object.  If the value of



RFC 3815                      MPLS LDP MIB                     June 2004


   mplsLdpEntityInitSessionThreshold is 0 (zero) then this is equal to
   specifying the value of infinity for the threshold, and the
   mplsLdpInitSessionThresholdExceeded notification will never be sent.

   The mplsLdpPathVectorLimitMismatch notification is generated when
   there is a mismatch in the Path Vector Limits between the Entity and
   Peer during session initialization.  The session uses the value which
   is configured as the Entity's Path Vector Limit.  However, a
   notification should be generated to indicate that a mismatch
   occurred.  For further details, please see Section 3.5.3 of the LDP
   Specification [RFC3036].

   The mplsLdpSessionUp and mplsLdpSessionDown notifications are
   generated when there is an appropriate change in the
   mplsLdpSessionState object, e.g., when sessions change state (Up to
   Down for the mplsLdpSessionDown notification, or Down to Up for the
   mplsLdpSessionUp notification).  There was discussion about combining
   these two notifications into a single notification, however, some NMS
   applications can utilize two different notifications, rather than
   having to parse the varbind list of a single notification.  For
   example, the SessionDown is matched to a SessionUp notification more
   easily by some NMS applications, than having to parse a Varbind list
   in a SessionChange type of notification.

3.7.  LDP Notification Frequency

   LDP Notifications are expected to be few in number when LDP is
   ubiquitously deployed in a relatively stable network.  A notification
   receiver, e.g., an NMS, that receives these notifications should not
   be overwhelmed by the frequency of LDP notifications.  If this
   assertion proves to be inaccurate, then a throttling object to
   throttle these notifications may be added to future versions of the
   MPLS-LDP-STD-MIB.

4.  MPLS Label Distribution Protocol MIB Definitions

     MPLS-LDP-STD-MIB DEFINITIONS ::= BEGIN

     IMPORTS
         OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE,
         Integer32, Counter32, Unsigned32
             FROM SNMPv2-SMI                                -- [RFC2578]

         MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
             FROM SNMPv2-CONF                              --  [RFC2580]

         RowStatus, TimeInterval, TruthValue,
         TimeStamp, StorageType



RFC 3815                      MPLS LDP MIB                     June 2004


             FROM SNMPv2-TC                                --  [RFC2579]

         InetAddressPrefixLength,
         InetAddressType,
         InetAddress,
         InetPortNumber
             FROM INET-ADDRESS-MIB                         --  [RFC3291]

         IndexInteger,
         IndexIntegerNextFree
             FROM DIFFSERV-MIB                             --  [RFC3289]

         mplsStdMIB,
         MplsLabelDistributionMethod,
         MplsLdpIdentifier,
         MplsLdpLabelType,
         MplsLspType,
         MplsLsrIdentifier,
         MplsRetentionMode
             FROM MPLS-TC-STD-MIB                          --  [RFC3811]

         MplsIndexType
             FROM MPLS-LSR-STD-MIB;                        --  [RFC3813]

     mplsLdpStdMIB MODULE-IDENTITY
         LAST-UPDATED "200406030000Z"  -- June 3, 2004
         ORGANIZATION "Multiprotocol Label Switching (mpls)
                       Working Group"
         CONTACT-INFO

             "Joan Cucchiara (jcucchiara@mindspring.com)
              Marconi Communications, Inc.

              Hans Sjostrand (hans@ipunplugged.com)
              ipUnplugged

              James V. Luciani (james_luciani@mindspring.com)
              Marconi Communications, Inc.

              Working Group Chairs:
              George Swallow,   email: swallow@cisco.com
              Loa Andersson,    email: loa@pi.se

              MPLS Working Group, email: mpls@uu.net"

         DESCRIPTION
             "Copyright (C) The Internet Society (2004). The
             initial version of this MIB module was published



RFC 3815                      MPLS LDP MIB                     June 2004


             in RFC 3815. For full legal notices see the RFC
             itself or see:
             http://www.ietf.org/copyrights/ianamib.html

             This MIB contains managed object definitions for the
             'Multiprotocol Label Switching, Label Distribution
             Protocol, LDP' document."

         REVISION "200406030000Z"  -- June 3, 2004
         DESCRIPTION
            "Initial version published as part of RFC 3815."

         ::= { mplsStdMIB 4 }

     --****************************************************************

     mplsLdpNotifications OBJECT IDENTIFIER ::= { mplsLdpStdMIB 0 }
     mplsLdpObjects       OBJECT IDENTIFIER ::= { mplsLdpStdMIB 1 }
     mplsLdpConformance   OBJECT IDENTIFIER ::= { mplsLdpStdMIB 2 }

     --****************************************************************
     -- MPLS LDP Objects
     --****************************************************************

     mplsLdpLsrObjects    OBJECT IDENTIFIER ::= { mplsLdpObjects 1 }

     mplsLdpEntityObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 2 }

     --
     -- The MPLS Label Distribution Protocol's
     -- Label Switching Router Objects
     --

     mplsLdpLsrId OBJECT-TYPE
         SYNTAX      MplsLsrIdentifier
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The Label Switching Router's Identifier."
         ::= { mplsLdpLsrObjects 1 }

     mplsLdpLsrLoopDetectionCapable OBJECT-TYPE
         SYNTAX      INTEGER {
                                none(1),
                                other(2),
                                hopCount(3),
                                pathVector(4),
                                hopCountAndPathVector(5)



RFC 3815                      MPLS LDP MIB                     June 2004


                             }
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "A indication of whether this
             Label Switching Router supports
             loop detection.

             none(1) -- Loop Detection is not supported
                        on this LSR.

             other(2) -- Loop Detection is supported but
                         by a method other than those
                         listed below.

             hopCount(3) -- Loop Detection is supported by
                            Hop Count only.

             pathVector(4) -- Loop Detection is supported by
                              Path Vector only.

             hopCountAndPathVector(5) -- Loop Detection is
                                  supported by both Hop Count
                                  And Path Vector.

             Since Loop Detection is determined during
             Session Initialization, an individual session
             may not be running with loop detection.  This
             object simply gives an indication of whether or not the
             LSR has the ability to support Loop Detection and
             which types."

         ::= { mplsLdpLsrObjects 2 }

     --
     -- The MPLS Label Distribution Protocol Entity Objects
     --

     mplsLdpEntityLastChange OBJECT-TYPE
         SYNTAX  TimeStamp
         MAX-ACCESS read-only
         STATUS current
         DESCRIPTION
             "The value of sysUpTime at the time of the most
             recent addition or deletion of an entry
             to/from the mplsLdpEntityTable/mplsLdpEntityStatsTable, or
             the most recent change in value of any objects in the
             mplsLdpEntityTable.



RFC 3815                      MPLS LDP MIB                     June 2004


             If no such changes have occurred since the last
             re-initialization of the local management subsystem,
             then this object contains a zero value."
         ::= { mplsLdpEntityObjects 1 }

     mplsLdpEntityIndexNext  OBJECT-TYPE
         SYNTAX      IndexIntegerNextFree
         MAX-ACCESS     read-only
         STATUS         current
         DESCRIPTION
             "This object contains an appropriate value to
             be used for mplsLdpEntityIndex when creating
             entries in the mplsLdpEntityTable. The value
             0 indicates that no unassigned entries are
             available."
        ::= { mplsLdpEntityObjects 2 }


     mplsLdpEntityTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsLdpEntityEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "This table contains information about the
             MPLS Label Distribution Protocol Entities which
             exist on this Label Switching Router (LSR)
             or Label Edge Router (LER)."
          ::= { mplsLdpEntityObjects 3 }

      mplsLdpEntityEntry OBJECT-TYPE
          SYNTAX      MplsLdpEntityEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION
              "An entry in this table represents an LDP entity.
              An entry can be created by a network administrator
              or by an SNMP agent as instructed by LDP."
          INDEX       {  mplsLdpEntityLdpId, mplsLdpEntityIndex  }
          ::= { mplsLdpEntityTable 1 }

      MplsLdpEntityEntry ::= SEQUENCE {
          mplsLdpEntityLdpId                MplsLdpIdentifier,
          mplsLdpEntityIndex                IndexInteger,
          mplsLdpEntityProtocolVersion      Unsigned32,
          mplsLdpEntityAdminStatus          INTEGER,
          mplsLdpEntityOperStatus           INTEGER,
          mplsLdpEntityTcpPort              InetPortNumber,
          mplsLdpEntityUdpDscPort           InetPortNumber,



RFC 3815                      MPLS LDP MIB                     June 2004


          mplsLdpEntityMaxPduLength         Unsigned32,
          mplsLdpEntityKeepAliveHoldTimer   Unsigned32,
          mplsLdpEntityHelloHoldTimer       Unsigned32,
          mplsLdpEntityInitSessionThreshold Integer32,
          mplsLdpEntityLabelDistMethod      MplsLabelDistributionMethod,
          mplsLdpEntityLabelRetentionMode   MplsRetentionMode,
          mplsLdpEntityPathVectorLimit      Integer32,
          mplsLdpEntityHopCountLimit        Integer32,
          mplsLdpEntityTransportAddrKind    INTEGER,
          mplsLdpEntityTargetPeer           TruthValue,
          mplsLdpEntityTargetPeerAddrType   InetAddressType,
          mplsLdpEntityTargetPeerAddr       InetAddress,
          mplsLdpEntityLabelType            MplsLdpLabelType,
          mplsLdpEntityDiscontinuityTime    TimeStamp,
          mplsLdpEntityStorageType          StorageType,
          mplsLdpEntityRowStatus            RowStatus
      }

      mplsLdpEntityLdpId OBJECT-TYPE
          SYNTAX      MplsLdpIdentifier
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION
              "The LDP identifier."
         REFERENCE
             "RFC3036, LDP Specification, Section on LDP Identifiers."
         ::= { mplsLdpEntityEntry 1 }

     mplsLdpEntityIndex OBJECT-TYPE
         SYNTAX      IndexInteger
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "This index is used as a secondary index to uniquely
             identify this row.  Before creating a row in this table,
             the 'mplsLdpEntityIndexNext' object should be retrieved.
             That value should be used for the value of this index
             when creating a row in this table.  NOTE:  if a value
             of zero (0) is retrieved, that indicates that no rows
             can be created in this table at this time.

             A secondary index (this object) is meaningful to some
             but not all, LDP implementations.  For example
             an LDP implementation which uses PPP would
             use this index to differentiate PPP sub-links.

             Another way to use this index is to give this the
             value of ifIndex.  However, this is dependant



RFC 3815                      MPLS LDP MIB                     June 2004


             on the implementation."
         ::= { mplsLdpEntityEntry 2 }

     mplsLdpEntityProtocolVersion OBJECT-TYPE
         SYNTAX      Unsigned32(1..65535)
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
            "The version number of the LDP protocol which will be
            used in the session initialization message.

            Section 3.5.3 in the LDP Specification specifies
            that the version of the LDP protocol is negotiated during
            session establishment. The value of this object
            represents the value that is sent in the initialization
            message."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.3 Initialization
            Message."
         DEFVAL { 1 }
         ::= { mplsLdpEntityEntry 3 }

     mplsLdpEntityAdminStatus OBJECT-TYPE
         SYNTAX      INTEGER {
                       enable(1),
                       disable(2)
                     }
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The administrative status of this LDP Entity.
             If this object is changed from 'enable' to 'disable'
             and this entity has already attempted to establish
             contact with a Peer, then all contact with that
             Peer is lost and all information from that Peer
             needs to be removed from the MIB. (This implies
             that the network management subsystem should clean
             up any related entry in the mplsLdpPeerTable.  This
             further implies that a 'tear-down' for that session
             is issued and the session and all information related
             to that session cease to exist).

             At this point the operator is able to change values
             which are related to this entity.

             When the admin status is set back to 'enable', then
             this Entity will attempt to establish a new session
             with the Peer."



RFC 3815                      MPLS LDP MIB                     June 2004


         DEFVAL  { enable }
         ::= { mplsLdpEntityEntry 4 }

     mplsLdpEntityOperStatus OBJECT-TYPE
         SYNTAX      INTEGER {
                       unknown(1),
                       enabled(2),
                       disabled(3)
                     }
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The operational status of this LDP Entity.

             The value of unknown(1) indicates that the
             operational status cannot be determined at
             this time.  The value of unknown should be
             a transient condition before changing
             to enabled(2) or disabled(3)."
         ::= { mplsLdpEntityEntry 5 }

     mplsLdpEntityTcpPort OBJECT-TYPE
         SYNTAX      InetPortNumber
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The TCP Port for
             LDP.  The default value is the well-known
             value of this port."
         REFERENCE
             "RFC3036, LDP Specification, Section 3.10, Well-known
              Numbers, and Section 3.10.1.  UDP and TCP Ports."
         DEFVAL { 646 }
         ::= { mplsLdpEntityEntry 6 }

     mplsLdpEntityUdpDscPort OBJECT-TYPE
         SYNTAX      InetPortNumber
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The UDP Discovery Port for
             LDP.  The default value is the
             well-known value for this port."
         REFERENCE
             "RFC3036, LDP Specification, Section 2.4.1,
             Basic Discovery Mechanism, Section 2.4.2,
             Extended Discovery Mechanism, Section
             3.10, Well-known Numbers, and Section 3.10.1.



RFC 3815                      MPLS LDP MIB                     June 2004


             UDP and TCP Ports."
         DEFVAL { 646 }
         ::= { mplsLdpEntityEntry 7 }

     mplsLdpEntityMaxPduLength OBJECT-TYPE
         SYNTAX      Unsigned32 (256..65535)
         UNITS       "octets"
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
            "The maximum PDU Length that is sent in
            the Common Session Parameters of an Initialization
            Message. According to the LDP Specification [RFC3036]
            a value of 255 or less specifies the
            default maximum length of 4096 octets, this is why
            the value of this object starts at 256.  The operator
            should explicitly choose the default value (i.e., 4096),
            or some other value.

            The receiving LSR MUST calculate the maximum PDU
            length for the session by using the smaller of its and
            its peer's proposals for Max PDU Length."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.3.
            Initialization Message."
         DEFVAL { 4096 }
         ::= { mplsLdpEntityEntry 8 }

     mplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE
         SYNTAX      Unsigned32 (1..65535)
         UNITS       "seconds"
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The 16-bit integer value which is the proposed keep
             alive hold timer for this LDP Entity."
         DEFVAL { 40 }
         ::= { mplsLdpEntityEntry 9 }

     mplsLdpEntityHelloHoldTimer OBJECT-TYPE
         SYNTAX      Unsigned32 (0..65535)
         UNITS       "seconds"
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The 16-bit integer value which is the proposed Hello
             hold timer for this LDP Entity. The Hello Hold time
             in seconds.



RFC 3815                      MPLS LDP MIB                     June 2004


             An LSR maintains a record of Hellos received
             from potential peers.  This object represents
             the Hold Time in the Common Hello Parameters TLV of
             the Hello Message.

             A value of 0 is a default value and should be
             interpretted in conjunction with the
             mplsLdpEntityTargetPeer object.

             If the value of this object is 0: if the value of the
             mplsLdpEntityTargetPeer object is false(2), then this
             specifies that the Hold Time's actual default value is
             15 seconds (i.e., the default Hold time for Link Hellos
             is 15 seconds).  Otherwise if the value of the
             mplsLdpEntityTargetPeer object is true(1), then this
             specifies that the Hold Time's actual default value is
             45 seconds (i.e., the default Hold time for Targeted
             Hellos is 45 seconds).

             A value of 65535 means infinite (i.e., wait forever).

             All other values represent the amount of time in
             seconds to wait for a Hello Message.  Setting the
             hold time to a value smaller than 15 is not
             recommended, although not forbidden according
             to RFC3036."
         REFERENCE
             "RFC3036, LDP Specification, Section 3.5.2.,
             Hello Message."
         DEFVAL { 0 }
         ::= { mplsLdpEntityEntry 10 }

     mplsLdpEntityInitSessionThreshold OBJECT-TYPE
         SYNTAX      Integer32(0..100)
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "When attempting to establish a session with
             a given Peer, the given LDP Entity should
             send out the SNMP notification,
             'mplsLdpInitSessionThresholdExceeded', when
             the number of Session Initialization messages
             sent exceeds this threshold.

             The notification is used to notify an
             operator when this Entity and its Peer are
             possibly engaged in an endless sequence
             of messages as each NAKs the other's



RFC 3815                      MPLS LDP MIB                     June 2004


             Initialization messages with Error Notification
             messages.  Setting this threshold which triggers
             the notification is one way to notify the
             operator.  The notification should be generated
             each time this threshold is exceeded and
             for every subsequent Initialization message
             which is NAK'd with an Error Notification
             message after this threshold is exceeded.

             A value of 0 (zero) for this object
             indicates that the threshold is infinity, thus
             the SNMP notification will never be generated."
         REFERENCE
             "RFC3036, LDP Specification,
             Section 2.5.3 Session Initialization."
         DEFVAL { 8 }
         ::= { mplsLdpEntityEntry 11 }

     mplsLdpEntityLabelDistMethod OBJECT-TYPE
         SYNTAX      MplsLabelDistributionMethod
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "For any given LDP session, the method of
             label distribution must be specified."
         ::= { mplsLdpEntityEntry 12 }

     mplsLdpEntityLabelRetentionMode OBJECT-TYPE
         SYNTAX      MplsRetentionMode
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The LDP Entity can be configured to use either
             conservative or liberal label retention mode.

             If the value of this object is conservative(1)
             then advertized label mappings are retained
             only if they will be used to forward packets,
             i.e., if label came from a valid next hop.

             If the value of this object is liberal(2)
             then all advertized label mappings are retained
             whether they are from a valid next hop or not."
         ::= { mplsLdpEntityEntry 13 }

     mplsLdpEntityPathVectorLimit OBJECT-TYPE
         SYNTAX      Integer32 (0..255)
         MAX-ACCESS  read-create



RFC 3815                      MPLS LDP MIB                     June 2004


         STATUS      current
         DESCRIPTION
             "If the value of this object is 0 (zero) then
             Loop Detection for Path Vectors is disabled.

             Otherwise, if this object has a value greater than
             zero, then Loop Dection for Path Vectors is enabled,
             and the Path Vector Limit is this value.
             Also, the value of the object,
             'mplsLdpLsrLoopDetectionCapable', must be set to
             either 'pathVector(4)' or 'hopCountAndPathVector(5)',
             if this object has a value greater than 0 (zero),
             otherwise it is ignored."
         REFERENCE
            "RFC3036, LDP Specification, Section 2.8 Loop Dection,
            Section 3.4.5 Path Vector TLV."
         ::= { mplsLdpEntityEntry 14 }

     mplsLdpEntityHopCountLimit OBJECT-TYPE
         SYNTAX       Integer32 (0..255)
         MAX-ACCESS   read-create
         STATUS       current
         DESCRIPTION
             "If the value of this object is 0 (zero),
             then Loop Detection using Hop Counters is
             disabled.

             If the value of this object is greater than
             0 (zero) then Loop Detection using Hop
             Counters is enabled, and this object
             specifies this Entity's maximum allowable
             value for the Hop Count.
             Also, the value of the object
             mplsLdpLsrLoopDetectionCapable must be set
             to either 'hopCount(3)' or
             'hopCountAndPathVector(5)' if this object
             has a value greater than 0 (zero), otherwise
             it is ignored."
         DEFVAL { 0 }
         ::= { mplsLdpEntityEntry 15 }

     mplsLdpEntityTransportAddrKind OBJECT-TYPE
         SYNTAX     INTEGER {
                               interface(1),
                               loopback(2)
                            }
         MAX-ACCESS read-create
         STATUS     current



RFC 3815                      MPLS LDP MIB                     June 2004


         DESCRIPTION
             "This specifies whether the loopback or interface
             address is to be used as the transport address
             in the transport address TLV of the
             hello message.

             If the value is interface(1), then the IP
             address of the interface from which hello
             messages are sent is used as the transport
             address in the hello message.

             Otherwise, if the value is loopback(2), then the IP
             address of the loopback interface is used as the
             transport address in the hello message."
         DEFVAL { loopback }
         ::= { mplsLdpEntityEntry 16 }

     mplsLdpEntityTargetPeer OBJECT-TYPE
         SYNTAX      TruthValue
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "If this LDP entity uses targeted peer then set
             this to true."
         DEFVAL { false }
         ::= { mplsLdpEntityEntry 17 }

     mplsLdpEntityTargetPeerAddrType OBJECT-TYPE
         SYNTAX      InetAddressType
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The type of the internetwork layer address used for
             the Extended Discovery.  This object indicates how
             the value of mplsLdpEntityTargetPeerAddr is to
             be interpreted."
         ::= { mplsLdpEntityEntry 18 }

     mplsLdpEntityTargetPeerAddr OBJECT-TYPE
         SYNTAX      InetAddress
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The value of the internetwork layer address
             used for the Extended Discovery.  The value of
             mplsLdpEntityTargetPeerAddrType specifies how
             this address is to be interpreted."
        ::= { mplsLdpEntityEntry 19 }



RFC 3815                      MPLS LDP MIB                     June 2004


     mplsLdpEntityLabelType OBJECT-TYPE
         SYNTAX      MplsLdpLabelType
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "Specifies the optional parameters for the LDP
             Initialization Message.

             If the value is generic(1) then no
             optional parameters will be sent in
             the LDP Initialization message associated
             with this Entity.

             If the value is atmParameters(2) then
             a row must be created in the
             mplsLdpEntityAtmTable, which
             corresponds to this entry.

             If the value is frameRelayParameters(3) then
             a row must be created in the
             mplsLdpEntityFrameRelayTable, which
             corresponds to this entry."
         REFERENCE
             "RFC3036, LDP Specification, Section 3.5.3.,
             Initialization Message."
         ::= { mplsLdpEntityEntry 20 }

     mplsLdpEntityDiscontinuityTime OBJECT-TYPE
         SYNTAX      TimeStamp
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The value of sysUpTime on the most recent occasion
             at which any one or more of this entity's counters
             suffered a discontinuity.  The relevant counters
             are the specific instances associated with this
             entity of any Counter32 object contained
             in the 'mplsLdpEntityStatsTable'.  If no such
             discontinuities have occurred since the last
             re-initialization of the local management
             subsystem, then this object contains a zero
             value."
         ::= { mplsLdpEntityEntry 21 }

     mplsLdpEntityStorageType  OBJECT-TYPE
         SYNTAX      StorageType
         MAX-ACCESS  read-create
         STATUS      current



RFC 3815                      MPLS LDP MIB                     June 2004


         DESCRIPTION
             "The storage type for this conceptual row.
             Conceptual rows having the value 'permanent(4)'
             need not allow write-access to any columnar
             objects in the row."
         DEFVAL{ nonVolatile }
         ::= { mplsLdpEntityEntry 22 }

     mplsLdpEntityRowStatus OBJECT-TYPE
         SYNTAX      RowStatus
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The status of this conceptual row.  All writable
              objects in this row may be modified at any
              time, however, as described in detail in
              the section entitled, 'Changing Values After
              Session Establishment', and again described
              in the DESCRIPTION clause of the
              mplsLdpEntityAdminStatus object, if a session
              has been initiated with a Peer, changing objects
              in this table will wreak havoc with the session
              and interrupt traffic.  To repeat again:
              the recommended procedure is to
              set the mplsLdpEntityAdminStatus to down, thereby
              explicitly causing a session to be torn down. Then,
              change objects in this entry, then set
              the mplsLdpEntityAdminStatus to enable,
              which enables a new session to be initiated."
         ::= { mplsLdpEntityEntry 23 }

     --
     -- The MPLS LDP Entity Statistics Table
     --

     mplsLdpEntityStatsTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsLdpEntityStatsEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "This table is a read-only table which augments
             the mplsLdpEntityTable.  The purpose of this
             table is to keep statistical information about
             the LDP Entities on the LSR."
         ::= { mplsLdpEntityObjects 4 }

     mplsLdpEntityStatsEntry OBJECT-TYPE
         SYNTAX      MplsLdpEntityStatsEntry



RFC 3815                      MPLS LDP MIB                     June 2004


         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "A row in this table contains statistical information
             about an LDP Entity.  Some counters contained in a
             row are for fatal errors received during a former
             LDP Session associated with this entry.  For example,
             an LDP PDU received on a TCP connection during an
             LDP Session contains a fatal error.  That
             error is counted here, because the
             session is terminated.

             If the error is NOT fatal (i.e., the Session
             remains), then the error is counted in the
             mplsLdpSessionStatsEntry."
         AUGMENTS       {   mplsLdpEntityEntry  }
         ::= { mplsLdpEntityStatsTable 1 }

     MplsLdpEntityStatsEntry ::= SEQUENCE {
         mplsLdpEntityStatsSessionAttempts               Counter32,
         mplsLdpEntityStatsSessionRejectedNoHelloErrors  Counter32,
         mplsLdpEntityStatsSessionRejectedAdErrors       Counter32,
         mplsLdpEntityStatsSessionRejectedMaxPduErrors   Counter32,
         mplsLdpEntityStatsSessionRejectedLRErrors       Counter32,
         mplsLdpEntityStatsBadLdpIdentifierErrors        Counter32,
         mplsLdpEntityStatsBadPduLengthErrors            Counter32,
         mplsLdpEntityStatsBadMessageLengthErrors        Counter32,
         mplsLdpEntityStatsBadTlvLengthErrors            Counter32,
         mplsLdpEntityStatsMalformedTlvValueErrors       Counter32,
         mplsLdpEntityStatsKeepAliveTimerExpErrors       Counter32,
         mplsLdpEntityStatsShutdownReceivedNotifications Counter32,
         mplsLdpEntityStatsShutdownSentNotifications     Counter32
     }

     mplsLdpEntityStatsSessionAttempts OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "A count of the Session Initialization messages
             which were sent or received by this LDP Entity and
             were NAK'd.   In other words, this counter counts
             the number of session initializations that failed.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."



RFC 3815                      MPLS LDP MIB                     June 2004


         ::= { mplsLdpEntityStatsEntry 1 }

     mplsLdpEntityStatsSessionRejectedNoHelloErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "A count of the Session Rejected/No Hello Error
             Notification Messages sent or received by
             this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         ::= { mplsLdpEntityStatsEntry 2 }

     mplsLdpEntityStatsSessionRejectedAdErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "A count of the Session Rejected/Parameters
             Advertisement Mode Error Notification Messages sent
             or received by this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         ::= { mplsLdpEntityStatsEntry 3 }

     mplsLdpEntityStatsSessionRejectedMaxPduErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "A count of the Session Rejected/Parameters

             Max Pdu Length Error Notification Messages sent
             or received by this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         ::= { mplsLdpEntityStatsEntry 4 }




RFC 3815                      MPLS LDP MIB                     June 2004


     mplsLdpEntityStatsSessionRejectedLRErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "A count of the Session Rejected/Parameters
             Label Range Notification Messages sent
             or received by this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         ::= { mplsLdpEntityStatsEntry 5 }

     mplsLdpEntityStatsBadLdpIdentifierErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Bad LDP Identifier
             Fatal Errors detected by the session(s)
             (past and present) associated with this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.1.2."
         ::= { mplsLdpEntityStatsEntry 6 }

     mplsLdpEntityStatsBadPduLengthErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Bad PDU Length
             Fatal Errors detected by the session(s)
             (past and present) associated with this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.1.2."
         ::= { mplsLdpEntityStatsEntry 7 }



RFC 3815                      MPLS LDP MIB                     June 2004


     mplsLdpEntityStatsBadMessageLengthErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Bad Message
             Length Fatal Errors detected by the session(s)
             (past and present) associated with this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.1.2."
         ::= { mplsLdpEntityStatsEntry 8 }

     mplsLdpEntityStatsBadTlvLengthErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Bad TLV
             Length Fatal Errors detected by the session(s)
             (past and present) associated with this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.1.2."
         ::= { mplsLdpEntityStatsEntry 9 }

     mplsLdpEntityStatsMalformedTlvValueErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Malformed TLV
             Value Fatal Errors detected by the session(s)
             (past and present) associated with this
             LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."



RFC 3815                      MPLS LDP MIB                     June 2004


         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.1.2."
         ::= { mplsLdpEntityStatsEntry 10 }

     mplsLdpEntityStatsKeepAliveTimerExpErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Session Keep Alive
             Timer Expired Errors detected by the session(s)
             (past and present) associated with this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.1.2."
         ::= { mplsLdpEntityStatsEntry 11 }

     mplsLdpEntityStatsShutdownReceivedNotifications OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Shutdown Notifications
             received related to session(s) (past and present)
             associated with this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpEntityDiscontinuityTime."
         ::= { mplsLdpEntityStatsEntry 12 }

     mplsLdpEntityStatsShutdownSentNotifications OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Shutdown Notfications
             sent related to session(s) (past and present) associated
             with this LDP Entity.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of



RFC 3815                      MPLS LDP MIB                     June 2004


             mplsLdpEntityDiscontinuityTime."
         ::= { mplsLdpEntityStatsEntry 13 }

     --
     -- The MPLS LDP Peer Table
     --

     mplsLdpSessionObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 3 }

     mplsLdpPeerLastChange OBJECT-TYPE
         SYNTAX  TimeStamp
         MAX-ACCESS read-only
         STATUS current
         DESCRIPTION
             "The value of sysUpTime at the time of the most
             recent addition or deletion to/from the
             mplsLdpPeerTable/mplsLdpSessionTable."
         ::= { mplsLdpSessionObjects 1 }

     mplsLdpPeerTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsLdpPeerEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "Information about LDP peers known by Entities in
             the mplsLdpEntityTable.  The information in this table
             is based on information from the Entity-Peer interaction
             during session initialization but is not appropriate
             for the mplsLdpSessionTable, because objects in this
             table may or may not be used in session establishment."
         ::= { mplsLdpSessionObjects 2 }

     mplsLdpPeerEntry OBJECT-TYPE
         SYNTAX      MplsLdpPeerEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "Information about a single Peer which is related
             to a Session.  This table is augmented by
             the mplsLdpSessionTable."
         INDEX       { mplsLdpEntityLdpId,
                       mplsLdpEntityIndex,
                       mplsLdpPeerLdpId }
         ::= { mplsLdpPeerTable 1 }

     MplsLdpPeerEntry ::= SEQUENCE {
         mplsLdpPeerLdpId                MplsLdpIdentifier,
         mplsLdpPeerLabelDistMethod      MplsLabelDistributionMethod,



RFC 3815                      MPLS LDP MIB                     June 2004


         mplsLdpPeerPathVectorLimit      Integer32,
         mplsLdpPeerTransportAddrType    InetAddressType,
         mplsLdpPeerTransportAddr        InetAddress
     }

     mplsLdpPeerLdpId OBJECT-TYPE
         SYNTAX      MplsLdpIdentifier
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "The LDP identifier of this LDP Peer."
         ::= { mplsLdpPeerEntry 1 }

     mplsLdpPeerLabelDistMethod OBJECT-TYPE
         SYNTAX      MplsLabelDistributionMethod
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "For any given LDP session, the method of
             label distribution must be specified."
         ::= { mplsLdpPeerEntry 2 }

     mplsLdpPeerPathVectorLimit OBJECT-TYPE
         SYNTAX      Integer32 (0..255)
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "If the value of this object is 0 (zero) then
             Loop Dection for Path Vectors for this Peer
             is disabled.

             Otherwise, if this object has a value greater than
             zero, then Loop Dection for Path  Vectors for this
             Peer is enabled and the Path Vector Limit is this value."
         REFERENCE
            "RFC3036, LDP Specification, Section 2.8 Loop Dection,
            Section 3.4.5 Path Vector TLV."
         ::= { mplsLdpPeerEntry 3 }

     mplsLdpPeerTransportAddrType OBJECT-TYPE
         SYNTAX      InetAddressType
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The type of the Internet address for the
             mplsLdpPeerTransportAddr object.  The LDP
             specification describes this as being either
             an IPv4 Transport Address or IPv6 Transport



RFC 3815                      MPLS LDP MIB                     June 2004


             Address which is used in opening the LDP session's
             TCP connection, or if the optional TLV is not
             present, then this is the IPv4/IPv6 source
             address for the UPD packet carrying the Hellos.

             This object specifies how the value of the
             mplsLdpPeerTransportAddr object should be
             interpreted."
         REFERENCE
            "RFC3036, LDP Specification, Section 2.5.2
            Transport Connection Establishment and
            Section 3.5.2.1 Hello Message Procedures."
         ::= { mplsLdpPeerEntry 4 }

     mplsLdpPeerTransportAddr OBJECT-TYPE
         SYNTAX      InetAddress
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The Internet address advertised by the peer
             in the Hello Message or the Hello source address.

             The type of this address is specified by the
             value of the mplsLdpPeerTransportAddrType
             object."
         REFERENCE
            "RFC3036, LDP Specification, Section 2.5.2
            Transport Connection Establishment and
            Section 3.5.2.1 Hello Message Procedures."
         ::= { mplsLdpPeerEntry 5 }

     --
     -- The MPLS LDP Sessions Table
     --

     mplsLdpSessionTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsLdpSessionEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "A table of Sessions between the LDP Entities
             and LDP Peers.  This table AUGMENTS the
             mplsLdpPeerTable.  Each row in this table
             represents a single session."
         ::= { mplsLdpSessionObjects 3 }

     mplsLdpSessionEntry OBJECT-TYPE
         SYNTAX      MplsLdpSessionEntry



RFC 3815                      MPLS LDP MIB                     June 2004


         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "An entry in this table represents information on a
             single session between an LDP Entity and LDP Peer.
             The information contained in a row is read-only.

             Please note:  the Path Vector Limit for the
             Session is the value which is configured in
             the corresponding mplsLdpEntityEntry. The
             Peer's Path Vector Limit is in the
             mplsLdpPeerPathVectorLimit object in the
             mplsLdpPeerTable.

             Values which may differ from those configured are
             noted in the objects of this table, the
             mplsLdpAtmSessionTable and the
             mplsLdpFrameRelaySessionTable. A value will
             differ if it was negotiated between the
             Entity and the Peer.  Values may or may not
             be negotiated.  For example, if the values
             are the same then no negotiation takes place.
             If they are negotiated, then they may differ."
         AUGMENTS { mplsLdpPeerEntry }
         ::= { mplsLdpSessionTable 1 }

     MplsLdpSessionEntry ::= SEQUENCE {
         mplsLdpSessionStateLastChange       TimeStamp,
         mplsLdpSessionState                 INTEGER,
         mplsLdpSessionRole                  INTEGER,
         mplsLdpSessionProtocolVersion       Unsigned32,
         mplsLdpSessionKeepAliveHoldTimeRem  TimeInterval,
         mplsLdpSessionKeepAliveTime         Unsigned32,
         mplsLdpSessionMaxPduLength          Unsigned32,
         mplsLdpSessionDiscontinuityTime     TimeStamp
     }

     mplsLdpSessionStateLastChange OBJECT-TYPE
         SYNTAX TimeStamp
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The value of sysUpTime at the time this
             Session entered its current state as
             denoted by the mplsLdpSessionState
             object."
         ::= { mplsLdpSessionEntry 1 }




RFC 3815                      MPLS LDP MIB                     June 2004


     mplsLdpSessionState OBJECT-TYPE
         SYNTAX      INTEGER {
                        nonexistent(1),
                        initialized(2),
                        openrec(3),
                        opensent(4),
                        operational(5)
                     }
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The current state of the session, all of the
             states 1 to 5 are based on the state machine
             for session negotiation behavior."
         REFERENCE
             "RFC3036, LDP Specification, Section 2.5.4,
             Initialization State Machine."
         ::= { mplsLdpSessionEntry 2 }

     mplsLdpSessionRole OBJECT-TYPE
         SYNTAX      INTEGER {
                        unknown(1),
                        active(2),
                        passive(3)
                     }
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "During session establishment the LSR/LER takes either
             the active role or the passive role based on address
             comparisons.  This object indicates whether this LSR/LER
             was behaving in an active role or passive role during
             this session's establishment.

             The value of unknown(1), indicates that the role is not
             able to be determined at the present time."
         REFERENCE
             "RFC3036, LDP Specification, Section 2.5.3.,
             Session Initialization"
         ::= { mplsLdpSessionEntry 3 }

     mplsLdpSessionProtocolVersion OBJECT-TYPE
         SYNTAX      Unsigned32(1..65535)
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The version of the LDP Protocol which
             this session is using.  This is the version of



RFC 3815                      MPLS LDP MIB                     June 2004


             the LDP protocol which has been negotiated
             during session initialization."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.3,
            Initialization Message."
         ::= { mplsLdpSessionEntry 4 }

     mplsLdpSessionKeepAliveHoldTimeRem OBJECT-TYPE
         SYNTAX      TimeInterval
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The keep alive hold time remaining for
             this session."
         ::= { mplsLdpSessionEntry 5 }

        mplsLdpSessionKeepAliveTime OBJECT-TYPE
            SYNTAX      Unsigned32 (1..65535)
            UNITS       "seconds"
            MAX-ACCESS  read-only
            STATUS      current
            DESCRIPTION
                "The negotiated KeepAlive Time which
                represents the amount of seconds between
                keep alive messages.  The
                mplsLdpEntityKeepAliveHoldTimer
                related to this Session is the
                value that was proposed as the
                KeepAlive Time for this session.

                This value is negotiated during
                session initialization between
                the entity's proposed value
                (i.e., the value configured in
                mplsLdpEntityKeepAliveHoldTimer)
                and the peer's proposed
                KeepAlive Hold Timer value.
                This value is the smaller
                of the two proposed values."
            REFERENCE
               "RFC3036, LDP Specification, Section 3.5.3,
               Initialization Message."
            ::= { mplsLdpSessionEntry 6 }

        mplsLdpSessionMaxPduLength OBJECT-TYPE
            SYNTAX      Unsigned32 (1..65535)
            UNITS       "octets"
            MAX-ACCESS  read-only



RFC 3815                      MPLS LDP MIB                     June 2004


            STATUS      current
            DESCRIPTION
                "The value of maximum allowable length for LDP PDUs for
                this session.  This value may have been negotiated
                during the Session Initialization.  This object is
                related to the mplsLdpEntityMaxPduLength object.  The
                mplsLdpEntityMaxPduLength object specifies the requested
                LDP PDU length, and this object reflects the negotiated
                LDP PDU length between the Entity and
                the Peer."
            REFERENCE
               "RFC3036, LDP Specification, Section 3.5.3,
               Initialization Message."
            ::= { mplsLdpSessionEntry 7 }

     mplsLdpSessionDiscontinuityTime OBJECT-TYPE
         SYNTAX      TimeStamp
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The value of sysUpTime on the most recent occasion
             at which any one or more of this session's counters
             suffered a discontinuity.  The relevant counters are
             the specific instances associated with this session
             of any Counter32 object contained in the
             mplsLdpSessionStatsTable.

             The initial value of this object is the value of
             sysUpTime when the entry was created in this table.

             Also, a command generator can distinguish when a session
             between a given Entity and Peer goes away and a new
             session is established.  This value would change and
             thus indicate to the command generator that this is a
             different session."
         ::= { mplsLdpSessionEntry 8 }

     --
     -- The MPLS LDP Session Statistics Table
     --

     mplsLdpSessionStatsTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsLdpSessionStatsEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "A table of statistics for Sessions between
             LDP Entities and LDP Peers.  This table AUGMENTS



RFC 3815                      MPLS LDP MIB                     June 2004


             the mplsLdpPeerTable."
         ::= { mplsLdpSessionObjects 4 }

     mplsLdpSessionStatsEntry OBJECT-TYPE
         SYNTAX      MplsLdpSessionStatsEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "An entry in this table represents statistical
             information on a single session between an LDP
             Entity and LDP Peer."

         AUGMENTS       { mplsLdpPeerEntry }
         ::= { mplsLdpSessionStatsTable 1 }

     MplsLdpSessionStatsEntry ::= SEQUENCE {
         mplsLdpSessionStatsUnknownMesTypeErrors  Counter32,
         mplsLdpSessionStatsUnknownTlvErrors      Counter32
     }

     mplsLdpSessionStatsUnknownMesTypeErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Unknown Message Type
             Errors detected by this LSR/LER during this session.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpSessionDiscontinuityTime."
         ::= { mplsLdpSessionStatsEntry 1 }

     mplsLdpSessionStatsUnknownTlvErrors OBJECT-TYPE
         SYNTAX      Counter32
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This object counts the number of Unknown TLV Errors
             detected by this LSR/LER during this session.

             Discontinuities in the value of this counter can occur
             at re-initialization of the management system, and at
             other times as indicated by the value of
             mplsLdpSessionDiscontinuityTime."
         ::= { mplsLdpSessionStatsEntry 2 }




RFC 3815                      MPLS LDP MIB                     June 2004


     --
     -- The MPLS LDP Hello Adjacency Table
     --

     mplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::=
                                   { mplsLdpSessionObjects 5 }

     mplsLdpHelloAdjacencyTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsLdpHelloAdjacencyEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "A table of Hello Adjacencies for Sessions."
         ::= { mplsLdpHelloAdjacencyObjects 1 }

     mplsLdpHelloAdjacencyEntry OBJECT-TYPE
         SYNTAX      MplsLdpHelloAdjacencyEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "Each row represents a single LDP Hello Adjacency.
             An LDP Session can have one or more Hello
             Adjacencies."
              INDEX       { mplsLdpEntityLdpId,
                            mplsLdpEntityIndex,
                            mplsLdpPeerLdpId,
                            mplsLdpHelloAdjacencyIndex }
         ::= { mplsLdpHelloAdjacencyTable 1 }

     MplsLdpHelloAdjacencyEntry ::= SEQUENCE {
         mplsLdpHelloAdjacencyIndex         Unsigned32,
         mplsLdpHelloAdjacencyHoldTimeRem   TimeInterval,
         mplsLdpHelloAdjacencyHoldTime      Unsigned32,
         mplsLdpHelloAdjacencyType          INTEGER
     }

     mplsLdpHelloAdjacencyIndex OBJECT-TYPE
         SYNTAX      Unsigned32 (1..4294967295)
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "An identifier for this specific adjacency."
         ::= { mplsLdpHelloAdjacencyEntry 1 }

     mplsLdpHelloAdjacencyHoldTimeRem OBJECT-TYPE
         SYNTAX      TimeInterval
         UNITS       "seconds"
         MAX-ACCESS  read-only



RFC 3815                      MPLS LDP MIB                     June 2004


         STATUS      current
         DESCRIPTION
             "If the value of this object is 65535,
             this means that the hold time is infinite
             (i.e., wait forever).

             Otherwise, the time remaining for
             this Hello Adjacency to receive its
             next Hello Message.

             This interval will change when the 'next'
             Hello Message which corresponds to this
             Hello Adjacency is received unless it
             is infinite."
         ::= { mplsLdpHelloAdjacencyEntry 2 }

     mplsLdpHelloAdjacencyHoldTime OBJECT-TYPE
         SYNTAX Unsigned32 (0..65535)
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The Hello hold time which is negotiated between
             the Entity and the Peer.  The entity associated
             with this Hello Adjacency issues a proposed
             Hello Hold Time value in the
             mplsLdpEntityHelloHoldTimer object.  The peer
             also proposes a value and this object represents
             the negotiated value.

             A value of 0 means the default,
             which is 15 seconds for Link Hellos
             and 45 seconds for Targeted Hellos.
             A value of 65535 indicates an
             infinite hold time."
         REFERENCE
            "RFC3036, LDP Specification, Section 3.5.2 Hello Message"
         ::= { mplsLdpHelloAdjacencyEntry 3 }

     mplsLdpHelloAdjacencyType OBJECT-TYPE
         SYNTAX      INTEGER {
                        link(1),
                        targeted(2)
                     }
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "This adjacency is the result of a 'link'
             hello if the value of this object is link(1).



RFC 3815                      MPLS LDP MIB                     June 2004


             Otherwise, it is a result of a 'targeted'
             hello, targeted(2)."
         ::= { mplsLdpHelloAdjacencyEntry 4 }

     --
     --  Session Label (LSP) Mapping to LSR MIB's
     --  In Segment LIB Information.
     --
     --
     -- NOTE: the next 2 tables map to the
     -- MPLS-LSR-STD-MIB's MplsInSegmentTable
     -- and MplsOutSegmentTable.  The
     -- cross-connect (XC) information is not
     -- represented here as it can be gleaned
     -- from the MPLS-LSR-STD-MIB.
     --

     mplsInSegmentLdpLspTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsInSegmentLdpLspEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "A table of LDP LSP's which
             map to the mplsInSegmentTable in the
             MPLS-LSR-STD-MIB module."
         ::= { mplsLdpSessionObjects 6 }

     mplsInSegmentLdpLspEntry OBJECT-TYPE
         SYNTAX      MplsInSegmentLdpLspEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "An entry in this table represents information
             on a single LDP LSP which is represented by
             a session's index triple (mplsLdpEntityLdpId,
             mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the
             index for the mplsInSegmentTable
             (mplsInSegmentLdpLspLabelIndex) from the
             MPLS-LSR-STD-MIB.

             The information contained in a row is read-only."
         INDEX       { mplsLdpEntityLdpId,
                       mplsLdpEntityIndex,
                       mplsLdpPeerLdpId,
                       mplsInSegmentLdpLspIndex
                     }
         ::= { mplsInSegmentLdpLspTable 1 }




RFC 3815                      MPLS LDP MIB                     June 2004


     MplsInSegmentLdpLspEntry ::= SEQUENCE {
         mplsInSegmentLdpLspIndex                 MplsIndexType,
         mplsInSegmentLdpLspLabelType             MplsLdpLabelType,
         mplsInSegmentLdpLspType                  MplsLspType
     }

     mplsInSegmentLdpLspIndex OBJECT-TYPE
         SYNTAX        MplsIndexType
         MAX-ACCESS    not-accessible
         STATUS        current
         DESCRIPTION
             "This contains the same value as the
             mplsInSegmentIndex in the
             MPLS-LSR-STD-MIB's mplsInSegmentTable."
         ::= { mplsInSegmentLdpLspEntry 1 }

     mplsInSegmentLdpLspLabelType  OBJECT-TYPE
         SYNTAX        MplsLdpLabelType
         MAX-ACCESS    read-only
         STATUS        current
         DESCRIPTION
             "The Layer 2 Label Type."
         ::= { mplsInSegmentLdpLspEntry 2 }

     mplsInSegmentLdpLspType OBJECT-TYPE
         SYNTAX        MplsLspType
         MAX-ACCESS    read-only
         STATUS        current
         DESCRIPTION
             "The type of LSP connection."
         ::= { mplsInSegmentLdpLspEntry 3 }

     --
     --  Session Label (LSP) Mapping to LSR MIB's
     --  Out Segment LIB Information.
     --

     mplsOutSegmentLdpLspTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsOutSegmentLdpLspEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "A table of LDP LSP's which
             map to the mplsOutSegmentTable in the
            MPLS-LSR-STD-MIB."
         ::= { mplsLdpSessionObjects 7 }

     mplsOutSegmentLdpLspEntry OBJECT-TYPE



RFC 3815                      MPLS LDP MIB                     June 2004


         SYNTAX      MplsOutSegmentLdpLspEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "An entry in this table represents information
             on a single LDP LSP which is represented by
             a session's index triple (mplsLdpEntityLdpId,
             mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the
             index (mplsOutSegmentLdpLspIndex)
             for the mplsOutSegmentTable.

             The information contained in a row is read-only."
         INDEX       { mplsLdpEntityLdpId,
                       mplsLdpEntityIndex,
                       mplsLdpPeerLdpId,
                       mplsOutSegmentLdpLspIndex
                     }
         ::= { mplsOutSegmentLdpLspTable 1 }

     MplsOutSegmentLdpLspEntry ::= SEQUENCE {
         mplsOutSegmentLdpLspIndex                 MplsIndexType,
         mplsOutSegmentLdpLspLabelType             MplsLdpLabelType,
         mplsOutSegmentLdpLspType                  MplsLspType
     }

     mplsOutSegmentLdpLspIndex OBJECT-TYPE
         SYNTAX       MplsIndexType
         MAX-ACCESS   not-accessible
         STATUS       current
         DESCRIPTION
             "This contains the same value as the
             mplsOutSegmentIndex in the
             MPLS-LSR-STD-MIB's mplsOutSegmentTable."
         ::= { mplsOutSegmentLdpLspEntry 1 }

     mplsOutSegmentLdpLspLabelType  OBJECT-TYPE
         SYNTAX        MplsLdpLabelType
         MAX-ACCESS    read-only
         STATUS        current
         DESCRIPTION
             "The Layer 2 Label Type."
         ::= { mplsOutSegmentLdpLspEntry 2 }

     mplsOutSegmentLdpLspType OBJECT-TYPE
         SYNTAX        MplsLspType
         MAX-ACCESS    read-only
         STATUS        current
         DESCRIPTION



RFC 3815                      MPLS LDP MIB                     June 2004


             "The type of LSP connection."
         ::= { mplsOutSegmentLdpLspEntry 3 }

     --
     -- Mpls FEC Table
     --

     mplsFecObjects OBJECT IDENTIFIER ::=
                                { mplsLdpSessionObjects 8 }

     mplsFecLastChange OBJECT-TYPE
         SYNTAX  TimeStamp
         MAX-ACCESS read-only
         STATUS current
         DESCRIPTION
             "The value of sysUpTime at the time of the most
             recent addition/deletion of an entry
             to/from the mplsLdpFectTable or
             the most recent change in values to any objects
             in the mplsLdpFecTable.

             If no such changes have occurred since the last
             re-initialization of the local management subsystem,
             then this object contains a zero value."
        ::= { mplsFecObjects 1 }

     mplsFecIndexNext  OBJECT-TYPE
         SYNTAX         IndexIntegerNextFree
         MAX-ACCESS     read-only
         STATUS         current
         DESCRIPTION
             "This object contains an appropriate value to
             be used for mplsFecIndex when creating
             entries in the mplsFecTable. The value
             0 indicates that no unassigned entries are
             available."
        ::= { mplsFecObjects 2 }

     mplsFecTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsFecEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "This table represents the FEC
             (Forwarding Equivalence Class)
             Information associated with an LSP."
         ::= { mplsFecObjects 3 }




RFC 3815                      MPLS LDP MIB                     June 2004


     mplsFecEntry OBJECT-TYPE
         SYNTAX      MplsFecEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "Each row represents a single FEC Element."
         INDEX       { mplsFecIndex }
         ::= { mplsFecTable 1 }

     MplsFecEntry ::= SEQUENCE {
         mplsFecIndex               IndexInteger,
         mplsFecType                INTEGER,
         mplsFecAddrType            InetAddressType,
         mplsFecAddr                InetAddress,
         mplsFecAddrPrefixLength    InetAddressPrefixLength,
         mplsFecStorageType         StorageType,
         mplsFecRowStatus           RowStatus
     }

     mplsFecIndex OBJECT-TYPE
         SYNTAX      IndexInteger
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "The index which uniquely identifies this entry."
         ::= { mplsFecEntry 1 }

     mplsFecType  OBJECT-TYPE
         SYNTAX      INTEGER {
                        prefix(1),
                        hostAddress(2)
                     }
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The type of the FEC.  If the value of this object
             is 'prefix(1)' then the FEC type described by this
             row is an address prefix.

             If the value of this object is 'hostAddress(2)' then
             the FEC type described by this row is a host address."
         REFERENCE
             "RFC3036, Section 3.4.1. FEC TLV."
         ::= { mplsFecEntry 2 }

     mplsFecAddrType  OBJECT-TYPE
         SYNTAX      InetAddressType
         MAX-ACCESS  read-create



RFC 3815                      MPLS LDP MIB                     June 2004


         STATUS      current
         DESCRIPTION
             "The value of this object is the type of the
             Internet address.  The value of this object,
             decides how the value of the mplsFecAddr object
             is interpreted."
         REFERENCE
             "RFC3036, Section 3.4.1. FEC TLV."
         ::= { mplsFecEntry 4 }

     mplsFecAddr     OBJECT-TYPE
         SYNTAX      InetAddress
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The value of this object is interpreted based
             on the value of the 'mplsFecAddrType' object.

             This address is then further interpretted as
             an being used with the address prefix,
             or as the host address.  This further interpretation
             is indicated by the 'mplsFecType' object.
             In other words, the FEC element is populated
             according to the Prefix FEC Element value encoding, or
             the Host Address FEC Element encoding."
         REFERENCE
             "RFC3036, Section 3.4.1 FEC TLV."
         ::= { mplsFecEntry 5 }

     mplsFecAddrPrefixLength  OBJECT-TYPE
         SYNTAX      InetAddressPrefixLength
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "If the value of the 'mplsFecType' is 'hostAddress(2)'
             then this object is undefined.

             If the value of 'mplsFecType' is 'prefix(1)'
             then the value of this object is the length in
             bits of the address prefix represented by
             'mplsFecAddr', or zero.  If the value of this
             object is zero, this indicates that the
             prefix matches all addresses.  In this case the
             address prefix MUST also be zero (i.e., 'mplsFecAddr'
             should have the value of zero.)"
         REFERENCE
             "RFC3036, Section 3.4.1. FEC TLV."
         DEFVAL { 0 }



RFC 3815                      MPLS LDP MIB                     June 2004


         ::= { mplsFecEntry 3 }

     mplsFecStorageType  OBJECT-TYPE
         SYNTAX      StorageType
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The storage type for this conceptual row.
             Conceptual rows having the value 'permanent(4)'
             need not allow write-access to any columnar
             objects in the row."
         DEFVAL { nonVolatile }
         ::= { mplsFecEntry 6 }

     mplsFecRowStatus OBJECT-TYPE
         SYNTAX      RowStatus
         MAX-ACCESS  read-create
         STATUS      current
         DESCRIPTION
             "The status of this conceptual row.  If the value of this
             object is 'active(1)', then none of the writable objects
             of this entry can be modified, except to set this object
             to 'destroy(6)'.

             NOTE: if this row is being referenced by any entry in
             the mplsLdpLspFecTable, then a request to destroy
             this row, will result in an inconsistentValue error."
         ::= { mplsFecEntry 7 }

     --
     --  LDP LSP FEC Table
     --

     mplsLdpLspFecLastChange OBJECT-TYPE
        SYNTAX TimeStamp
        MAX-ACCESS read-only
        STATUS current
        DESCRIPTION
             "The value of sysUpTime at the time of the most
             recent addition/deletion of an entry
             to/from the mplsLdpLspFecTable or
             the most recent change in values to any objects in the
             mplsLdpLspFecTable.

             If no such changes have occurred since the last
             re-initialization of the local management subsystem,
             then this object contains a zero value."
       ::= { mplsLdpSessionObjects 9 }



RFC 3815                      MPLS LDP MIB                     June 2004


     mplsLdpLspFecTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF MplsLdpLspFecEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
           "A table which shows the relationship between
           LDP LSPs and FECs.  Each row represents
           a single LDP LSP to FEC association."
       ::= { mplsLdpSessionObjects 10 }

     mplsLdpLspFecEntry OBJECT-TYPE
        SYNTAX     MplsLdpLspFecEntry
        MAX-ACCESS not-accessible
        STATUS     current
        DESCRIPTION
           "An entry represents a LDP LSP
           to FEC association."
        INDEX       { mplsLdpEntityLdpId,
                      mplsLdpEntityIndex,
                      mplsLdpPeerLdpId,
                      mplsLdpLspFecSegment,
                      mplsLdpLspFecSegmentIndex,
                      mplsLdpLspFecIndex
                     }
        ::= { mplsLdpLspFecTable 1 }

     MplsLdpLspFecEntry ::= SEQUENCE {
        mplsLdpLspFecSegment       INTEGER,
        mplsLdpLspFecSegmentIndex  MplsIndexType,
        mplsLdpLspFecIndex         IndexInteger,
        mplsLdpLspFecStorageType   StorageType,
        mplsLdpLspFecRowStatus     RowStatus
     }

     mplsLdpLspFecSegment OBJECT-TYPE
         SYNTAX INTEGER {
                            inSegment(1),
                            outSegment(2)
                        }
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
            "If the value is inSegment(1), then this
            indicates that the following index,
            mplsLdpLspFecSegmentIndex, contains the same
            value as the mplsInSegmentLdpLspIndex.

            Otherwise, if the value of this object is



RFC 3815                      MPLS LDP MIB                     June 2004


            outSegment(2),  then this
            indicates that following index,
            mplsLdpLspFecSegmentIndex, contains the same
            value as the mplsOutSegmentLdpLspIndex."
         ::= { mplsLdpLspFecEntry 1 }

     mplsLdpLspFecSegmentIndex OBJECT-TYPE
         SYNTAX      MplsIndexType
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
            "This index is interpretted by using the value
            of the mplsLdpLspFecSegment.

            If the mplsLdpLspFecSegment is inSegment(1),
            then this index has the same value as
            mplsInSegmentLdpLspIndex.

            If the mplsLdpLspFecSegment is outSegment(2),
            then this index has the same value as
            mplsOutSegmentLdpLspIndex."
         ::= { mplsLdpLspFecEntry 2 }

     mplsLdpLspFecIndex   OBJECT-TYPE
         SYNTAX      IndexInteger
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "This index identifies the FEC entry in the
             mplsFecTable associated with this session.
             In other words, the value of this index
             is the same as the value of the mplsFecIndex
             that denotes the FEC associated with this
             Session."
         ::= { mplsLdpLspFecEntry 3 }

     mplsLdpLspFecStorageType  OBJECT-TYPE
        SYNTAX      StorageType
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The storage type for this conceptual row.
            Conceptual rows having the value 'permanent(4)'
            need not allow write-access to any columnar
            objects in the row."
        DEFVAL { nonVolatile }
        ::= { mplsLdpLspFecEntry 4 }




RFC 3815                      MPLS LDP MIB                     June 2004


     mplsLdpLspFecRowStatus  OBJECT-TYPE
        SYNTAX     RowStatus
        MAX-ACCESS read-create
        STATUS     current
        DESCRIPTION
            "The status of this conceptual row.  If the
             value of this object is 'active(1)', then
             none of the writable objects of this entry
             can be modified.

             The Agent should delete this row when
             the session ceases to exist.  If an
             operator wants to associate the session with
             a different FEC, the recommended
             procedure is (as described in detail in the section
             entitled, 'Changing Values After Session
             Establishment', and again described in the
             DESCRIPTION clause of the
             mplsLdpEntityAdminStatus object)
             is to set the mplsLdpEntityAdminStatus to
             down, thereby explicitly causing a session
             to be torn down. This will also
             cause this entry to be deleted.

             Then, set the mplsLdpEntityAdminStatus
             to enable which enables a new session to be initiated.
             Once the session is initiated, an entry may be
             added to this table to associate the new session
             with a FEC."
        ::= { mplsLdpLspFecEntry 5 }

     --
     -- Address Message/Address Withdraw Message Information
     --
     -- This information is associated with a specific Session
     -- because Label Address Messages are sent after session
     -- initialization has taken place.
     --

     mplsLdpSessionPeerAddrTable OBJECT-TYPE
         SYNTAX      SEQUENCE OF MplsLdpSessionPeerAddrEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "This table 'extends' the mplsLdpSessionTable.
             This table is used to store Label Address Information
             from Label Address Messages received by this LSR from
             Peers.  This table is read-only and should be updated



RFC 3815                      MPLS LDP MIB                     June 2004


             when Label Withdraw Address Messages are received, i.e.,
             Rows should be deleted as appropriate.

             NOTE:  since more than one address may be contained
             in a Label Address Message, this table 'sparse augments',
             the mplsLdpSessionTable's information."
         ::= { mplsLdpSessionObjects 11 }

     mplsLdpSessionPeerAddrEntry OBJECT-TYPE
         SYNTAX      MplsLdpSessionPeerAddrEntry
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "An entry in this table represents information on
             a session's single next hop address which was
             advertised in an Address Message from the LDP peer.
             The information contained in a row is read-only."
         INDEX       { mplsLdpEntityLdpId,
                       mplsLdpEntityIndex,
                       mplsLdpPeerLdpId,
                       mplsLdpSessionPeerAddrIndex
                     }
         ::= { mplsLdpSessionPeerAddrTable 1 }

     MplsLdpSessionPeerAddrEntry ::= SEQUENCE {
         mplsLdpSessionPeerAddrIndex       Unsigned32,
         mplsLdpSessionPeerNextHopAddrType InetAddressType,
         mplsLdpSessionPeerNextHopAddr     InetAddress
     }

     mplsLdpSessionPeerAddrIndex OBJECT-TYPE
         SYNTAX      Unsigned32 (1..4294967295)
         MAX-ACCESS  not-accessible
         STATUS      current
         DESCRIPTION
             "An index which uniquely identifies this entry within
             a given session."
         ::= { mplsLdpSessionPeerAddrEntry 1 }

     mplsLdpSessionPeerNextHopAddrType OBJECT-TYPE
         SYNTAX      InetAddressType
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The internetwork layer address type of this Next Hop
             Address as specified in the Label Address Message
             associated with this Session. The value of this
             object indicates how to interpret the value of



RFC 3815                      MPLS LDP MIB                     June 2004


             mplsLdpSessionPeerNextHopAddr."
         ::= { mplsLdpSessionPeerAddrEntry 2 }

     mplsLdpSessionPeerNextHopAddr OBJECT-TYPE
         SYNTAX      InetAddress
         MAX-ACCESS  read-only
         STATUS      current
         DESCRIPTION
             "The next hop address.  The type of this address
             is specified by the value of the
             mplsLdpSessionPeerNextHopAddrType."
         REFERENCE
             "RFC3036, Section 2.7. LDP Identifiers
             and Next Hop Addresses"
            ::= { mplsLdpSessionPeerAddrEntry 3 }

     ---
     --- Notifications
     ---

     mplsLdpInitSessionThresholdExceeded NOTIFICATION-TYPE
          OBJECTS     {
                        mplsLdpEntityInitSessionThreshold
                      }
          STATUS      current
          DESCRIPTION
             "This notification is generated when the value of
             the 'mplsLdpEntityInitSessionThreshold' object
             is not zero, and the number of Session
             Initialization messages exceeds the value
             of the 'mplsLdpEntityInitSessionThreshold' object."
          ::= { mplsLdpNotifications 1 }

     mplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE
          OBJECTS     {
                        mplsLdpEntityPathVectorLimit,
                        mplsLdpPeerPathVectorLimit
                      }
          STATUS      current
          DESCRIPTION
             "This notification is sent when the
             'mplsLdpEntityPathVectorLimit' does NOT match
             the value of the 'mplsLdpPeerPathVectorLimit' for
             a specific Entity."
          REFERENCE
             "RFC3036, LDP Specification, Section 3.5.3."
          ::= { mplsLdpNotifications 2 }




RFC 3815                      MPLS LDP MIB                     June 2004


     mplsLdpSessionUp NOTIFICATION-TYPE
          OBJECTS     {
                         mplsLdpSessionState,
                         mplsLdpSessionDiscontinuityTime,
                         mplsLdpSessionStatsUnknownMesTypeErrors,
                         mplsLdpSessionStatsUnknownTlvErrors
                      }
          STATUS      current
          DESCRIPTION
             "If this notification is sent when the
             value of 'mplsLdpSessionState' enters
             the 'operational(5)' state."
          ::= { mplsLdpNotifications 3 }

     mplsLdpSessionDown NOTIFICATION-TYPE
          OBJECTS     {
                         mplsLdpSessionState,
                         mplsLdpSessionDiscontinuityTime,
                         mplsLdpSessionStatsUnknownMesTypeErrors,
                         mplsLdpSessionStatsUnknownTlvErrors

                      }
          STATUS      current
          DESCRIPTION
             "This notification is sent when the
             value of 'mplsLdpSessionState' leaves
             the 'operational(5)' state."
          ::= { mplsLdpNotifications 4 }

     --****************************************************************
     -- Module Conformance Statement
     --****************************************************************

     mplsLdpGroups
         OBJECT IDENTIFIER ::= { mplsLdpConformance 1 }

     mplsLdpCompliances
         OBJECT IDENTIFIER ::= { mplsLdpConformance 2 }

     --
     -- Full Compliance
     --

     mplsLdpModuleFullCompliance MODULE-COMPLIANCE
         STATUS current
         DESCRIPTION
             "The Module is implemented with support
             for read-create and read-write.  In other



RFC 3815                      MPLS LDP MIB                     June 2004


             words, both monitoring and configuration
             are available when using this MODULE-COMPLIANCE."

         MODULE -- this module
             MANDATORY-GROUPS    { mplsLdpGeneralGroup,
                                   mplsLdpNotificationsGroup
                                 }
         GROUP mplsLdpLspGroup
         DESCRIPTION
             "This group must be supported if the LSR MIB is
             implemented, specifically the mplsInSegmentTable,
             the mplsOutSegmentTable or the mplsXCTable."

         OBJECT mplsLdpEntityTargetPeerAddrType
         SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
         DESCRIPTION
            "An implementation is only required to support
            'unknown(0)', IPv4 and globally unique IPv6 addresses."

         OBJECT mplsLdpEntityTargetPeerAddr
         SYNTAX InetAddress (SIZE(0|4|16))
         DESCRIPTION
             "An implementation is only required to support IPv4 and
             globally unique IPv6 addresses."

         OBJECT mplsLdpEntityRowStatus
         SYNTAX RowStatus { active(1) }
         WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
         DESCRIPTION
             "Support for createAndWait and notInService is not
             required."

         OBJECT mplsFecAddrType
         SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
         DESCRIPTION
            "An implementation is only required to support
            'unknown(0)', IPv4 and globally unique IPv6 addresses."

         OBJECT mplsFecAddr
         SYNTAX InetAddress (SIZE(0|4|16))
         DESCRIPTION
             "An implementation is only required to support IPv4 and
             globally unique IPv6 addresses."

         OBJECT mplsFecRowStatus
         SYNTAX RowStatus { active(1) }
         WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
         DESCRIPTION



RFC 3815                      MPLS LDP MIB                     June 2004


             "Support for createAndWait and notInService is not
             required."

         OBJECT mplsLdpLspFecRowStatus
         SYNTAX RowStatus { active(1) }
         WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
         DESCRIPTION
             "Support for createAndWait and notInService is not
             required."

         OBJECT mplsLdpSessionPeerNextHopAddrType
         SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
         DESCRIPTION
             "An implementation is only required to support
             'unknown(0)', IPv4 and globally unique IPv6 addresses."

         OBJECT mplsLdpSessionPeerNextHopAddr
         SYNTAX InetAddress (SIZE(0|4|16))
         DESCRIPTION
             "An implementation is only required to support IPv4
             and globally unique IPv6 addresses."

         ::= { mplsLdpCompliances 1 }

     --
     -- Read-Only Compliance
     --

     mplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE
         STATUS current
         DESCRIPTION
             "The Module is implemented with support
             for read-only.  In other words, only monitoring
             is available by implementing this MODULE-COMPLIANCE."

         MODULE -- this module
             MANDATORY-GROUPS    { mplsLdpGeneralGroup,
                                   mplsLdpNotificationsGroup
                                 }

         GROUP mplsLdpLspGroup
         DESCRIPTION
             "This group must be supported if the LSR MIB is
             implemented, specifically the mplsInSegmentTable,
             the mplsOutSegmentTable or the mplsXCTable."

         OBJECT       mplsLdpEntityProtocolVersion
         MIN-ACCESS   read-only



RFC 3815                      MPLS LDP MIB                     June 2004


         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityAdminStatus
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityTcpPort
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityUdpDscPort
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityMaxPduLength
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityKeepAliveHoldTimer
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityHelloHoldTimer
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityInitSessionThreshold
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityLabelDistMethod
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityLabelRetentionMode
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."




RFC 3815                      MPLS LDP MIB                     June 2004


         OBJECT       mplsLdpEntityPathVectorLimit
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityHopCountLimit
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityTransportAddrKind
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityTargetPeer
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityTargetPeerAddrType
         SYNTAX       InetAddressType { unknown(0), ipv4(1), ipv6(2) }
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required.
            An implementation is only required to support
            'unknown(0)', IPv4 and globally unique IPv6 addresses."

         OBJECT       mplsLdpEntityTargetPeerAddr
         SYNTAX       InetAddress (SIZE(0|4|16))
         MIN-ACCESS   read-only
         DESCRIPTION
             "Write access is not required.
             An implementation is only required to support IPv4 and
             globally unique IPv6 addresses."

         OBJECT       mplsLdpEntityLabelType
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsLdpEntityStorageType
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT mplsLdpEntityRowStatus
         SYNTAX RowStatus { active(1) }



RFC 3815                      MPLS LDP MIB                     June 2004


         MIN-ACCESS   read-only
         DESCRIPTION
             "Write access is not required, and active is the
             only status that needs to be supported."

         OBJECT       mplsFecType
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsFecAddrPrefixLength
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT       mplsFecAddrType
         SYNTAX       InetAddressType { unknown(0), ipv4(1), ipv6(2) }
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required.
            An implementation is only required to support
            'unknown(0)', IPv4 and globally unique IPv6 addresses."

         OBJECT        mplsFecAddr
         SYNTAX        InetAddress (SIZE(0|4|16))
         MIN-ACCESS    read-only
         DESCRIPTION
             "Write access is not required.
             An implementation is only required to support IPv4 and
             globally unique IPv6 addresses."

         OBJECT       mplsFecStorageType
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."

         OBJECT mplsFecRowStatus
         SYNTAX RowStatus { active(1) }
         MIN-ACCESS   read-only
         DESCRIPTION
             "Write access is not required, and active is the
             only status that needs to be supported."

         OBJECT       mplsLdpLspFecStorageType
         MIN-ACCESS   read-only
         DESCRIPTION
            "Write access is not required."




RFC 3815                      MPLS LDP MIB                     June 2004


         OBJECT mplsLdpLspFecRowStatus
         SYNTAX RowStatus { active(1) }
         MIN-ACCESS   read-only
         DESCRIPTION
             "Write access is not required, and active is the
             only status that needs to be supported."

         OBJECT mplsLdpSessionPeerNextHopAddrType
         SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
         DESCRIPTION
            "An implementation is only required to support
            'unknown(0)', IPv4 and globally unique IPv6 addresses."


         OBJECT mplsLdpSessionPeerNextHopAddr
         SYNTAX InetAddress (SIZE(0|4|16))
         DESCRIPTION
             "An implementation is only required to support IPv4
             and globally unique IPv6 addresses."

         ::= { mplsLdpCompliances 2 }

     -- units of conformance

     mplsLdpGeneralGroup OBJECT-GROUP
         OBJECTS {
         mplsLdpLsrId,
         mplsLdpLsrLoopDetectionCapable,
         mplsLdpEntityLastChange,
         mplsLdpEntityIndexNext,
         mplsLdpEntityProtocolVersion,
         mplsLdpEntityAdminStatus,
         mplsLdpEntityOperStatus,
         mplsLdpEntityTcpPort,
         mplsLdpEntityUdpDscPort,
         mplsLdpEntityMaxPduLength,
         mplsLdpEntityKeepAliveHoldTimer,
         mplsLdpEntityHelloHoldTimer,
         mplsLdpEntityInitSessionThreshold,
         mplsLdpEntityLabelDistMethod,
         mplsLdpEntityLabelRetentionMode,
         mplsLdpEntityPathVectorLimit,
         mplsLdpEntityHopCountLimit,
         mplsLdpEntityTransportAddrKind,
         mplsLdpEntityTargetPeer,
         mplsLdpEntityTargetPeerAddrType,
         mplsLdpEntityTargetPeerAddr,
         mplsLdpEntityLabelType,



RFC 3815                      MPLS LDP MIB                     June 2004


         mplsLdpEntityDiscontinuityTime,
         mplsLdpEntityStorageType,
         mplsLdpEntityRowStatus,
         mplsLdpEntityStatsSessionAttempts,
         mplsLdpEntityStatsSessionRejectedNoHelloErrors,
         mplsLdpEntityStatsSessionRejectedAdErrors,
         mplsLdpEntityStatsSessionRejectedMaxPduErrors,
         mplsLdpEntityStatsSessionRejectedLRErrors,
         mplsLdpEntityStatsBadLdpIdentifierErrors,
         mplsLdpEntityStatsBadPduLengthErrors,
         mplsLdpEntityStatsBadMessageLengthErrors,
         mplsLdpEntityStatsBadTlvLengthErrors,
         mplsLdpEntityStatsMalformedTlvValueErrors,
         mplsLdpEntityStatsKeepAliveTimerExpErrors,
         mplsLdpEntityStatsShutdownReceivedNotifications,
         mplsLdpEntityStatsShutdownSentNotifications,
         mplsLdpPeerLastChange,
         mplsLdpPeerLabelDistMethod,
         mplsLdpPeerPathVectorLimit,
         mplsLdpPeerTransportAddrType,
         mplsLdpPeerTransportAddr,
         mplsLdpHelloAdjacencyHoldTimeRem,
         mplsLdpHelloAdjacencyHoldTime,
         mplsLdpHelloAdjacencyType,
         mplsLdpSessionStateLastChange,
         mplsLdpSessionState,
         mplsLdpSessionRole,
         mplsLdpSessionProtocolVersion,
         mplsLdpSessionKeepAliveHoldTimeRem,
         mplsLdpSessionKeepAliveTime,
         mplsLdpSessionMaxPduLength,
         mplsLdpSessionDiscontinuityTime,
         mplsLdpSessionStatsUnknownMesTypeErrors,
         mplsLdpSessionStatsUnknownTlvErrors,
         mplsLdpSessionPeerNextHopAddrType,
         mplsLdpSessionPeerNextHopAddr,
         mplsFecLastChange,
         mplsFecIndexNext,
         mplsFecType,
         mplsFecAddrType,
         mplsFecAddr,
         mplsFecAddrPrefixLength,
         mplsFecStorageType,
         mplsFecRowStatus
         }
         STATUS    current
         DESCRIPTION
             "Objects that apply to all MPLS LDP implementations."



RFC 3815                      MPLS LDP MIB                     June 2004


         ::= { mplsLdpGroups 1 }

     mplsLdpLspGroup OBJECT-GROUP
         OBJECTS {
         mplsInSegmentLdpLspLabelType,
         mplsInSegmentLdpLspType,
         mplsOutSegmentLdpLspLabelType,
         mplsOutSegmentLdpLspType,
         mplsLdpLspFecLastChange,
         mplsLdpLspFecStorageType,
         mplsLdpLspFecRowStatus
         }
         STATUS    current
         DESCRIPTION
             "These objects are for LDP implementations
             which interface to the Label Information Base (LIB)
             in the MPLS-LSR-STD-MIB.  The LIB is
             represented in the mplsInSegmentTable,
             mplsOutSegmentTable and mplsXCTable."
         ::= { mplsLdpGroups 2 }

     mplsLdpNotificationsGroup NOTIFICATION-GROUP
         NOTIFICATIONS { mplsLdpInitSessionThresholdExceeded,
                         mplsLdpPathVectorLimitMismatch,
                         mplsLdpSessionUp,
                         mplsLdpSessionDown
                            }
         STATUS   current
         DESCRIPTION
             "The notification for an MPLS LDP implementation."
         ::= { mplsLdpGroups 3 }

     END

4.1.  The MPLS-LDP-ATM-STD-MIB Module

   This MIB Module MUST be supported if LDP uses ATM as the Layer 2
   medium.  There are three tables in this MIB Module.  Two tables are
   for configuring LDP to use ATM.  These tables are the
   mplsLdpEntityAtmTable and the mplsLdpEntityAtmLRTable.  The third
   table is the mplsLdpAtmSessionTable which is a read-only table.  This
   MIB Module IMPORTS the AtmVpIdentifier TEXTUAL-CONVENTION from
   [RFC2514].








RFC 3815                      MPLS LDP MIB                     June 2004


4.1.1.  The LDP Entity ATM Table

   The mplsLdpEntityAtmTable provides a way to configure information
   which would be contained in the "Optional Parameter" portion of an
   LDP PDU Initialization Message.

4.1.2.  The LDP Entity ATM Label Range Table

   The mplsLdpEntityAtmLRTable provides a way to configure information
   which would be contained in the "ATM Label Range Components" portion
   of an LDP PDU Intialization Message, see  [RFC3035] and [RFC3036].

4.1.3.  The LDP ATM Session Table

   The MPLS LDP ATM Session Table is a read-only table which contains
   session information specific to ATM.

   MPLS-LDP-ATM-STD-MIB DEFINITIONS ::= BEGIN

   IMPORTS
       OBJECT-TYPE, MODULE-IDENTITY,
       Unsigned32
           FROM SNMPv2-SMI                                 --  [RFC2578]
       MODULE-COMPLIANCE, OBJECT-GROUP
           FROM SNMPv2-CONF                                --  [RFC2580]
       RowStatus,
       StorageType
           FROM SNMPv2-TC                                  --  [RFC2579]

       InterfaceIndexOrZero
           FROM IF-MIB                                     --  [RFC2020]

       AtmVpIdentifier
           FROM ATM-TC-MIB                                 --  [RFC2514]

       mplsStdMIB,
       MplsAtmVcIdentifier
           FROM MPLS-TC-STD-MIB                            --  [RFC3811]

       mplsLdpEntityLdpId,
       mplsLdpEntityIndex,
       mplsLdpPeerLdpId
           FROM MPLS-LDP-STD-MIB                           --  [RFC3813]

       ;

   mplsLdpAtmStdMIB MODULE-IDENTITY
       LAST-UPDATED "200406030000Z"  -- June 3, 2004



RFC 3815                      MPLS LDP MIB                     June 2004


       ORGANIZATION "Multiprotocol Label Switching (mpls)
                     Working Group"
       CONTACT-INFO
           "Joan Cucchiara (jcucchiara@mindspring.com)
            Marconi Communications, Inc.

            Hans Sjostrand (hans@ipunplugged.com)
            ipUnplugged

            James V. Luciani (james_luciani@mindspring.com)
            Marconi Communications, Inc.

            Working Group Chairs:
            George Swallow,   email: swallow@cisco.com
            Loa Andersson,    email: loa@pi.se

            MPLS Working Group, email: mpls@uu.net
       "
       DESCRIPTION
           "Copyright (C) The Internet Society (2004). The
           initial version of this MIB module was published
           in RFC 3815. For full legal notices see the RFC
           itself or see:
           http://www.ietf.org/copyrights/ianamib.html

           This MIB contains managed object definitions for
           configuring and monitoring the Multiprotocol Label
           Switching (MPLS), Label Distribution Protocol (LDP),
           utilizing Asynchronous Transfer Mode (ATM) as the Layer 2
           media."
       REVISION "200406030000Z"  -- June 3, 2004
       DESCRIPTION
           "Initial version published as part of RFC 3815."

       ::= { mplsStdMIB 5 }

   --****************************************************************

   mplsLdpAtmObjects       OBJECT IDENTIFIER
                               ::= { mplsLdpAtmStdMIB 1 }
   mplsLdpAtmConformance   OBJECT IDENTIFIER
                               ::= { mplsLdpAtmStdMIB 2 }

   --****************************************************************
   -- MPLS LDP ATM Objects
   --****************************************************************
   --
   -- Ldp Entity Objects for ATM



RFC 3815                      MPLS LDP MIB                     June 2004


   --

   mplsLdpEntityAtmObjects  OBJECT IDENTIFIER ::=
                                 { mplsLdpAtmObjects 1 }

   mplsLdpEntityAtmTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF MplsLdpEntityAtmEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table contains ATM specific information
           which could be used in the
           'Optional Parameters' and other ATM specific
           information.

           This table 'sparse augments' the mplsLdpEntityTable
           when ATM is the Layer 2 medium."
       ::= { mplsLdpEntityAtmObjects 1 }

   mplsLdpEntityAtmEntry OBJECT-TYPE
       SYNTAX      MplsLdpEntityAtmEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry in this table represents the ATM parameters
           and ATM information for this LDP entity."
       INDEX       {  mplsLdpEntityLdpId,
                      mplsLdpEntityIndex
                   }
       ::= { mplsLdpEntityAtmTable 1 }


   MplsLdpEntityAtmEntry ::= SEQUENCE {
       mplsLdpEntityAtmIfIndexOrZero        InterfaceIndexOrZero,
       mplsLdpEntityAtmMergeCap             INTEGER,
       mplsLdpEntityAtmLRComponents         Unsigned32,
       mplsLdpEntityAtmVcDirectionality     INTEGER,
       mplsLdpEntityAtmLsrConnectivity      INTEGER,
       mplsLdpEntityAtmDefaultControlVpi    AtmVpIdentifier,
       mplsLdpEntityAtmDefaultControlVci    MplsAtmVcIdentifier,
       mplsLdpEntityAtmUnlabTrafVpi         AtmVpIdentifier,
       mplsLdpEntityAtmUnlabTrafVci         MplsAtmVcIdentifier,
       mplsLdpEntityAtmStorageType          StorageType,
       mplsLdpEntityAtmRowStatus            RowStatus
   }

   mplsLdpEntityAtmIfIndexOrZero  OBJECT-TYPE
       SYNTAX      InterfaceIndexOrZero



RFC 3815                      MPLS LDP MIB                     June 2004


       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
          "This value represents either the InterfaceIndex
          or 0 (zero).  The value of zero means that the
          InterfaceIndex is not known.

          However, if the InterfaceIndex is known, then it must
          be represented by this value.

          If an InterfaceIndex becomes known, then the
          network management entity (e.g., SNMP agent) responsible
          for this object MUST change the value from 0 (zero) to the
          value of the InterfaceIndex.  If an ATM Label is
          being used in forwarding data, then the value of this
          object MUST be the InterfaceIndex."
       ::= { mplsLdpEntityAtmEntry 1 }

   mplsLdpEntityAtmMergeCap OBJECT-TYPE
       SYNTAX      INTEGER {
                       notSupported(0),
                       vpMerge(1),
                       vcMerge(2),
                       vpAndVcMerge(3)
                   }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "Denotes the Merge Capability of this Entity.
           This is the EXACT value for the ATM Session
           Parameter, field M (for ATM Merge Capabilities).
           The ATM Session Parameter is an optional
           parameter in the Initialization Message.

           The description from rfc3036.txt is:

           'M, ATM Merge Capabilities
              Specifies the merge capabilities of an ATM switch.  The
              following values are supported in this version of the
              specification:

                     Value          Meaning

                       0            Merge not supported
                       1            VP Merge supported
                       2            VC Merge supported
                       3            VP & VC Merge supported




RFC 3815                      MPLS LDP MIB                     June 2004


              If the merge capabilities of the LSRs differ, then:
              -  Non-merge and VC-merge LSRs may freely interoperate.

              -  The interoperability of VP-merge-capable switches
                 with non-VP-merge-capable switches is a subject
                 for future study.  When the LSRs differ on the
                 use of VP-merge, the session is established,
                 but VP merge is not used.'

              Please refer to the following reference for a
              complete description of this feature."

        REFERENCE
           "RFC3036, LDP Specification, Section 3.5.3
           Initialization Message."
       ::= { mplsLdpEntityAtmEntry 2 }

   mplsLdpEntityAtmLRComponents OBJECT-TYPE
       SYNTAX      Unsigned32 (1..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "Number of Label Range Components in the Initialization
           message.  This also represents the number of entries
           in the mplsLdpEntityAtmLRTable which correspond
           to this entry.

           This is the EXACT value for the ATM Session Parameter,
           field N (for Number of label range components).
           The ATM Session Parameter is an optional parameter
           in the Initialization Message.

           The description from rfc3036.txt is:

           'N, Number of label range components
              Specifies the number of ATM Label Range
              Components included in the TLV.'

            Please refer to the following reference for
            a complete description of this feature."
        REFERENCE
           "RFC3036, LDP Specification, Section 3.5.3
           Initialization Message."
       ::= { mplsLdpEntityAtmEntry 3 }

   mplsLdpEntityAtmVcDirectionality OBJECT-TYPE
       SYNTAX      INTEGER {
                              bidirectional(0),



RFC 3815                      MPLS LDP MIB                     June 2004


                              unidirectional(1)
                           }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "If the value of this object is 'bidirectional(0)',
           a given VCI, within a given VPI, is used as a
           label for both directions independently.

           If the value of this object is 'unidirectional(1)',
           a given VCI within a VPI designates one direction.

           This is the EXACT value for the ATM Session Parameter,
           field D (for VC Directionality).  The ATM Session
           Parameter is an optional parameter in the
           Initialization Message.

           The description from rfc3036.txt is:

           'D, VC Directionality
              A value of 0 specifies bidirectional VC capability,
              meaning the LSR can (within a given VPI) support
              the use of a given VCI as a label for both link
              directions independently.  A value of 1
              specifies unidirectional VC capability, meaning
              (within a given VPI) a given VCI may appear in
              a label mapping for one direction on the link
              only.  When either or both of the peers
              specifies unidirectional VC capability, both
              LSRs use unidirectional VC label assignment for
              the link as follows.  The LSRs compare their
              LDP Identifiers as unsigned integers.  The LSR
              with the larger LDP Identifier may assign
              only odd-numbered VCIs in the VPI/VCI
              range as labels.  The system with the smaller
              LDP Identifier may assign only even-numbered
              VCIs in the VPI/VCI range as labels.'

              Please refer to the following reference
              for a complete description of this feature."
        REFERENCE
           "RFC3036, LDP Specification, Section 3.5.3
           Initialization Message."
       ::= { mplsLdpEntityAtmEntry 4 }

   mplsLdpEntityAtmLsrConnectivity OBJECT-TYPE
       SYNTAX      INTEGER {
                      direct(1),



RFC 3815                      MPLS LDP MIB                     June 2004


                      indirect(2)
                   }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The peer LSR may be connected indirectly by means
           of an ATM VP so that the VPI values may be different
           on either endpoint so the label MUST be encoded
           entirely within the VCI field."
       DEFVAL { direct }
       ::= { mplsLdpEntityAtmEntry 5 }

   mplsLdpEntityAtmDefaultControlVpi OBJECT-TYPE
       SYNTAX      AtmVpIdentifier
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The default VPI value for the non-MPLS connection.  The
           default value of this is 0 (zero) but other values may
           be configured.  This object allows a different value
           to be configured."
       DEFVAL { 0 }
       ::= { mplsLdpEntityAtmEntry 6 }

   mplsLdpEntityAtmDefaultControlVci OBJECT-TYPE
       SYNTAX      MplsAtmVcIdentifier
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The Default VCI value for a non-MPLS connection.  The
           default value of this is 32 but other values may be
           configured.  This object allows a different value to
           be configured."
       DEFVAL { 32 }
       ::= { mplsLdpEntityAtmEntry 7 }

   mplsLdpEntityAtmUnlabTrafVpi OBJECT-TYPE
       SYNTAX      AtmVpIdentifier
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "VPI value of the VCC supporting unlabeled traffic.  This
           non-MPLS connection is used to carry unlabeled (IP)
           packets.  The default value is the same as the default
           value of the 'mplsLdpEntityAtmDefaultControlVpi', however
           another value may be configured."
       DEFVAL  { 0 }
       ::= { mplsLdpEntityAtmEntry 8 }



RFC 3815                      MPLS LDP MIB                     June 2004


   mplsLdpEntityAtmUnlabTrafVci OBJECT-TYPE
       SYNTAX      MplsAtmVcIdentifier
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "VCI value of the VCC supporting unlabeled traffic.
           This non-MPLS connection is used to carry unlabeled (IP)
           packets. The default value is the same as the default
           value of the 'mplsLdpEntityAtmDefaultControlVci', however
           another value may be configured."
       DEFVAL  { 32 }
       ::= { mplsLdpEntityAtmEntry 9 }

   mplsLdpEntityAtmStorageType  OBJECT-TYPE
       SYNTAX      StorageType
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The storage type for this conceptual row.
           Conceptual rows having the value 'permanent(4)'
           need not allow write-access to any columnar
           objects in the row."
       DEFVAL { nonVolatile }
       ::= { mplsLdpEntityAtmEntry 10 }

   mplsLdpEntityAtmRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The status of this conceptual row.  All writable
            objects in this row may be modified at any time,
            however, as described in detail in the section
            entitled, 'Changing Values After Session
            Establishment', and again described in the
            DESCRIPTION clause of the mplsLdpEntityAdminStatus
            object, if a session has been initiated with a Peer,
            changing objects in this table will wreak havoc
            with the session and interrupt traffic.  To repeat again:
            the recommended procedure is to set the
            mplsLdpEntityAdminStatus to down, thereby explicitly
            causing a session to be torn down. Then,
            change objects in this entry, then set the
            mplsLdpEntityAdminStatus to enable
            which enables a new session to be initiated."
       ::= { mplsLdpEntityAtmEntry 11 }

   --



RFC 3815                      MPLS LDP MIB                     June 2004


   -- The MPLS LDP Entity ATM Label Range Table
   --

   mplsLdpEntityAtmLRTable OBJECT-TYPE
       SYNTAX SEQUENCE OF MplsLdpEntityAtmLREntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "The MPLS LDP Entity ATM Label Range (LR) Table.
           The purpose of this table is to provide a mechanism
           for configuring a contiguous range of vpi's
           with a contiguous range of vci's, or a 'label range'
           for LDP Entities.

           LDP Entities which use ATM must have at least one
           entry in this table.

           There must exist at least one entry in this
           table for every LDP Entity that has
           'mplsLdpEntityOptionalParameters' object with
           a value of 'atmSessionParameters'."
       ::= { mplsLdpEntityAtmObjects 2 }

   mplsLdpEntityAtmLREntry OBJECT-TYPE
       SYNTAX MplsLdpEntityAtmLREntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "A row in the LDP Entity ATM Label
           Range Table.  One entry in this table contains
           information on a single range of labels
           represented by the configured Upper and Lower
           Bounds VPI/VCI pairs.  These are the same
           data used in the Initialization Message.

           NOTE:  The ranges for a specific LDP Entity
           are UNIQUE and non-overlapping.  For example,
           for a specific LDP Entity index, there could
           be one entry having LowerBound vpi/vci == 0/32, and
           UpperBound vpi/vci == 0/100, and a second entry
           for this same interface with LowerBound
           vpi/vci == 0/101 and UpperBound vpi/vci == 0/200.
           However, there could not be a third entry with
           LowerBound vpi/vci == 0/200 and
           UpperBound vpi/vci == 0/300 because this label
           range overlaps with the second entry (i.e., both
           entries now have 0/200).




RFC 3815                      MPLS LDP MIB                     June 2004


           A row will not become active unless a unique and
           non-overlapping range is specified.

           At least one label range entry for a
           specific LDP Entity MUST
           include the default VPI/VCI  values denoted
           in the LDP Entity Table.

           A request to create a row with an overlapping
           range should result in an inconsistentValue
           error."
       INDEX       {  mplsLdpEntityLdpId,
                      mplsLdpEntityIndex,
                      mplsLdpEntityAtmLRMinVpi,
                      mplsLdpEntityAtmLRMinVci
                   }
       ::= { mplsLdpEntityAtmLRTable 1 }

   MplsLdpEntityAtmLREntry ::= SEQUENCE {
       mplsLdpEntityAtmLRMinVpi       AtmVpIdentifier,
       mplsLdpEntityAtmLRMinVci       MplsAtmVcIdentifier,
       mplsLdpEntityAtmLRMaxVpi       AtmVpIdentifier,
       mplsLdpEntityAtmLRMaxVci       MplsAtmVcIdentifier,
       mplsLdpEntityAtmLRStorageType  StorageType,
       mplsLdpEntityAtmLRRowStatus    RowStatus
   }

   mplsLdpEntityAtmLRMinVpi OBJECT-TYPE
       SYNTAX AtmVpIdentifier
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "The minimum VPI number configured for this range.
           The value of zero is a valid value for the VPI portion
           of the label."
       ::= { mplsLdpEntityAtmLREntry 1 }

   mplsLdpEntityAtmLRMinVci OBJECT-TYPE
       SYNTAX MplsAtmVcIdentifier
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "The minimum VCI number configured for this range."
       ::= { mplsLdpEntityAtmLREntry 2 }

   mplsLdpEntityAtmLRMaxVpi OBJECT-TYPE
       SYNTAX AtmVpIdentifier
       MAX-ACCESS read-create



RFC 3815                      MPLS LDP MIB                     June 2004


       STATUS current
       DESCRIPTION
           "The maximum VPI number configured for this range."
       ::= { mplsLdpEntityAtmLREntry 3 }

   mplsLdpEntityAtmLRMaxVci OBJECT-TYPE
       SYNTAX MplsAtmVcIdentifier
       MAX-ACCESS read-create
       STATUS current
       DESCRIPTION
           "The maximum VCI number configured for this range."
      ::= { mplsLdpEntityAtmLREntry 4 }

   mplsLdpEntityAtmLRStorageType  OBJECT-TYPE
       SYNTAX      StorageType
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The storage type for this conceptual row.
           Conceptual rows having the value 'permanent(4)'
           need not allow write-access to any columnar
           objects in the row."
       DEFVAL { nonVolatile }
       ::= { mplsLdpEntityAtmLREntry 5 }

   mplsLdpEntityAtmLRRowStatus OBJECT-TYPE
       SYNTAX RowStatus
       MAX-ACCESS read-create
       STATUS current
       DESCRIPTION
           "The status of this conceptual row.  All writable
            objects in this row may be modified at any time,
            however, as described in detail in the section
            entitled, 'Changing Values After Session
            Establishment', and again described in the
            DESCRIPTION clause of the
            mplsLdpEntityAdminStatus object,
            if a session has been initiated with a Peer,
            changing objects in this table will
            wreak havoc with the session and interrupt traffic.
            To repeat again:  the recommended procedure
            is to set the mplsLdpEntityAdminStatus to
            down, thereby explicitly causing a session
            to be torn down. Then, change objects in this
            entry, then set the mplsLdpEntityAdminStatus
            to enable which enables a new session
            to be initiated."
       ::= { mplsLdpEntityAtmLREntry 6 }



RFC 3815                      MPLS LDP MIB                     June 2004


   --
   -- MPLS LDP ATM Session Information
   --

   mplsLdpAtmSessionObjects OBJECT IDENTIFIER ::=
                                  { mplsLdpAtmObjects 2 }

   mplsLdpAtmSessionTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF MplsLdpAtmSessionEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table which relates sessions in the
           'mplsLdpSessionTable' and their label
           range intersections.  There could be one
           or more label range intersections between an
           LDP Entity and LDP Peer using ATM as the
           underlying  media.  Each row represents
           a single label range intersection.

           This table cannot use the 'AUGMENTS'
           clause because there is not necessarily
           a one-to-one mapping between this table
           and the mplsLdpSessionTable."
       ::= { mplsLdpAtmSessionObjects 1 }

   mplsLdpAtmSessionEntry OBJECT-TYPE
       SYNTAX      MplsLdpAtmSessionEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry in this table represents information on a
           single label range intersection between an LDP Entity
           and LDP Peer.

           The information contained in a row is read-only."
       INDEX       { mplsLdpEntityLdpId,
                     mplsLdpEntityIndex,
                     mplsLdpPeerLdpId,
                     mplsLdpSessionAtmLRLowerBoundVpi,
                     mplsLdpSessionAtmLRLowerBoundVci
                   }
       ::= { mplsLdpAtmSessionTable 1 }

   MplsLdpAtmSessionEntry ::= SEQUENCE {
       mplsLdpSessionAtmLRLowerBoundVpi     AtmVpIdentifier,
       mplsLdpSessionAtmLRLowerBoundVci     MplsAtmVcIdentifier,
       mplsLdpSessionAtmLRUpperBoundVpi     AtmVpIdentifier,



RFC 3815                      MPLS LDP MIB                     June 2004


       mplsLdpSessionAtmLRUpperBoundVci     MplsAtmVcIdentifier
   }

   mplsLdpSessionAtmLRLowerBoundVpi OBJECT-TYPE
       SYNTAX AtmVpIdentifier
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "The minimum VPI number for this range."
       ::= { mplsLdpAtmSessionEntry 1 }

   mplsLdpSessionAtmLRLowerBoundVci OBJECT-TYPE
       SYNTAX MplsAtmVcIdentifier
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "The minimum VCI number for this range."
       ::= { mplsLdpAtmSessionEntry 2 }

   mplsLdpSessionAtmLRUpperBoundVpi OBJECT-TYPE
       SYNTAX AtmVpIdentifier
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The maximum VPI number for this range."
       ::= { mplsLdpAtmSessionEntry 3 }

   mplsLdpSessionAtmLRUpperBoundVci OBJECT-TYPE
       SYNTAX MplsAtmVcIdentifier
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The maximum VCI number for this range."
       ::= { mplsLdpAtmSessionEntry 4 }

   --**************************************************************
   -- Module Conformance Statement
   --**************************************************************

   mplsLdpAtmGroups
       OBJECT IDENTIFIER ::= { mplsLdpAtmConformance 1 }

   mplsLdpAtmCompliances
       OBJECT IDENTIFIER ::= { mplsLdpAtmConformance 2 }

   --
   -- Full Compliance
   --



RFC 3815                      MPLS LDP MIB                     June 2004


   mplsLdpAtmModuleFullCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "The Module is implemented with support for
           read-create and read-write.  In other words,
           both monitoring and configuration
           are available when using this MODULE-COMPLIANCE."
       MODULE -- this module
       MANDATORY-GROUPS    {
                              mplsLdpAtmGroup
                           }


       OBJECT       mplsLdpEntityAtmRowStatus
       SYNTAX       RowStatus { active(1) }
       WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
       DESCRIPTION
          "Support for createAndWait and notInService is not required."

       OBJECT       mplsLdpEntityAtmLRRowStatus
       SYNTAX       RowStatus { active(1) }
       WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
       DESCRIPTION
          "Support for createAndWait and notInService is not required."

       ::= { mplsLdpAtmCompliances 1 }

   --
   -- Read-Only Compliance
   --

   mplsLdpAtmModuleReadOnlyCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "The Module is implemented with support for
           read-only.  In other words, only monitoring
           is available by implementing this MODULE-COMPLIANCE."
       MODULE -- this module
       MANDATORY-GROUPS    {
                              mplsLdpAtmGroup
                           }

       OBJECT       mplsLdpEntityAtmIfIndexOrZero
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmMergeCap



RFC 3815                      MPLS LDP MIB                     June 2004


       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmVcDirectionality
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmLsrConnectivity
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmDefaultControlVpi
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmDefaultControlVci
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmUnlabTrafVpi
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmUnlabTrafVci
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmStorageType
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmRowStatus
       SYNTAX       RowStatus { active(1) }
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required, and active is the
          only status that needs to be supported."

       OBJECT       mplsLdpEntityAtmLRMaxVpi
       MIN-ACCESS   read-only



RFC 3815                      MPLS LDP MIB                     June 2004


       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmLRMaxVci
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmLRStorageType
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityAtmLRRowStatus
       SYNTAX       RowStatus { active(1) }
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required, and active is the
          only status that needs to be supported."

       ::= { mplsLdpAtmCompliances 2 }

   --
   -- units of conformance
   --

   mplsLdpAtmGroup OBJECT-GROUP
       OBJECTS {
       mplsLdpEntityAtmIfIndexOrZero,
       mplsLdpEntityAtmMergeCap,
       mplsLdpEntityAtmLRComponents,
       mplsLdpEntityAtmVcDirectionality,
       mplsLdpEntityAtmLsrConnectivity,
       mplsLdpEntityAtmDefaultControlVpi,
       mplsLdpEntityAtmDefaultControlVci,
       mplsLdpEntityAtmUnlabTrafVpi,
       mplsLdpEntityAtmUnlabTrafVci,
       mplsLdpEntityAtmStorageType,
       mplsLdpEntityAtmRowStatus,
       mplsLdpEntityAtmLRMaxVpi,
       mplsLdpEntityAtmLRMaxVci,
       mplsLdpEntityAtmLRStorageType,
       mplsLdpEntityAtmLRRowStatus,
       mplsLdpSessionAtmLRUpperBoundVpi,
       mplsLdpSessionAtmLRUpperBoundVci

       }
       STATUS    current



RFC 3815                      MPLS LDP MIB                     June 2004


       DESCRIPTION
           "Objects that apply to all MPLS LDP implementations
           using ATM as the Layer 2."
       ::= { mplsLdpAtmGroups 1 }

   END

4.2.  The MPLS-LDP-FRAME-RELAY-STD-MIB Module

   This MIB Module MUST be supported if LDP uses FRAME RELAY as the
   Layer 2 medium.  There are three tables in this MIB Module.  Two
   tables are to configure LDP for using Frame Relay.  These tables are
   the mplsLdpEntityFrameRelayTable and the
   mplsLdpEntityFrameRelayLRTable.  The third table,
   mplsLdpFrameRelaySessionTable, is a read-only table.  This MIB Module
   IMPORTS the DLCI TEXTUAL-CONVENTION from [RFC2115].

4.2.1.  The LDP Entity Frame Relay Table

   The mplsLdpEntityFrameRelayTable provides a way to configure
   information which would be contained in the "Optional Parameter"
   portion of an LDP PDU Initialization Message.

4.2.2.  The LDP Entity Frame Relay Label Range Table

   The mplsLdpEntityFrameRelayLRTable provides a way to configure
   information which would be contained in the "Frame Relay Label Range
   Components" portion of an LDP PDU Intialization Message, see
   [RFC3034] and [RFC3036].

4.2.3.  The LDP Frame Relay Session Table

   The mplsLdpFrameRelaySessionTable is a table which contains session
   information specific to Frame Relay.

   MPLS-LDP-FRAME-RELAY-STD-MIB DEFINITIONS ::= BEGIN

   IMPORTS
       OBJECT-TYPE,
       MODULE-IDENTITY,
       Unsigned32
           FROM SNMPv2-SMI                                 --  [RFC2578]
       MODULE-COMPLIANCE,
       OBJECT-GROUP
           FROM SNMPv2-CONF                                --  [RFC2580]

       RowStatus,
       StorageType



RFC 3815                      MPLS LDP MIB                     June 2004


           FROM SNMPv2-TC                                  --  [RFC2579]

       DLCI
           FROM FRAME-RELAY-DTE-MIB                        --  [RFC2115]

       InterfaceIndexOrZero
           FROM IF-MIB                                     --  [RFC2020]

       mplsStdMIB
           FROM MPLS-TC-STD-MIB                            --  [RFC3811]

       mplsLdpEntityLdpId,
       mplsLdpEntityIndex,
       mplsLdpPeerLdpId
           FROM MPLS-LDP-STD-MIB                           --  [RFC3813]
       ;

   mplsLdpFrameRelayStdMIB MODULE-IDENTITY
       LAST-UPDATED "200406030000Z"  -- June 3, 2004
       ORGANIZATION "Multiprotocol Label Switching (mpls)
                     Working Group"
       CONTACT-INFO
           "Joan Cucchiara (jcucchiara@mindspring.com)
            Marconi Communications, Inc.

            Hans Sjostrand (hans@ipunplugged.com)
            ipUnplugged

            James V. Luciani (james_luciani@mindspring.com)
            Marconi Communications, Inc.

            Working Group Chairs:
            George Swallow,   email: swallow@cisco.com
            Loa Andersson,    email: loa@pi.se

            MPLS Working Group, email: mpls@uu.net
       "
       DESCRIPTION
           "Copyright (C) The Internet Society (year). The
           initial version of this MIB module was published
           in RFC 3815. For full legal notices see the RFC
           itself or see:
           http://www.ietf.org/copyrights/ianamib.html

           This MIB contains managed object definitions for
           configuring and monitoring the Multiprotocol Label
           Switching (MPLS), Label Distribution Protocol (LDP),
           utilizing Frame Relay as the Layer 2 media."



RFC 3815                      MPLS LDP MIB                     June 2004


       REVISION "200406030000Z"  -- June 6, 2004
       DESCRIPTION
           "Initial version published as part of RFC 3815."

       ::= { mplsStdMIB 6 }

   --****************************************************************

   mplsLdpFrameRelayObjects  OBJECT IDENTIFIER
                              ::= { mplsLdpFrameRelayStdMIB 1 }

   mplsLdpFrameRelayConformance   OBJECT IDENTIFIER
                              ::= { mplsLdpFrameRelayStdMIB 2 }

   --****************************************************************
   -- MPLS LDP Frame Relay Objects
   --****************************************************************

   --
   -- Ldp Entity Objects for Frame Relay
   --

   mplsLdpEntityFrameRelayObjects OBJECT IDENTIFIER ::=
                                       { mplsLdpFrameRelayObjects 1 }

   mplsLdpEntityFrameRelayTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF MplsLdpEntityFrameRelayEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table contains Frame Relay specific
           information which could be used in the
           'Optional Parameters' and other Frame Relay
           specific information.

           This table 'sparse augments' the mplsLdpEntityTable
           when Frame Relay is the Layer 2 medium."
       ::= { mplsLdpEntityFrameRelayObjects 1 }

   mplsLdpEntityFrameRelayEntry OBJECT-TYPE
       SYNTAX      MplsLdpEntityFrameRelayEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry in this table represents the Frame Relay
           optional parameters associated with the LDP entity."
       INDEX       {  mplsLdpEntityLdpId,
                      mplsLdpEntityIndex



RFC 3815                      MPLS LDP MIB                     June 2004


                   }
       ::= { mplsLdpEntityFrameRelayTable 1 }

   MplsLdpEntityFrameRelayEntry ::= SEQUENCE {
       mplsLdpEntityFrameRelayIfIndexOrZero        InterfaceIndexOrZero,
       mplsLdpEntityFrameRelayMergeCap             INTEGER,
       mplsLdpEntityFrameRelayLRComponents         Unsigned32,
       mplsLdpEntityFrameRelayVcDirectionality     INTEGER,
       mplsLdpEntityFrameRelayStorageType          StorageType,
       mplsLdpEntityFrameRelayRowStatus            RowStatus
   }

   mplsLdpEntityFrameRelayIfIndexOrZero OBJECT-TYPE
       SYNTAX      InterfaceIndexOrZero
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
          "This value represents either the InterfaceIndex of
          the 'ifLayer' where the Frame Relay Labels 'owned' by this
          entry were created, or 0 (zero).  The value of zero
          means that the InterfaceIndex is not known.  For example,
          if the InterfaceIndex is created subsequent to the
          Frame Relay Label's creation, then it would not be known.
          However, if the InterfaceIndex is known, then it must
          be represented by this value.

          If an InterfaceIndex becomes known, then the
          network management entity (e.g., SNMP agent) responsible
          for this object MUST change the value from 0 (zero) to the
          value of the InterfaceIndex.  If an Frame Relay Label is
          being used in forwarding data, then the value of this
          object MUST be the InterfaceIndex."
       ::= { mplsLdpEntityFrameRelayEntry 1 }

   mplsLdpEntityFrameRelayMergeCap OBJECT-TYPE
       SYNTAX      INTEGER {
                       notSupported(0),
                       supported(1)
                   }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This represents whether or not the Frame Relay merge
           capability is supported.  This is the EXACT value for the
           Frame Relay Session Parameter, field M (for Frame Relay
           Merge Capabilities).  The Frame Relay Session Parameter
           is an optional parameter in the Initialization Message.




RFC 3815                      MPLS LDP MIB                     June 2004


           The description from rfc3036.txt is:
           'M, Frame Relay Merge Capabilities
              Specifies the merge capabilities of a Frame
              Relay switch.  The following values are
              supported in this version of the
              specification:

                     Value          Meaning

                       0            Merge not supported
                       1            Merge supported

              Non-merge and merge Frame Relay LSRs may
              freely interoperate.'

              Please refer to the following reference for a
              complete description of this feature."
        REFERENCE
           "RFC3036, LDP Specification, Section 3.5.3
           Initialization Message."
       ::= { mplsLdpEntityFrameRelayEntry 2 }

   mplsLdpEntityFrameRelayLRComponents OBJECT-TYPE
       SYNTAX      Unsigned32 (1..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "Number of Label Range Components in the Initialization
           message.  This also represents the number of entries
           in the mplsLdpEntityFrameRelayLRTable which correspond
           to this entry.

           This is the EXACT value for the Frame Relay Session
           Parameter, field N (for Number of label range
           components).  The Frame Relay Session Parameter
           is an optional parameter in the Initialization
           Message.

           The description from rfc3036.txt is:

           'N, Number of label range components
               Specifies the number of Frame Relay Label
               Range Components included in the TLV.'

            Please refer to the following reference for a
            complete description of this feature."
        REFERENCE
           "RFC3036, LDP Specification, Section 3.5.3



RFC 3815                      MPLS LDP MIB                     June 2004


           Initialization Message."
       ::= { mplsLdpEntityFrameRelayEntry 3 }

   mplsLdpEntityFrameRelayVcDirectionality OBJECT-TYPE
       SYNTAX      INTEGER {
                             bidirectional(0),
                             unidirection(1)
                           }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "If the value of this object is 'bidirectional(0)', then
           the LSR supports the use of a given DLCI as a label for
           both directions independently.  If the value of
           this object is 'unidirectional(1)', then the LSR
           uses the given DLCI as a label in only one direction.

           This is the EXACT value for the Frame Relay Session
           Parameter, field D (for VC Directionality).  The
           Frame Relay Session Parameter is an optional
           parameter in the Initialization Message.

           The description from rfc3036.txt is:

           'D, VC Directionality
              A value of 0 specifies bidirectional VC capability,
              meaning the LSR can support the use of a given
              DLCI as a label for both link directions
              independently.  A value of 1 specifies
              unidirectional VC capability, meaning a given
              DLCI may appear in a label mapping for one
              direction on the link only.  When either or both
              of the peers specifies unidirectional VC
              capability, both LSRs use unidirectional VC
              label assignment for the link as follows.  The
              LSRs compare their LDP Identifiers as unsigned
              integers.  The LSR with the larger LDP
              Identifier may assign only odd-numbered DLCIs
              in the range as labels.  The system with the
              smaller LDP Identifier may assign only
              even-numbered DLCIs in the range as labels.'

              Please refer to the following reference for a
              complete description of this feature."
        REFERENCE
           "RFC3036, LDP Specification, Section 3.5.3
           Initialization Message."
       ::= { mplsLdpEntityFrameRelayEntry 4 }



RFC 3815                      MPLS LDP MIB                     June 2004


   mplsLdpEntityFrameRelayStorageType  OBJECT-TYPE
       SYNTAX      StorageType
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The storage type for this conceptual row.
           Conceptual rows having the value 'permanent(4)'
           need not allow write-access to any columnar
           objects in the row."
       DEFVAL { nonVolatile }
       ::= { mplsLdpEntityFrameRelayEntry 5 }

   mplsLdpEntityFrameRelayRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The status of this conceptual row.  All writable
            objects in this row may be modified at any time,
            however, as described in detail in the section
            entitled, 'Changing Values After Session
            Establishment', and again described in the
            DESCRIPTION clause of the
            mplsLdpEntityAdminStatus object,
            if a session has been initiated with a Peer,
            changing objects in this table will
            wreak havoc with the session and interrupt
            traffic.  To repeat again:
            the recommended procedure is to set the
            mplsLdpEntityAdminStatus to
            down, thereby explicitly causing a
            session to be torn down. Then,
            change objects in this entry, then set
            the mplsLdpEntityAdminStatus
            to enable which enables a new session
            to be initiated."
       ::= { mplsLdpEntityFrameRelayEntry 6 }

   --
   -- Frame Relay Label Range Components
   --

   mplsLdpEntityFrameRelayLRTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF MplsLdpEntityFrameRelayLREntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table contains information about the



RFC 3815                      MPLS LDP MIB                     June 2004


           Optional Parameters for the Frame Relay Session
           in the LDP Initialization Message, specifically
           it contains information about the Frame Relay
           Label Range Components.

           If the value of the object
           'mplsLdpEntityOptionalParameters' contains the
           value of 'frameRelaySessionParameters(3)' then
           there must be at least one corresponding entry
           in this table."
       ::= { mplsLdpEntityFrameRelayObjects 2 }

   mplsLdpEntityFrameRelayLREntry OBJECT-TYPE
       SYNTAX      MplsLdpEntityFrameRelayLREntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry in this table represents the Frame Relay
           Label Range Component associated with the LDP entity."
       INDEX       {  mplsLdpEntityLdpId,
                      mplsLdpEntityIndex,
                      mplsLdpEntityFrameRelayLRMinDlci
                   }
       ::= { mplsLdpEntityFrameRelayLRTable 1 }

   MplsLdpEntityFrameRelayLREntry ::= SEQUENCE {
       mplsLdpEntityFrameRelayLRMinDlci              DLCI,
       mplsLdpEntityFrameRelayLRMaxDlci              DLCI,
       mplsLdpEntityFrameRelayLRLen                  INTEGER,
       mplsLdpEntityFrameRelayLRStorageType          StorageType,
       mplsLdpEntityFrameRelayLRRowStatus            RowStatus
   }

   mplsLdpEntityFrameRelayLRMinDlci OBJECT-TYPE
       SYNTAX      DLCI
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The lower bound which is supported.  This value
           should be the same as that in the Frame Relay Label
           Range Component's Minimum DLCI field.  The value
           of zero is valid for the minimum DLCI field of
           the label."
       REFERENCE
           "RFC3034, Use of Label Switching on Frame Relay
           Networks Specification."
       ::= { mplsLdpEntityFrameRelayLREntry 1 }




RFC 3815                      MPLS LDP MIB                     June 2004


   mplsLdpEntityFrameRelayLRMaxDlci OBJECT-TYPE
       SYNTAX      DLCI
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The upper bound which is supported.  This value
           should be the same as that in the Frame Relay Label
           Range Component's Maximum DLCI field."
       ::= { mplsLdpEntityFrameRelayLREntry 2 }

   mplsLdpEntityFrameRelayLRLen OBJECT-TYPE
       SYNTAX      INTEGER {
                       tenDlciBits(0),
                       twentyThreeDlciBits(2)
                   }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This object specifies the length of the DLCI bits.

           This is the EXACT value for the Len field of the
           Frame Relay Label Range Component.

           The description from rfc3036.txt is:

           'Len
               This field specifies the number of bits of the DLCI.
               The following values are supported:

                    Len    DLCI bits

                    0       10
                    2       23

               Len values 1 and 3 are reserved.'

            Please refer to the following reference for a complete
            description of this feature."
        REFERENCE
           "RFC3036, LDP Specification, Section 3.5.3
           Initialization Message."
       ::= { mplsLdpEntityFrameRelayLREntry 3 }

   mplsLdpEntityFrameRelayLRStorageType  OBJECT-TYPE
       SYNTAX      StorageType
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION



RFC 3815                      MPLS LDP MIB                     June 2004


           "The storage type for this conceptual row.
           Conceptual rows having the value 'permanent(4)'
           need not allow write-access to any columnar
           objects in the row."
       DEFVAL { nonVolatile }
       ::= { mplsLdpEntityFrameRelayLREntry 4 }

   mplsLdpEntityFrameRelayLRRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The status of this conceptual row.  All writable
            objects in this row may be modified at any time,
            however, as described in detail in the section
            entitled, 'Changing Values After Session
            Establishment', and again described in the
            DESCRIPTION clause of the
            mplsLdpEntityAdminStatus object,
            if a session has been initiated with a Peer,
            changing objects in this table will
            wreak havoc with the session and interrupt
            traffic.  To repeat again:
            the recommended procedure is to set the
            mplsLdpEntityAdminStatus to down, thereby
            explicitly causing a session to be torn down. Then,
            change objects in this entry, then set the
            mplsLdpEntityAdminStatus to enable which enables
            a new session to be initiated."
       ::= { mplsLdpEntityFrameRelayLREntry 5 }

   --
   -- MPLS LDP Frame Relay Session Information
   --

   mplsLdpFrameRelaySessionObjects  OBJECT IDENTIFIER ::=
                              { mplsLdpFrameRelayObjects  2 }

   mplsLdpFrameRelaySessionTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF MplsLdpFrameRelaySessionEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table of Frame Relay label range intersections
           between the LDP Entities and LDP Peers.
           Each row represents a single label range intersection.

           NOTE:  this table cannot use the 'AUGMENTS'



RFC 3815                      MPLS LDP MIB                     June 2004


           clause because there is not necessarily a one-to-one
           mapping between this table and the
           mplsLdpSessionTable."
       ::= { mplsLdpFrameRelaySessionObjects 1 }

   mplsLdpFrameRelaySessionEntry OBJECT-TYPE
       SYNTAX      MplsLdpFrameRelaySessionEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry in this table represents information on a
           single label range intersection between an
           LDP Entity and LDP Peer.

           The information contained in a row is read-only."
       INDEX       { mplsLdpEntityLdpId,
                     mplsLdpEntityIndex,
                     mplsLdpPeerLdpId,
                     mplsLdpFrameRelaySessionMinDlci
                   }
       ::= { mplsLdpFrameRelaySessionTable 1 }

   MplsLdpFrameRelaySessionEntry ::= SEQUENCE {
       mplsLdpFrameRelaySessionMinDlci    DLCI,
       mplsLdpFrameRelaySessionMaxDlci    DLCI,
       mplsLdpFrameRelaySessionLen        INTEGER
   }

   mplsLdpFrameRelaySessionMinDlci OBJECT-TYPE
       SYNTAX      DLCI
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The lower bound of DLCIs which are supported.
           The value of zero is a valid value for the
           minimum DLCI field of the label."
       REFERENCE
           "RFC3034, Use of Label Switching on Frame Relay
           Networks Specification."
       ::= { mplsLdpFrameRelaySessionEntry 1 }

   mplsLdpFrameRelaySessionMaxDlci OBJECT-TYPE
       SYNTAX      DLCI
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The upper bound of DLCIs which are supported."
       ::= { mplsLdpFrameRelaySessionEntry 2 }



RFC 3815                      MPLS LDP MIB                     June 2004


   mplsLdpFrameRelaySessionLen OBJECT-TYPE
       SYNTAX      INTEGER {
                       tenDlciBits(0),
                       twentyThreeDlciBits(2)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "This object specifies the DLCI bits."
       ::= { mplsLdpFrameRelaySessionEntry 3 }

   --****************************************************************
   -- Module Conformance Statement
   --****************************************************************

   mplsLdpFrameRelayGroups
       OBJECT IDENTIFIER ::= { mplsLdpFrameRelayConformance 1 }

   mplsLdpFrameRelayCompliances
       OBJECT IDENTIFIER ::= { mplsLdpFrameRelayConformance 2 }

   --
   -- Full Compliance
   --

   mplsLdpFrameRelayModuleFullCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "The Module is implemented with support for
           read-create and read-write.  In other words,
           both monitoring and configuration
           are available when using this MODULE-COMPLIANCE."
       MODULE -- this module
           MANDATORY-GROUPS    {
                                  mplsLdpFrameRelayGroup
                               }

       OBJECT       mplsLdpEntityFrameRelayRowStatus
       SYNTAX       RowStatus { active(1) }
       WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
       DESCRIPTION
          "Support for createAndWait and notInService is not required."

       OBJECT       mplsLdpEntityFrameRelayLRRowStatus
       SYNTAX       RowStatus { active(1) }
       WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
       DESCRIPTION
          "Support for createAndWait and notInService is not required."



RFC 3815                      MPLS LDP MIB                     June 2004


       ::= { mplsLdpFrameRelayCompliances 1 }

   --
   -- Read-Only Compliance
   --

   mplsLdpFrameRelayModuleReadOnlyCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "The Module is implemented with support for
           read-only.  In other words, only monitoring
           is available by implementing this MODULE-COMPLIANCE."
       MODULE -- this module
           MANDATORY-GROUPS    {
                                  mplsLdpFrameRelayGroup
                               }

       OBJECT       mplsLdpEntityFrameRelayIfIndexOrZero
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityFrameRelayMergeCap
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityFrameRelayVcDirectionality
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityFrameRelayStorageType
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityFrameRelayRowStatus
       SYNTAX       RowStatus { active(1) }
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required, and active is the
          only status that needs to be supported."

       OBJECT       mplsLdpEntityFrameRelayLRMaxDlci
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."



RFC 3815                      MPLS LDP MIB                     June 2004


       OBJECT       mplsLdpEntityFrameRelayLRLen
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityFrameRelayLRStorageType
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityFrameRelayLRRowStatus
       SYNTAX       RowStatus { active(1) }
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required, and active is the
          only status that needs to be supported."
       ::= { mplsLdpFrameRelayCompliances 2 }

   --
   -- units of conformance
   --

   mplsLdpFrameRelayGroup OBJECT-GROUP
       OBJECTS {
       mplsLdpEntityFrameRelayIfIndexOrZero,
       mplsLdpEntityFrameRelayMergeCap,
       mplsLdpEntityFrameRelayLRComponents,
       mplsLdpEntityFrameRelayVcDirectionality,
       mplsLdpEntityFrameRelayStorageType,
       mplsLdpEntityFrameRelayRowStatus,
       mplsLdpEntityFrameRelayLRMaxDlci,
       mplsLdpEntityFrameRelayLRLen,
       mplsLdpEntityFrameRelayLRStorageType,
       mplsLdpEntityFrameRelayLRRowStatus,
       mplsLdpFrameRelaySessionMaxDlci,
       mplsLdpFrameRelaySessionLen
       }
       STATUS    current
       DESCRIPTION
           "Objects that apply to all MPLS LDP implementations
           using Frame Relay as the Layer 2."
       ::= { mplsLdpFrameRelayGroups 1 }

   END







RFC 3815                      MPLS LDP MIB                     June 2004


4.3.  The MPLS-LDP-GENERIC-STD-MIB Module

   This MIB Module MUST be supported if LDP uses a Per Platform Label
   Space.  This MIB Module contains a Label Range (LR) table for
   configuring MPLS Generic Label Ranges.  This table is
   mplsLdpEntityGenericLRTable.  Although the LDP Specification does not
   provide a way for configuring Label Ranges for Generic Labels, the
   MIB does provide a way to reserve a range of generic labels because
   this was thought to be useful by the working group.

   MPLS-LDP-GENERIC-STD-MIB DEFINITIONS ::= BEGIN

   IMPORTS
       OBJECT-TYPE,
       MODULE-IDENTITY,
       Unsigned32
           FROM SNMPv2-SMI                                  -- [RFC2578]

       MODULE-COMPLIANCE,
       OBJECT-GROUP
           FROM SNMPv2-CONF                                 -- [RFC2580]

       RowStatus,
       StorageType
           FROM SNMPv2-TC                                   -- [RFC2579]

       InterfaceIndexOrZero
           FROM IF-MIB                                      -- [RFC2020]

       mplsStdMIB
           FROM MPLS-TC-STD-MIB                             -- [RFC3811]

       mplsLdpEntityLdpId,
       mplsLdpEntityIndex
           FROM MPLS-LDP-STD-MIB                            -- [RFC3813]
       ;

   mplsLdpGenericStdMIB MODULE-IDENTITY
       LAST-UPDATED "200406030000Z"  -- June 6, 2004
       ORGANIZATION "Multiprotocol Label Switching (mpls)
                     Working Group"
       CONTACT-INFO
           "Joan Cucchiara (jcucchiara@mindspring.com)
            Marconi Communications, Inc.

            Hans Sjostrand (hans@ipunplugged.com)
            ipUnplugged




RFC 3815                      MPLS LDP MIB                     June 2004


            James V. Luciani (james_luciani@mindspring.com)
            Marconi Communications, Inc.

            Working Group Chairs:
            George Swallow,   email: swallow@cisco.com
            Loa Andersson,    email: loa@pi.se

            MPLS Working Group, email: mpls@uu.net
       "
       DESCRIPTION
           "Copyright (C) The Internet Society (year). The
           initial version of this MIB module was published
           in RFC 3815. For full legal notices see the RFC
           itself or see:
           http://www.ietf.org/copyrights/ianamib.html

           This MIB contains managed object definitions for
           configuring and monitoring the Multiprotocol Label
           Switching (MPLS), Label Distribution Protocol (LDP),
           utilizing ethernet as the Layer 2 media."
       REVISION "200406030000Z"  -- June 6, 2004
       DESCRIPTION
           "Initial version published as part of RFC 3815."

       ::= { mplsStdMIB 7 }

   --****************************************************************

   mplsLdpGenericObjects
            OBJECT IDENTIFIER ::= { mplsLdpGenericStdMIB 1 }
   mplsLdpGenericConformance
            OBJECT IDENTIFIER ::= { mplsLdpGenericStdMIB 2 }

   --****************************************************************
   -- MPLS LDP GENERIC Objects
   --****************************************************************

   --
   -- Ldp Entity Objects for Generic Labels
   --

   mplsLdpEntityGenericObjects  OBJECT IDENTIFIER ::=
                                 { mplsLdpGenericObjects 1 }

   --
   -- The MPLS LDP Entity Generic Label Range Table
   --




RFC 3815                      MPLS LDP MIB                     June 2004


   mplsLdpEntityGenericLRTable OBJECT-TYPE
       SYNTAX SEQUENCE OF MplsLdpEntityGenericLREntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "The MPLS LDP Entity Generic Label Range (LR)
           Table.

           The purpose of this table is to provide a mechanism
           for configurating a contiguous range of generic labels,
           or a 'label range' for LDP Entities.

           LDP Entities which use Generic Labels must have at least
           one entry in this table.  In other words, this table
           'extends' the mpldLdpEntityTable for Generic Labels."
       ::= { mplsLdpEntityGenericObjects 1 }

   mplsLdpEntityGenericLREntry OBJECT-TYPE
       SYNTAX MplsLdpEntityGenericLREntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "A row in the LDP Entity Generic Label
           Range (LR) Table.  One entry in this table contains
           information on a single range of labels
           represented by the configured Upper and Lower
           Bounds pairs.  NOTE: there is NO corresponding
           LDP message which relates to the information
           in this table, however, this table does provide
           a way for a user to 'reserve' a generic label
           range.

           NOTE:  The ranges for a specific LDP Entity
           are UNIQUE and non-overlapping.

           A row will not be created unless a unique and
           non-overlapping range is specified."
       INDEX       {  mplsLdpEntityLdpId,
                      mplsLdpEntityIndex,
                      mplsLdpEntityGenericLRMin,
                      mplsLdpEntityGenericLRMax
                   }
       ::= { mplsLdpEntityGenericLRTable 1 }

   MplsLdpEntityGenericLREntry ::= SEQUENCE {
       mplsLdpEntityGenericLRMin           Unsigned32,
       mplsLdpEntityGenericLRMax           Unsigned32,
       mplsLdpEntityGenericLabelSpace      INTEGER,



RFC 3815                      MPLS LDP MIB                     June 2004


       mplsLdpEntityGenericIfIndexOrZero   InterfaceIndexOrZero,
       mplsLdpEntityGenericLRStorageType   StorageType,
       mplsLdpEntityGenericLRRowStatus     RowStatus
   }

   mplsLdpEntityGenericLRMin OBJECT-TYPE
       SYNTAX     Unsigned32(0..1048575)
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
           "The minimum label configured for this range."
       ::= { mplsLdpEntityGenericLREntry 1 }

   mplsLdpEntityGenericLRMax OBJECT-TYPE
       SYNTAX     Unsigned32(0..1048575)
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
           "The maximum label configured for this range."
       ::= { mplsLdpEntityGenericLREntry 2 }

   mplsLdpEntityGenericLabelSpace  OBJECT-TYPE
       SYNTAX      INTEGER {
                             perPlatform(1),
                             perInterface(2)
                            }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
          "This value of this object is perPlatform(1), then
          this means that the label space type is
          per platform.

          If this object is perInterface(2), then this
          means that the label space type is per Interface."
       REFERENCE
           "RFC3036, LDP Specification, Section 2.2.1,
           Label Spaces."
       DEFVAL { perPlatform }
       ::= { mplsLdpEntityGenericLREntry 3 }

   mplsLdpEntityGenericIfIndexOrZero OBJECT-TYPE
       SYNTAX      InterfaceIndexOrZero
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
          "This value represents either the InterfaceIndex of
          the 'ifLayer' where these Generic Label would be created,



RFC 3815                      MPLS LDP MIB                     June 2004


          or 0 (zero).  The value of zero means that the
          InterfaceIndex is not known.

          However, if the InterfaceIndex is known,
          then it must be represented by this value.

          If an InterfaceIndex becomes known, then the
          network management entity (e.g., SNMP agent) responsible
          for this object MUST change the value from 0 (zero) to the
          value of the InterfaceIndex."
       ::= { mplsLdpEntityGenericLREntry 4 }

   mplsLdpEntityGenericLRStorageType  OBJECT-TYPE
       SYNTAX      StorageType
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The storage type for this conceptual row.
           Conceptual rows having the value 'permanent(4)'
           need not allow write-access to any columnar
           objects in the row."
       DEFVAL { nonVolatile }
       ::= { mplsLdpEntityGenericLREntry 5 }

   mplsLdpEntityGenericLRRowStatus OBJECT-TYPE
       SYNTAX RowStatus
       MAX-ACCESS read-create
       STATUS current
       DESCRIPTION
           "The status of this conceptual row.  All writable
            objects in this row may be modified at any time,
            however, as described in  detail in the section
            entitled, 'Changing Values After Session
            Establishment', and again described in the
            DESCRIPTION clause of the mplsLdpEntityAdminStatus object,
            if a session has been initiated with a Peer,
            changing objects in this table will
            wreak havoc with the session and interrupt traffic.
            To repeat again:  the recommended procedure is
            to set the mplsLdpEntityAdminStatus to
            down, thereby explicitly causing a
            session to be torn down. Then, change objects
            in this entry, then set the mplsLdpEntityAdminStatus
            to enable which enables a new session to be initiated.

            There must exist at least one entry in this
            table for every LDP Entity that has a
            generic label configured."



RFC 3815                      MPLS LDP MIB                     June 2004


       ::= { mplsLdpEntityGenericLREntry 6 }

   --****************************************************************
   -- Module Conformance Statement
   --****************************************************************

   mplsLdpGenericGroups
       OBJECT IDENTIFIER ::= { mplsLdpGenericConformance 1 }

   mplsLdpGenericCompliances
       OBJECT IDENTIFIER ::= { mplsLdpGenericConformance 2 }

   --
   -- Full Compliance
   --

   mplsLdpGenericModuleFullCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "The Module is implemented with support for
           read-create and read-write.  In other words,
           both monitoring and configuration
           are available when using this MODULE-COMPLIANCE."
       MODULE -- this module
           MANDATORY-GROUPS    {
                                  mplsLdpGenericGroup
                               }

       OBJECT       mplsLdpEntityGenericLRRowStatus
       SYNTAX       RowStatus { active(1) }
       WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
       DESCRIPTION
          "Support for createAndWait and notInService is not required."

       ::= { mplsLdpGenericCompliances 1 }

   --
   -- Read-Only Compliance
   --

   mplsLdpGenericModuleReadOnlyCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "The Module is implemented with support for
           read-only.  In other words, only monitoring
           is available by implementing this MODULE-COMPLIANCE."
       MODULE -- this module
           MANDATORY-GROUPS    {



RFC 3815                      MPLS LDP MIB                     June 2004


                                  mplsLdpGenericGroup
                               }

       OBJECT       mplsLdpEntityGenericLabelSpace
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityGenericIfIndexOrZero
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityGenericLRStorageType
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required."

       OBJECT       mplsLdpEntityGenericLRRowStatus
       SYNTAX       RowStatus { active(1) }
       MIN-ACCESS   read-only
       DESCRIPTION
          "Write access is not required, and active is the
          only status that needs to be supported."

       ::= { mplsLdpGenericCompliances 2 }

   --
   -- units of conformance
   --

   mplsLdpGenericGroup OBJECT-GROUP
       OBJECTS {
       mplsLdpEntityGenericLabelSpace,
       mplsLdpEntityGenericIfIndexOrZero,
       mplsLdpEntityGenericLRStorageType,
       mplsLdpEntityGenericLRRowStatus
       }
       STATUS    current
       DESCRIPTION
           "Objects that apply to all MPLS LDP implementations
           using Generic Labels as the Layer 2."
       ::= { mplsLdpGenericGroups 1 }

   END






RFC 3815                      MPLS LDP MIB                     June 2004


5.  Acknowledgments

   This document is a product of the MPLS Working Group.  The authors
   would like to thank Mike MacFadden and Adrian Farrel for their
   helpful comments on several reviews.  Also, the authors would like to
   give a special acknowledgement to Bert Wijnen for his many detailed
   reviews.  Bert's assistance and guidance is greatly appreciated.

   We would also like to thank Cheenu Srinivasan, Arun Viswanathan and
   Thomas D. Nadeau, the authors of the MPLS-LSR-STD-MIB [RFC3813], for
   their assistance.

   Additionally, there have been other members of the working group that
   have been very helpful: Alan Kullberg from NetPlane Systems gave
   input on earlier versions of this document, and more recently, Riza
   Cetin of Alcatel and Neil Jerram of Data Connection who both provided
   MIB objects.

   Early versions of this document were also reviewed by colleagues at
   Nortel Networks and Ericsson.  The authors would like to thank the
   following people:  Leigh McLellan, Geetha Brown, Geping Chen and
   Charlan Zhou from Nortel Networks, and Zoltan Takacs and Bo
   Augustsson from Ericsson.

6.  References

6.1.  Normative References

   [RFC2115]   Brown, C. and F. Baker, "Management Information Base for
               Frame Relay DTEs Using SMIv2", RFC 2115, September 1997.

   [RFC2119]   Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2434]   Narten, T. and H. Alvestrand, "Guidelines for Writing an
               IANA Considerations Section in RFCs", BCP: 26, RFC 2434,
               October 1998.

   [RFC2514]   Noto, M., Spiegel, E., and K. Tesink, editors,
               "Definition of Textual Conventions and OBJECT-IDENTITIES
               for ATM Management", RFC 2514, February 1999.

   [RFC2578]   McCloghrie, K., Perkins, D., and J. Schoenwaelder,
               "Structure of Management Information Version 2 (SMIv2)",
               STD 58, RFC 2578, April 1999.






RFC 3815                      MPLS LDP MIB                     June 2004


   [RFC2579]   McCloghrie, K., Perkins, D., and J. Schoenwaelder,
               "Textual Conventions for SMIv2", STD 58, RFC 2579, April
               1999.

   [RFC2580]   McCloghrie, K., Perkins, D., and J. Schoenwaelder,
               "Conformance Statements for SMIv2", STD 58, RFC 2580,
               April 1999.

   [RFC2863]   McCloghrie, K. and F. Kastenholz,  "The Interfaces Group
               MIB", RFC 2863, June 2000.

   [RFC3031]   Rosen, E., Viswananthan, A., and R. Callon,
               "Multiprotocol Label Switching Architecture", RFC 3031,
               January 2001.

   [RFC3032]   Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
               Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
               Encoding", RFC 3032, January 2001.

   [RFC3034]   Conta, A., Doolan, P., and A. Malis, "Use of Label
               Switching on Frame Relay Networks Specification", RFC
               3034, January 2001.

   [RFC3035]   Davie, B., Lawrence, J., McCloghrie, K., Rosen, E.,
               Swallow, G., Rekhter, Y., and P. Doolan, "MPLS using LDP
               and ATM VC Switching", RFC 3035, January 2001.

   [RFC3036]   Andersson, L., Doolan, P., Feldman, N., Fredette, A., and
               B. Thomas, "LDP Specification", RFC 3036, January 2001.

   [RFC3037]   Thomas, B. and E. Gray, "LDP Applicability", RFC 3037,
               January 2001.

   [RFC3215]   Boscher, C., Cheval, P., Wu, L., and E. Gray, "LDP State
               Machine", RFC 3215, January 2002.

   [RFC3289]   Baker, F., Chan, K., and A. Smith, "Management
               Information Base for the Differentiated Services
               Architecture", RFC 3289, May 2002.

   [RFC3291]   Daniele, M., Haberman, B., Routhier, S., and J.
               Schoenwaelder, "Textual Coventions for Internet Network
               Addresses", RFC 3291, May 2002.

   [RFC3413]   Levi, D., Meyers, P. and B. Stewart, "Simple Network
               Management Protocol (SNMP) Applications", STD 62, RFC
               3413, December 2002.




RFC 3815                      MPLS LDP MIB                     June 2004


   [RFC3811]   Nadeau, T. and J. Cucchiara, Editors  "Definitions of
               Textual Conventions (TCs) for Multiprotocol Label
               Switching (MPLS) Management", RFC 3811, June 2004.

   [RFC3813]   Srinivansan, C., Viswanathan, A., and T. Nadeau,
               "Multiprotocol Label Switching (MPLS) Label Switching
               Router (LSR) Management Information Base (MIB)", RFC
               3813, June 2004

6.2.  Informative References

   [MPLSMGMT]  Nadeau, T., Srinivasan, C., and A. Farrel, "Multiprotocol
               Label Switching (MPLS) Management Overview", Work in
               Progress, September 2003.

   [RFC2684]   Grossman, D. and J. Heinanen, "Multiprotocol
               Encapsulation over ATM Adaptation Layer 5", RFC 2684,
               September 1999.

   [RFC3410]   Case, J., Mundy, R., Partain, D. and B. Stewart,
               "Introduction and Applicability Statements for Internet-
               Standard Management Framework", RFC 3410, December 2002.

7.  Security Considerations

   This Security Considerations section consists of 4 subsections, one
   for each of the MIB Modules in this document.

7.1.  Security Considerations for MPLS-LDP-STD-MIB

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLdpEntityTable contains objects to provision potential
        LDP sessions on the Label Switching Router (LSR) or Label Edge
        Router (LER).   The mplsLdpLspFecTable contains objects which
        associate an LSP with a FEC.  Unauthorized access to objects in
        these tables, could result in disruption of traffic on the
        network.  This is especially true if an LDP session has been
        established.  The use of stronger mechanisms such as SNMPv3
        security should be considered where possible.  Specifically,
        SNMPv3 VACM and USM MUST be used with any v3 agent which
        implements this MIB.  Administrators should consider whether



RFC 3815                      MPLS LDP MIB                     June 2004


        read access to these objects should be allowed, since read
        access may be undesirable under certain circumstances.

   Some of the readable objects in this MIB module i.e., (objects with a
   MAX-ACCESS other than not-accessible), may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLdpEntityTable, mplsLdpPeerTable, mplsLdpSessionTable
        and mplsLdpSessionStatsTable collectively show the LDP LSP
        network topology.  If an Administrator does not want to reveal
        the LDP LSP topology of the network, then these tables should be
        considered sensitive/vulnerable.

7.2.  Security Considerations for MPLS-LDP-ATM-STD-MIB

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLdpEntityAtmTable and mplsLdpEntityAtmLRTable contain
        objects to provision potential LDP sessions on the Label
        Switching Router (LSR) or Label Edge Router (LER) over Layer 2
        of ATM.  These tables extend the mplsLdpEntityTable in the MPLS-
        LDP-MIB.  Unauthorized access to objects in these tables, could
        result in disruption of traffic on the network.  This is
        especially true if an LDP session has been established.  The use
        of stronger mechanisms such as SNMPv3 security should be
        considered where possible.  Specifically, SNMPv3 VACM and USM
        MUST be used with any v3 agent which implements this MIB.
        Administrators should consider whether read access to these
        objects should be allowed, since read access may be undesirable
        under certain circumstances.

   Some of the readable objects in this MIB module i.e., (objects with a
   MAX-ACCESS other than not-accessible), may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:



RFC 3815                      MPLS LDP MIB                     June 2004


   o    the mplsLdpEntityAtmTable and mplsLdpEntityAtmLRTable show the
        Label Ranges for ATM.  If an Administrator does not want to
        reveal this information then these tables should be considered
        sensitive/vulnerable and treated accordingly.

7.3.  Security Considerations for MPLS-LDP-FRAME-RELAY-STD-MIB

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLdpEntityFrameRelayTable and
        mplsLdpEntityFrameRelayLRTable contain objects to provision
        potential LDP sessions on the Label Switching Router (LSR) or
        Label Edge Router (LER) over Layer 2 of Frame Relay.  These
        tables extend the mplsLdpEntityTable in the MPLS-LDP-MIB.
        Unauthorized access to objects in these tables, could result in
        disruption of traffic on the network.  This is especially true
        if an LDP session has been established.  The use of stronger
        mechanisms such as SNMPv3 security should be considered where
        possible.  Specifically, SNMPv3 VACM and USM MUST be used with
        any v3 agent which implements this MIB.  Administrators should
        consider whether read access to these objects should be allowed,
        since read access may be undesirable under certain
        circumstances.

   Some of the readable objects in this MIB module i.e., (objects with a
   MAX-ACCESS other than not-accessible), may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLdpEntityFrameRelayTable and
        mplsLdpEntityFrameRelayLRTable show the Label Ranges for Frame
        Relay.  If an Administrator does not want to reveal this
        information then these tables should be considered
        sensitive/vulnerable and treated accordingly.








RFC 3815                      MPLS LDP MIB                     June 2004


7.4.  Security Considerations for MPLS-LDP-GENERIC-STD-MIB

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLdpEntityGenericLRTable contains objects to provision
        potential LDP sessions on the Label Switching Router (LSR) or
        Label Edge Router (LER) over Layer 2 of Ethernet.  This table
        extends the mplsLdpEntityTable in the MPLS-LDP-MIB.
        Unauthorized access to objects in these tables, could result in
        disruption of traffic on the network.  This is especially true
        if an LDP session has been established.  The use of stronger
        mechanisms such as SNMPv3 security should be considered where
        possible.  Specifically, SNMPv3 VACM and USM MUST be used with
        any v3 agent which implements this MIB.  Administrators should
        consider whether read access to these objects should be allowed,
        since read access may be undesirable under certain
        circumstances.

   Some of the readable objects in this MIB module i.e., (objects with a
   MAX-ACCESS other than not-accessible), may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLdpEntityGenericLRTable shows the Label Ranges for
        ethernet.  If an Administrator does not want to reveal this
        information then these tables should be considered
        sensitive/vulnerable and treated accordingly.

7.5.  Additional Security Considerations

   The following paragraphs describe additional security considerations
   which are applicable to all 4 of the MIB Modules in this document.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the objects
   in this MIB module.




RFC 3815                      MPLS LDP MIB                     June 2004


   It is RECOMMENDED that implementers consider the security features as
   provided by the SNMPv3 framework (see [RFC3410], section 8),
   including full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module, is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

8.  IANA Considerations

   As described in [MPLSMGMT] and as requested in the MPLS-TC-STD-MIB
   [MPLSTCMIB], MPLS related standards track MIB modules should be
   rooted under the mplsStdMIB subtree.  There are 4 MPLS MIB Modules
   contained in this document, each of the following "IANA
   Considerations" subsections lists new IANA assignments under the
   mplsStdMIB subtree.  New assignments can only be made via a Standards
   Action as specified in [RFC2434].

8.1.  IANA Considerations for MPLS-LDP-STD-MIB

   The IANA has assigned { mplsStdMIB 4 } to the MPLS-LDP-STD-MIB module
   specified in this document.

8.2.  IANA Considerations for MPLS-LDP-ATM-STD-MIB

   The IANA has assigned { mplsStdMIB 5 } to the MPLS-LDP-ATM-STD-MIB
   module specified in this document.

8.3.  IANA Considerations for MPLS-LDP-FRAME-RELAY-STD-MIB

   The IANA has assigned { mplsStdMIB 6 } to the MPLS-LDP-FRAME-RELAY-
   STD-MIB module specified in this document.

8.4.  IANA Considerations for MPLS-LDP-GENERIC-STD-MIB

   The IANA has assigned { mplsStdMIB 7 } to the MPLS-LDP-GENERIC-STD-
   MIB module specified in this document.









RFC 3815                      MPLS LDP MIB                     June 2004


9.  Authors' Addresses

   James V. Luciani
   Marconi Communications, Inc.
   900 Chelmsford Street
   Lowell, MA 01851

   EMail: james_luciani@mindspring.com


   Hans Sjostrand
   ipUnplugged
   P.O. Box 101 60
   S-121 28 Stockholm, Sweden

   Phone: +46 8 725 5900
   EMail: hans@ipunplugged.com


   Joan E. Cucchiara
   Marconi Communications, Inc.
   900 Chelmsford Street
   Lowell, MA 01851

   Phone: +1 978 275 7400
   EMail: jcucchiara@mindspring.com

























RFC 3815                      MPLS LDP MIB                     June 2004


10.  Full Copyright Statement

   Copyright (C) The Internet Society (2004).  This document is subject
   to the rights, licenses and restrictions contained in BCP 78, and
   except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at ietf-
   ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.