Rfc5449
TitleOSPF Multipoint Relay (MPR) Extension for Ad Hoc Networks
AuthorE. Baccelli, P. Jacquet, D. Nguyen, T. Clausen
DateFebruary 2009
Format:TXT, HTML
Status:EXPERIMENTAL






Network Working Group                                        E. Baccelli
Request for Comments: 5449                                    P. Jacquet
Category: Experimental                                             INRIA
                                                               D. Nguyen
                                                                     CRC
                                                              T. Clausen
                                                LIX, Ecole Polytechnique
                                                           February 2009


       OSPF Multipoint Relay (MPR) Extension for Ad Hoc Networks

Status of This Memo

   This memo defines an Experimental Protocol for the Internet
   community.  It does not specify an Internet standard of any kind.
   Discussion and suggestions for improvement are requested.
   Distribution of this memo is unlimited.

Copyright Notice

   Copyright (c) 2009 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (http://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.

Abstract

   This document specifies an OSPFv3 interface type tailored for mobile
   ad hoc networks.  This interface type is derived from the broadcast
   interface type, and is denoted the "OSPFv3 MANET interface type".
















RFC 5449              OSPF MPR Extension for MANET         February 2009


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  3
   3.  Applicability Statement  . . . . . . . . . . . . . . . . . . .  5
     3.1.  MANET Characteristics  . . . . . . . . . . . . . . . . . .  5
     3.2.  OSPFv3 MANET Interface Characteristics . . . . . . . . . .  5
   4.  Protocol Overview and Functioning  . . . . . . . . . . . . . .  6
     4.1.  Efficient Flooding Using MPRs  . . . . . . . . . . . . . .  6
     4.2.  MPR Topology-Reduction . . . . . . . . . . . . . . . . . .  6
     4.3.  Multicast Transmissions of Protocol Packets  . . . . . . .  7
     4.4.  MPR Adjacency-Reduction  . . . . . . . . . . . . . . . . .  7
   5.  Protocol Details . . . . . . . . . . . . . . . . . . . . . . .  7
     5.1.  Data Structures  . . . . . . . . . . . . . . . . . . . . .  7
       5.1.1.  N(i): Symmetric 1-Hop Neighbor Set . . . . . . . . . .  7
       5.1.2.  N2(i): Symmetric Strict 2-Hop Neighbor Set . . . . . .  8
       5.1.3.  Flooding-MPR Set . . . . . . . . . . . . . . . . . . .  8
       5.1.4.  Flooding-MPR-Selector Set  . . . . . . . . . . . . . .  9
       5.1.5.  Path-MPR Set . . . . . . . . . . . . . . . . . . . . .  9
       5.1.6.  Path-MPR-Selector Set  . . . . . . . . . . . . . . . . 10
       5.1.7.  MPR Set  . . . . . . . . . . . . . . . . . . . . . . . 10
       5.1.8.  MPR-Selector Set . . . . . . . . . . . . . . . . . . . 10
     5.2.  Hello Protocol . . . . . . . . . . . . . . . . . . . . . . 10
       5.2.1.  Flooding-MPR Selection . . . . . . . . . . . . . . . . 11
       5.2.2.  Flooding-MPR Selection Signaling - FMPR TLV  . . . . . 11
       5.2.3.  Neighbor Ordering  . . . . . . . . . . . . . . . . . . 12
       5.2.4.  Metric Signaling - METRIC-MPR TLV and PMPR TLV . . . . 12
       5.2.5.  Path-MPR Selection . . . . . . . . . . . . . . . . . . 12
       5.2.6.  Path-MPR Selection Signaling - PMPR TLV  . . . . . . . 12
       5.2.7.  Hello Packet Processing  . . . . . . . . . . . . . . . 13
     5.3.  Adjacencies  . . . . . . . . . . . . . . . . . . . . . . . 13
       5.3.1.  Packets over 2-Way Links . . . . . . . . . . . . . . . 14
       5.3.2.  Adjacency Conservation . . . . . . . . . . . . . . . . 14
     5.4.  Link State Advertisements  . . . . . . . . . . . . . . . . 14
       5.4.1.  LSA Flooding . . . . . . . . . . . . . . . . . . . . . 15
       5.4.2.  Link State Acknowledgments . . . . . . . . . . . . . . 17
     5.5.  Hybrid Routers . . . . . . . . . . . . . . . . . . . . . . 18
     5.6.  Synch Routers  . . . . . . . . . . . . . . . . . . . . . . 18
     5.7.  Routing Table Computation  . . . . . . . . . . . . . . . . 18
   6.  Packet Formats . . . . . . . . . . . . . . . . . . . . . . . . 19
     6.1.  Flooding-MPR  TLV  . . . . . . . . . . . . . . . . . . . . 19
     6.2.  Metric-MPR TLV . . . . . . . . . . . . . . . . . . . . . . 19
     6.3.  Path-MPR TLV . . . . . . . . . . . . . . . . . . . . . . . 22
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . . 24
   8.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 25
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 26
     9.1.  Normative References . . . . . . . . . . . . . . . . . . . 26
     9.2.  Informative References . . . . . . . . . . . . . . . . . . 26



RFC 5449              OSPF MPR Extension for MANET         February 2009


   Appendix A.  Flooding-MPR Selection Heuristic  . . . . . . . . . . 28
   Appendix B.  Path-MPR Selection Heuristic  . . . . . . . . . . . . 29
   Appendix C.  Contributors  . . . . . . . . . . . . . . . . . . . . 30
   Appendix D.  Acknowledgments . . . . . . . . . . . . . . . . . . . 30

1.  Introduction

   This document specifies an extension of OSPFv3 [RFC5340] that is
   adapted to mobile ad hoc networks (MANETs) [RFC2501] and based on
   mechanisms providing:

   Flooding-reduction:  only a subset of all routers will be involved in
      (re)transmissions during a flooding operation.

   Topology-reduction:  only a subset of links are advertised, hence
      both the number and the size of Link State Advertisements (LSAs)
      are decreased.

   Adjacency-reduction:  adjacencies are brought up only with a subset
      of neighbors for lower database synchronization overhead.

   These mechanisms are based on multipoint relays (MPR), a technique
   developed in the Optimized Link State Routing Protocol (OLSR)
   [RFC3626].

   The extension specified in this document integrates into the OSPF
   framework by defining the OSPFv3 MANET interface type.  While this
   extension enables OSPFv3 to function efficiently on mobile ad hoc
   networks, operation of OSPFv3 on other types of interfaces or
   networks, or in areas without OSPFv3 MANET interfaces, remains
   unaltered.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   [RFC2119].

   This document uses OSPF terminology as defined in [RFC2328] and
   [RFC5340], and Link-Local Signaling (LLS) terminology as defined in
   [RFC4813]; it introduces the following terminology to the OSPF
   nomenclature:

   OSPFv3 MANET interface  - the OSPFv3 interface type for MANETs, as
      specified in this document.





RFC 5449              OSPF MPR Extension for MANET         February 2009


   Additionally, the following terms are used in this document:

   MANET router -  a router that has only OSPFv3 MANET interfaces.

   Wired router -  a router that has only OSPFv3 interface of types
      other than OSPFv3 MANET interfaces.

   Hybrid router -  a router that has OSPFv3 interfaces of several
      types, including at least one of the OSPFv3 MANET interface type.

   Neighbor -  a router, reachable through an OSPFv3 interface (of any
      type).

   MANET neighbor -  a neighbor, reachable through an OSPFv3 MANET
      interface.

   Symmetric 1-hop neighbor -  a neighbor, in a state greater than or
      equal to 2-Way (through an interface of any type).

   Symmetric strict 2-hop neighbor -  a symmetric 1-hop neighbor of a
      symmetric 1-hop neighbor, which is not itself a symmetric 1-hop
      neighbor of the considered router.

   Symmetric strict 2-hop neighborhood -  the set formed by all the
      symmetric strict 2-hop neighbors of the considered router.

   Synch router -  a router that brings up adjacencies with all of its
      MANET neighbors.

   Flooding-MPR -  a router that is selected by its symmetric 1-hop
      neighbor, router X, to retransmit all broadcast protocol packets
      that it receives from router X, provided that the broadcast
      protocol packet is not a duplicate and that the Hop Limit field of
      the protocol packet is greater than one.

   Path-MPR -  a router that is selected by a symmetric 1-hop neighbor,
      X, as being on the shortest path from a router in the symmetric
      strict 2-hop neighborhood of router X to router X.

   Multipoint relay (MPR) -  a router that is selected by its symmetric
      1-hop neighbor as either a Flooding-MPR, a Path-MPR, or both.

   Flooding-MPR-selector -  a router that has selected its symmetric
      1-hop neighbor, router X, as one of its Flooding-MPRs is a
      Flooding-MPR-selector of router X.






RFC 5449              OSPF MPR Extension for MANET         February 2009


   Path-MPR-selector -  a router that has selected its symmetric 1-hop
      neighbor, router X, as one of its Path-MPRs is a Path-MPR selector
      of router X.

   MPR-selector -  a router that has selected its symmetric 1-hop
      neighbor, router X, as either one of its Flooding-MPRs, one of its
      Path-MPRs, or both is an MPR-selector of router X.

3.  Applicability Statement

   The OSPFv3 MANET interface type, defined in this specification,
   allows OSPFv3 to be deployed within an area where parts of that area
   are a mobile ad hoc network (MANET) with moderate mobility
   properties.

3.1.  MANET Characteristics

   MANETs [RFC2501] are networks in which a dynamic network topology is
   a frequently expected condition, often due to router mobility and/or
   to varying quality of wireless links -- the latter of which also
   generally entails bandwidth scarcity and interference issues between
   neighbors.

   Moreover, MANETs often exhibit "semi-broadcast" properties, i.e., a
   router R that makes a transmission within a MANET can only assume
   that transmission to be received by a subset of the total number of
   routers within that MANET.  Further, if two routers, R1 and R2, each
   make a transmission, neither of these transmissions is guaranteed to
   be received by the same subset of routers within the MANET -- even if
   R1 and R2 can mutually receive transmissions from each other.

   These characteristics are incompatible with several OSPFv3
   mechanisms, including, but not limited to, existing mechanisms for
   control-traffic reduction, such as flooding-reduction, topology-
   reduction, and adjacency-reduction (e.g., Designated Router).

3.2.  OSPFv3 MANET Interface Characteristics

   An interface of the OSPFv3 MANET interface type is the point of
   attachment of an OSPFv3 router to a network that may have MANET
   characteristics.  That is, an interface of the OSPFv3 MANET interface
   type is able to accommodate the MANET characteristics described in
   Section 3.1.  An OSPFv3 MANET interface type is not prescribing a set
   of behaviors or expectations that the network is required to satisfy.
   Rather, it is describing operating conditions under which protocols
   on an interface towards that network must be able to function (i.e.,
   the protocols are required to be able to operate correctly when faced
   with the characteristics described in Section 3.1).  As such, the



RFC 5449              OSPF MPR Extension for MANET         February 2009


   OSPFv3 MANET interface type is a generalization of other OSPFv3
   interface types; for example, a protocol operating correctly over an
   OSPFv3 MANET interface would also operate correctly over an OSPFv3
   broadcast interface (whereas the inverse would not necessarily be
   true).

   Efficient OSPFv3 operation over MANETs relies on control-traffic
   reduction and on using mechanisms appropriate for semi-broadcast.
   The OSPFv3 MANET interface type, defined in this document, allows
   networks with MANET characteristics into the OSPFv3 framework by
   integrating mechanisms (flooding-reduction, topology-reduction, and
   adjacency-reduction) derived from solutions standardized by the MANET
   working group.

4.  Protocol Overview and Functioning

   The OSPFv3 MANET interface type, defined in this specification, makes
   use of flooding-reduction, topology-reduction, and adjacency-
   reduction, all based on MPR, a technique derived from [RFC3626], as
   standardized in the MANET working group.  Multicast transmissions of
   protocol packets are used when possible.

4.1.  Efficient Flooding Using MPRs

   OSPFv3 MANET interfaces use a flooding-reduction mechanism, denoted
   MPR flooding [MPR], whereby only a subset of MANET neighbors (those
   selected as Flooding-MPR) participate in a flooding operation.  This
   reduces the number of (re)transmissions necessary for a flooding
   operation [MPR-analysis], while retaining resilience against
   transmission errors (inherent when using wireless links) and against
   obsolete two-hop neighbor information (e.g., as caused by router
   mobility) [MPR-robustness].

4.2.  MPR Topology-Reduction

   OSPFv3 MANET interfaces use a topology-reduction mechanism, denoted
   MPR topology-reduction, whereby only necessary links to MANET
   neighbors (those identified by Path-MPR selection as belonging to
   shortest paths) are included in LSAs.  Routers in a MANET
   periodically generate and flood Router-LSAs describing their
   selection of such links to their Path-MPRs.  Such links are reported
   as point-to-point links.  This reduces the size of LSAs originated by
   routers on a MANET [MPR-topology], while retaining classic OSPF
   properties: optimal paths using synchronized adjacencies (if
   synchronized paths are preferred over non-synchronized paths of equal
   cost).





RFC 5449              OSPF MPR Extension for MANET         February 2009


4.3.  Multicast Transmissions of Protocol Packets

   OSPFv3 MANET interfaces employ multicast transmissions when possible,
   thereby taking advantage of inherent broadcast capabilities of the
   medium, if present (with wireless interfaces, this can often be the
   case [RFC2501]).  In particular, LSA acknowledgments are sent via
   multicast over these interfaces, and retransmissions over the same
   interfaces are considered as implicit acknowledgments.  Jitter
   management, such as delaying packet (re)transmission, can be employed
   in order to allow several packets to be bundled into a single
   transmission, which may avoid superfluous retransmissions due to
   packet collisions [RFC5148].

4.4.  MPR Adjacency-Reduction

   Adjacencies over OSPFv3 MANET interfaces are required to be formed
   only with a subset of the neighbors of that OSPFv3 MANET interface.
   No Designated Router or Backup Designated Router are elected on an
   OSPFv3 MANET interface.  Rather, adjacencies are brought up over an
   OSPFv3 MANET interface only with MPRs and MPR selectors.  Only a
   small subset of routers in the MANET (called Synch routers) are
   required to bring up adjacencies with all their MANET neighbors.
   This reduces the amount of control traffic needed for database
   synchronization, while ensuring that LSAs still describe only
   synchronized adjacencies.

5.  Protocol Details

   This section complements [RFC5340] and specifies the information that
   must be maintained, processed, and transmitted by routers that
   operate one or more OSPFv3 MANET interfaces.

5.1.  Data Structures

   In addition to the values used in [RFC5340], the Type field in the
   interface data structure can take a new value, "MANET".  Furthermore,
   and in addition to the protocol structures defined by [RFC5340],
   routers that operate one or more MANET interfaces make use of the
   data structures described below.

5.1.1.  N(i): Symmetric 1-Hop Neighbor Set

   The Symmetric 1-hop Neighbor set N(i) records router IDs of the set
   of symmetric 1-hop neighbors of the router on interface i.  More
   precisely, N(i) records tuples of the form:






RFC 5449              OSPF MPR Extension for MANET         February 2009


                   (1_HOP_SYM_id, 1_HOP_SYM_time)

   where:

   1_HOP_SYM_id:  is the router ID of the symmetric 1-hop neighbor of
      this router over interface i.

   1_HOP_SYM_time:  specifies the time at which the tuple expires and
      MUST be removed from the set.

   For convenience throughout this document, N will denote the union of
   all N(i) sets for all MANET interfaces on the router.

5.1.2.  N2(i): Symmetric Strict 2-Hop Neighbor Set

   The Symmetric strict 2-hop Neighbor set N2(i) records links between
   routers in N(i) and their symmetric 1-hop neighbors, excluding:

   (i)    the router performing the computation, and

   (ii)   all routers in N(i).

   More precisely, N2(i) records tuples of the form:

               (2_HOP_SYM_id, 1_HOP_SYM_id, 2_HOP_SYM_time)

   where:

   2_HOP_SYM_id:  is the router ID of a symmetric strict 2-hop neighbor.

   1_HOP_SYM_id:  is the router ID of the symmetric 1-hop neighbor of
      this router through which the symmetric strict 2-hop neighbor can
      be reached.

   2_HOP_SYM_time:  specifies the time at which the tuple expires and
      MUST be removed from the set.

   For convenience throughout this document, N2 will denote the union of
   all N2(i) sets for all MANET interfaces on the router.

5.1.3.  Flooding-MPR Set

   The Flooding-MPR set on interface i records router IDs of a subset of
   the routers listed in N(i), selected such that, through this subset,
   each router listed in N2(i) is reachable in 2 hops by this router.
   There is one Flooding-MPR set per MANET interface.  More precisely,
   the Flooding-MPR set records tuples of the form:




RFC 5449              OSPF MPR Extension for MANET         February 2009


                    (Flooding_MPR_id, Flooding_MPR_time)

   where:

   Flooding_MPR_id:  is the router ID of the symmetric 1-hop neighbor of
      this router that is selected as Flooding-MPR.

   Flooding_MPR_time:  specifies the time at which the tuple expires and
      MUST be removed from the set.

   Flooding-MPR selection is detailed in Section 5.2.1.

5.1.4.  Flooding-MPR-Selector Set

   The Flooding-MPR-selector set on interface i records router IDs of
   the set of symmetric 1-hop neighbors of this router on interface i
   that have selected this router as their Flooding-MPR.  There is one
   Flooding-MPR-selector set per MANET interface.  More precisely, the
   Flooding-MPR-selector set records tuples of the form:

          (Flooding_MPR_SELECTOR_id, Flooding_MPR_SELECTOR_time)

   where:

   Flooding_MPR_SELECTOR_id:  is the router ID of the symmetric 1-hop
      neighbor of this router, that has selected this router as its
      Flooding-MPR.

   Flooding_MPR_SELECTOR_time:  specifies the time at which the tuple
      expires and MUST be removed from the set.

   Flooding-MPR selection is detailed in Section 5.2.1.

5.1.5.  Path-MPR Set

   The Path-MPR set records router IDs of routers in N that provide
   shortest paths from routers in N2 to this router.  There is one Path-
   MPR set per router.  More precisely, the Path-MPR set records tuples
   of the form:

                     (Path_MPR_id, Path_MPR_time)

   where:

   Path_MPR_id:  is the router ID of the symmetric 1-hop neighbor of
      this router, selected as Path-MPR.





RFC 5449              OSPF MPR Extension for MANET         February 2009


   Path_MPR_time:  specifies the time at which the tuple expires and
      MUST be removed from the set.

   Path-MPR selection is detailed in Section 5.2.5.

5.1.6.  Path-MPR-Selector Set

   The Path-MPR-selector set records router IDs of the set of symmetric
   1-hop neighbors over any MANET interface that have selected this
   router as their Path-MPR.  There is one Path-MPR-selector set per
   router.  More precisely, the Path-MPR-selector set records tuples of
   the form:

          (Path_MPR_SELECTOR_id, Path_MPR_SELECTOR_time)

   where:

   Path_MPR_SELECTOR_id:  is the router ID of the symmetric 1-hop
      neighbor of this router that has selected this router as its Path-
      MPR.

   Path_MPR_SELECTOR_time:  specifies the time at which the tuple
      expires and MUST be removed from the set.

   Path-MPR selection is detailed in Section 5.2.5.

5.1.7.  MPR Set

   The MPR set is the union of the Flooding-MPR set(s) and the Path-MPR
   set.  There is one MPR set per router.

5.1.8.  MPR-Selector Set

   The MPR-selector set is the union of the Flooding-MPR-selector set(s)
   and the Path-MPR-selector set.  There is one MPR-selector set per
   router.

5.2.  Hello Protocol

   On OSPFv3 MANET interfaces, packets are sent, received, and processed
   as defined in [RFC5340] and [RFC2328], and augmented for MPR
   selection as detailed in this section.

   All additional signaling for OSPFv3 MANET interfaces is done through
   inclusion of TLVs within an LLS block [RFC4813], which is appended to
   Hello packets.  If an LLS block is not already present, an LLS block
   MUST be created and appended to the Hello packets.




RFC 5449              OSPF MPR Extension for MANET         February 2009


   Hello packets sent over an OSPFv3 MANET interface MUST have the L bit
   of the OSPF Options field set, as per [RFC4813], indicating the
   presence of an LLS block.

   This document defines and employs the following TLVs in Hello packets
   sent over OSPFv3 MANET interfaces:

   FMPR -  signaling Flooding-MPR selection;

   PMPR -  signaling Path-MPR selection;

   METRIC-MPR -  signaling metrics.

   The layout and internal structure of these TLVs is detailed in
   Section 6.

5.2.1.  Flooding-MPR Selection

   The objective of Flooding-MPR selection is for a router to select a
   subset of its neighbors such that a packet, retransmitted by these
   selected neighbors, will be received by all routers 2 hops away.
   This property is called the Flooding-MPR "coverage criterion".  The
   Flooding-MPR set of a router is computed such that, for each OSPFv3
   MANET interface, it satisfies this criterion.  The information
   required to perform this calculation (i.e., link sensing and
   neighborhood information) is acquired through periodic exchange of
   OSPFv3 Hello packets.

   Flooding-MPRs are computed by each router that operates at least one
   OSPFv3 MANET interface.  The smaller the Flooding-MPR set is, the
   lower the overhead will be.  However, while it is not essential that
   the Flooding-MPR set is minimal, the "coverage criterion" MUST be
   satisfied by the selected Flooding-MPR set.

   The willingness of a neighbor router to act as Flooding-MPR MAY be
   taken into consideration by a heuristic for Flooding-MPR selection.
   An example heuristic that takes willingness into account is given in
   Appendix A.

5.2.2.  Flooding-MPR Selection Signaling - FMPR TLV

   A router MUST signal its Flooding-MPRs set to its neighbors by
   including an FMPR TLV in generated Hello packets.  Inclusion of this
   FMPR TLV signals the list of symmetric 1-hop neighbors that the
   sending router has selected as Flooding-MPRs, as well as the
   willingness of the sending router to be elected Flooding-MPR by other
   routers.  The FMPR TLV structure is detailed in Section 6.1.




RFC 5449              OSPF MPR Extension for MANET         February 2009


5.2.3.  Neighbor Ordering

   Neighbors listed in the Hello packets sent over OSPFv3 MANET
   interfaces MUST be included in the order as given below:

   1.  symmetric 1-hop neighbors that are selected as Flooding-MPRs;

   2.  other symmetric 1-hop neighbors;

   3.  other 1-hop neighbors.

   This ordering allows correct interpretation of an included FMPR TLV.

5.2.4.  Metric Signaling - METRIC-MPR TLV and PMPR TLV

   Hello packets sent over OSPFv3 MANET interfaces MUST advertise the
   costs of links towards ALL the symmetric MANET neighbors of the
   sending router.  If the sending router has more than one OSPFv3 MANET
   interface, links to ALL the symmetric MANET neighbors over ALL the
   OSPFv3 MANET interfaces of that router MUST have their costs
   advertised.

   The costs of the links between the router and each of its MANET
   neighbors on the OSPFv3 MANET interface over which the Hello packet
   is sent MUST be signaled by including METRIC-MPR TLVs.  The METRIC-
   MPR TLV structure is detailed in Section 6.2.

   Moreover, the lowest cost from each MANET neighbor towards the router
   (regardless of over which interface) MUST be specified in the
   included PMPR TLV.  Note that the lowest cost can be over an
   interface that is not an OSPFv3 MANET interface.

5.2.5.  Path-MPR Selection

   A router that has one or more OSPFv3 MANET interfaces MUST select a
   Path-MPR set from among routers in N.  Routers in the Path-MPR set of
   a router are those that take part in the shortest (with respect to
   the metrics used) path from routers in N2 to this router.  A
   heuristic for Path-MPR selection is given in Appendix B.

5.2.6.  Path-MPR Selection Signaling - PMPR TLV

   A router MUST signal its Path-MPR set to its neighbors by including a
   PMPR TLV in generated Hello packets.

   A PMPR TLV MUST contain a list of IDs of all symmetric 1-hop
   neighbors of all OSPFv3 MANET interfaces of the router.  These IDs
   MUST be included in the PMPR TLV in the order as given below:



RFC 5449              OSPF MPR Extension for MANET         February 2009


   1.  Neighbors that are both adjacent AND selected as Path-MPR for any
       OSPFv3 MANET interface of the router generating the Hello packet.

   2.  Neighbors that are adjacent over any OSPFv3 MANET interface of
       the router generating the Hello packet.

   3.  Symmetric 1-hop neighbors on any OSPFv3 MANET interface of the
       router generating the Hello packet that have not been previously
       included in this PMPR TLV.

   The list of neighbor IDs is followed by a list of costs for the links
   from these neighbors to the router generating the Hello packet
   containing this PMPR TLV, as detailed in Section 5.2.4.  The PMPR TLV
   structure is detailed in Section 6.3.

5.2.7.  Hello Packet Processing

   In addition to the processing specified in [RFC5340], N and N2 MUST
   be updated when received Hello packets indicate changes to the
   neighborhood of an OSPFv3 MANET interface i.  In particular, if a
   received Hello packet signals that a tuple in N (or N2) is to be
   deleted, the deletion is done immediately, without waiting for the
   tuple to expire.  Note that N2 records not only 2-hop neighbors
   listed in received Hellos but also 2-hop neighbors listed in the
   appended PMPR TLVs.

   The Flooding-MPR set MUST be recomputed when either of N(i) or N2(i)
   has changed.  The Path-MPR set MUST be recomputed when either of N or
   N2 has changed.  Moreover, the Path-MPR set MUST be recomputed if
   appended LLS information signals change with respect to one or more
   link costs.

   The Flooding-MPR-selector set and the Path-MPR-selector set MUST be
   updated upon receipt of a Hello packet containing LLS information
   indicating changes in the list of neighbors that has selected the
   router as MPR.

   If a Hello with the S bit set is received on an OSPFv3 MANET
   interface of a router, from a non-adjacent neighbor, the router MUST
   transition this neighbor's state to ExStart.

5.3.  Adjacencies

   Adjacencies are brought up between OSPFv3 MANET interfaces as
   described in [RFC5340] and [RFC2328].  However, in order to reduce
   the control-traffic overhead over the OSPFv3 MANET interfaces, a
   router that has one or more such OSPFv3 MANET interfaces MAY bring up
   adjacencies with only a subset of its MANET neighbors.



RFC 5449              OSPF MPR Extension for MANET         February 2009


   Over an OSPFv3 MANET interface, a router MUST bring up adjacencies
   with all MANET neighbors that are included in its MPR set and its
   MPR-selector set; this ensures that, beyond the first hop, routes use
   synchronized links (if synchronized paths are preferred over non-
   synchronized paths of equal cost).  A router MAY bring up adjacencies
   with other MANET neighbors, at the expense of additional
   synchronization overhead.

5.3.1.  Packets over 2-Way Links

   When a router does not form a full adjacency with a MANET neighbor,
   the state of that neighbor does not progress beyond 2-Way (as defined
   in [RFC2328]).  A router can send protocol packets, such as LSAs, to
   a MANET neighbor in 2-Way state.  Therefore, any packet received from
   a symmetric MANET neighbor MUST be processed.

   As with the OSPF broadcast interface [RFC2328], the next hop in the
   forwarding table MAY be a neighbor that is not adjacent.  However,
   when a data packet has travelled beyond its first hop, the MPR-
   selection process guarantees that subsequent hops in the shortest
   path tree (SPT) will be over adjacencies (if synchronized paths are
   preferred over non-synchronized paths of equal cost).

5.3.2.  Adjacency Conservation

   Adjacencies are torn down according to [RFC2328].  When the MPR set
   or MPR-selector set is updated (due to changes in the neighborhood),
   and when a neighbor was formerly, but is no longer, in the MPR set or
   the MPR-selector set, then the adjacency with that neighbor is kept
   unless the change causes the neighbor to cease being a symmetric
   1-hop neighbor.

   When a router receives Hello packets from a symmetric 1-hop neighbor
   that ceases to list this router as being adjacent (see
   Section 5.2.6), the state of that neighbor MUST be changed to:

   1.  2-Way if the neighbor is not in the MPR set or MPR-selector set,
       or

   2.  ExStart if either the neighbor is in the MPR set or MPR-selector
       set, or the neighbor or the router itself is a Synch router.

5.4.  Link State Advertisements

   Routers generate Router-LSAs periodically, using the format specified
   in [RFC5340] and [RFC2328].





RFC 5449              OSPF MPR Extension for MANET         February 2009


   Routers that have one or more OSPFv3 MANET interfaces MUST include
   the following links in the Router-LSAs that they generate:

   o  links to all neighbors that are in the Path-MPR set, AND

   o  links to all neighbors that are in the Path-MPR-selector set.

   Routers that have one or more OSPFv3 MANET interfaces MAY list other
   links they have through those OSPFv3 MANET interfaces, at the expense
   of larger LSAs.

   In addition, routers that have one or more OSPFv3 MANET interfaces
   MUST generate updated Router-LSAs when either of the following
   occurs:

   o  a new adjacency has been brought up, reflecting a change in the
      Path-MPR set;

   o  a new adjacency has been brought up, reflecting a change in the
      Path-MPR-selector set;

   o  a formerly adjacent and advertised neighbor ceases to be adjacent;

   o  the cost of a link to (or from) an advertised neighbor has
      changed.

5.4.1.  LSA Flooding

   An originated LSA is flooded, according to [RFC5340], out all
   interfaces concerned by the scope of this LSA.

   Link State Updates received on an interface of a type other than
   OSPFv3 MANET interface are processed and flooded according to
   [RFC2328] and [RFC5340], over every interface.  If a Link State
   Update was received on an OSPFv3 MANET interface, it is processed as
   follows:

   1.  Consistency checks are performed on the received packet according
       to [RFC2328] and [RFC5340], and the Link State Update packet is
       thus associated with a particular neighbor and a particular area.

   2.  If the Link State Update was received from a router other than a
       symmetric 1-hop neighbor, the Link State Update MUST be discarded
       without further processing.

   3.  Otherwise, for each LSA contained in Link State Updates received
       over an OSPFv3 MANET interface, the following steps replace steps
       1 to 5 of Section 13.3 of [RFC2328].



RFC 5449              OSPF MPR Extension for MANET         February 2009


       (1)  If an LSA exists in the Link State Database, with the same
            Link State ID, LS Type, and Advertising Router values as the
            received LSA, and if the received LSA is not newer (see
            Section 13.1 of [RFC2328]), then the received LSA MUST NOT
            be processed, except for acknowledgment as described in
            Section 5.4.2.

       (2)  Otherwise, the LSA MUST be attributed a scope according to
            its type, as specified in Section 3.5 of [RFC5340].

       (3)  If the scope of the LSA is link local or reserved, the LSA
            MUST NOT be flooded on any interface.

       (4)  Otherwise:

            +  If the scope of the LSA is the area, the LSA MUST be
               flooded on all the OSPFv3 interfaces of the router in
               that area, according to the default flooding algorithm
               described in Section 5.4.1.1.

            +  Otherwise, the LSA MUST be flooded on all the OSPFv3
               interfaces of the router according to the default
               flooding algorithm described in Section 5.4.1.1.

5.4.1.1.  Default LSA Flooding Algorithm

   The default LSA flooding algorithm is as follows:

   1.  The LSA MUST be installed in the Link State Database.

   2.  The Age of the LSA MUST be increased by InfTransDelay.

   3.  The LSA MUST be retransmitted over all OSPFv3 interfaces of types
       other than OSPFv3 MANET interface.

   4.  If the sending OSPFv3 interface is a Flooding-MPR-selector of
       this router, then the LSA MUST also be retransmitted over all
       OSPFv3 MANET interfaces concerned by the scope, with the
       multicast address all_SPF_Routers.

   Note that MinLSArrival SHOULD be set to a value that is appropriate
   to dynamic topologies: LSA updating may need to be more frequent in
   MANET parts of an OSPF network than in other parts of an OSPF
   network.







RFC 5449              OSPF MPR Extension for MANET         February 2009


5.4.2.  Link State Acknowledgments

   When a router receives an LSA over an OSPFv3 MANET interface, the
   router MUST proceed to acknowledge the LSA as follows:

   1.  If the LSA was not received from an adjacent neighbor, the router
       MUST NOT acknowledge it.

   2.  Otherwise, if the LSA was received from an adjacent neighbor and
       if the LSA is already in the Link State Database (i.e., the LSA
       has already been received and processed), then the router MUST
       send an acknowledgment for this LSA on all OSPFv3 MANET
       interfaces to the multicast address all_SPF_Routers.

   3.  Otherwise, if the LSA is not already in the Link State Database:

       1.  If the router decides to retransmit the LSA (as part of the
           flooding procedure), the router MUST NOT acknowledge it, as
           this retransmission will be considered as an implicit
           acknowledgment.

       2.  Otherwise, if the router decides to not retransmit the LSA
           (as part of the flooding procedure), the router MUST send an
           explicit acknowledgment for this LSA on all OSPFv3 MANET
           interfaces to the multicast address all_SPF_Routers.

   If a router sends an LSA on an OSPFv3 MANET interface, it expects
   acknowledgments (explicit or implicit) from all adjacent neighbors.
   In the case where the router did not generate, but simply relays, the
   LSA, then the router MUST expect acknowledgments (explicit or
   implicit) only from adjacent neighbors that have not previously
   acknowledged this LSA.  If a router detects that some adjacent
   neighbor has not acknowledged the LSA, then that router MUST
   retransmit the LSA.

   If, due to the MPR flooding-reduction mechanism employed for LSA
   flooding as described in Section 5.4.1, a router decides to not relay
   an LSA, the router MUST still expect acknowledgments of this LSA
   (explicit or implicit) from adjacent neighbors that have not
   previously acknowledged this LSA.  If a router detects that some
   adjacent neighbor has not acknowledged the LSA, then the router MUST
   retransmit the LSA.

   Note that it may be beneficial to aggregate several acknowledgments
   in the same transmission, taking advantage of native multicasting (if
   available).  A timer wait MAY thus be used before any acknowledgment
   transmission.




RFC 5449              OSPF MPR Extension for MANET         February 2009


   Additionally, jitter [RFC5148] on packet (re)transmission MAY be used
   in order to increase the opportunities to bundle several packets
   together in each transmission.

5.5.  Hybrid Routers

   In addition to the operations described in Section 5.2, Section 5.3
   and Section 5.4, Hybrid routers MUST:

   o  select ALL their MANET neighbors as Path-MPRs.

   o  list adjacencies over OSPFv3 interfaces of types other than OSPFv3
      MANET interface, as specified in [RFC5340] and [RFC2328], in
      generated Router-LSAs.

5.6.  Synch Routers

   In a network with no Hybrid routers, at least one Synch router MUST
   be selected.  A Synch router MUST:

   o  set the S bit in the PMPR TLV appended to the Hello packets it
      generates, AND

   o  become adjacent with ALL MANET neighbors.

   A proposed heuristic for selection of Sync routers is as follows:

   o  A router that has a MANET interface and an ID that is higher than
      the ID of all of its current neighbors, and whose ID is higher
      than any other ID present in Router-LSAs currently in its Link
      State Database selects itself as Synch router.

   Other heuristics are possible; however, any heuristic for selecting
   Synch routers MUST ensure the presence of at least one Synch or
   Hybrid router in the network.

5.7.  Routing Table Computation

   When routing table (re)computation occurs, in addition to the
   processing of the Link State Database defined in [RFC5340] and
   [RFC2328], routers that have one or more MANET interfaces MUST take
   into account links between themselves and MANET neighbors that are in
   state 2-Way or higher (as data and protocol packets may be sent,
   received, and processed over these links too).  Thus, the
   connectivity matrix used to compute routes MUST reflect links between
   the root and all its neighbors in state 2-Way and higher, as well as
   links described in the Link State Database.




RFC 5449              OSPF MPR Extension for MANET         February 2009


6.  Packet Formats

   OSPFv3 packets are as defined by [RFC5340] and [RFC2328].  Additional
   LLS signaling [RFC4813] is used in Hello packets sent over OSPFv3
   MANET interfaces, as detailed in this section.

   This specification uses network byte order (most significant octet
   first) for all fields.

6.1.  Flooding-MPR TLV

   A TLV of Type FMPR is defined for signaling Flooding-MPR selection,
   shown in Figure 1.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            Type=FMPR          |           Length              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Willingness  | # Sym. Neigh. |  # Flood MPR  |    Reserved   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 1: Flooding-MPR TLV (FMPR)

   where:

   Willingness -  is an 8-bit unsigned integer field that specifies the
      willingness of the router to flood link-state information on
      behalf of other routers.  It can be set to any integer value from
      1 to 6.  By default, a router SHOULD advertise a willingness of
      WILL_DEFAULT = 3.

   # Sym.  Neigh. -  is an 8-bit unsigned integer field that specifies
      the number of symmetric 1-hop neighbors.  These symmetric 1-hop
      neighbors are listed first among the neighbors in a Hello packet.

   # Flood MPR -  is an 8-bit unsigned integer field that specifies the
      number of neighbors selected as Flooding-MPR.  These Flooding-MPRs
      are listed first among the symmetric 1-hop neighbors.

   Reserved -  is an 8-bit field that SHOULD be cleared ('0') on
      transmission and SHOULD be ignored on reception.

6.2.  Metric-MPR TLV

   A TLV of Type METRIC-MPR is defined for signaling costs of links to
   neighbors, shown in Figure 2.




RFC 5449              OSPF MPR Extension for MANET         February 2009


     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |        Type=METRIC-MPR        |           Length              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Reserved          |U|R|           Cost 0              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |           Cost 1              |           Cost 2              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    :                                                               :
    :                                                               :
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |           Cost n              |            Padding            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 2: Metric TLV (METRIC-MPR)

   where:

   Reserved -  is a 14-bit field that SHOULD be cleared ('0') on
      transmission and SHOULD be ignored on reception.

   R -  is a binary flag, cleared ('0') if the costs advertised in the
      TLV are direct (i.e., the costs of the links from the router to
      the neighbors), or set ('1') if the costs advertised are reverse
      (i.e., the costs of the links from the neighbors to the router).
      By default, R is cleared ('0').

   U -  is a binary flag, cleared ('0') if the cost for each link from
      the sending router and to each advertised neighbor is explicitly
      included (shown in Figure 3), or set ('1') if a single metric
      value is included that applies to all links (shown in Figure 4).

   Cost n -  is an 8-bit unsigned integer field that specifies the cost
      of the link, in the direction specified by the R flag, between
      this router and the neighbor listed at the n-th position in the
      Hello packet when counting from the beginning of the Hello packet
      and with the first neighbor being at position 0.

   Padding -  is a 16-bit field that SHOULD be cleared ('0') on
      transmission and SHOULD be ignored on reception.  Padding is
      included in order that the TLV is 32-bit aligned.  Padding MUST be
      included when the TLV contains an even number of Cost fields and
      MUST NOT be included otherwise.







RFC 5449              OSPF MPR Extension for MANET         February 2009


     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |        Type=METRIC-MPR        |           Length              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Reserved          |0|R|           Cost 0              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |           Cost 1              |           Cost 2              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Figure 3: Metric Advertisement TLV (METRIC-MPR) example with explicit
    individual link costs (U=0) and an odd number of Costs (and, hence,
                               no padding).

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |        Type=METRIC-MPR        |           Length              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Reserved          |1|R|           Cost                |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Figure 4: Metric Advertisement TLV (METRIC-MPR) example with a single
           and uniform link cost (U=1) (and, hence, no padding).



























RFC 5449              OSPF MPR Extension for MANET         February 2009


6.3.  Path-MPR TLV

   A TLV of Type PMPR is defined for signaling Path-MPR selection, shown
   in Figure 1, as well as the link cost associated with these Path-
   MPRs.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            Type=PMPR          |           Length              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  # Sym Neigh  |  # Adj. Neigh |   # Path-MPR  | Reserved  |U|S|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Neighbor ID                         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Neighbor ID                         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    :                                                               :
    :                                                               :
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Cost 0            |            Cost 1             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    :                                                               :
    :                                                               :
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Cost n            |            Padding            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 5: Path-MPR TLV (PMPR)

   # Sym Neigh. -  is an 8-bit unsigned integer field that specifies the
      number of symmetric 1-hop MANET neighbors of all OSPFv3 MANET
      interfaces of the router, listed in the PMPR TLV.

   # Adj.  Neigh. -  is an 8-bit unsigned integer field that specifies
      the number of adjacent neighbors.  These adjacent neighbors are
      listed first among the symmetric 1-hop MANET neighbors of all
      OSPFv3 MANET interfaces of the router in the PMPR TLV.

   # Path-MPR -  is an 8-bit unsigned integer field that specifies the
      number of MANET neighbors selected as Path-MPR.  These Path-MPRs
      are listed first among the adjacent MANET neighbors in the PMPR
      TLV.

   Reserved -  is a 6-bit field that SHOULD be cleared ('0') on
      transmission and SHOULD be ignored on reception.





RFC 5449              OSPF MPR Extension for MANET         February 2009


   U -  is a binary flag, cleared ('0') if the cost for each link from
      each advertised neighbor in the PMPR TLV and to the sending router
      is explicitly included (as shown in Figure 6), or set ('1') if a
      single metric value is included that applies to all links (as
      shown in Figure 7).

   S -  is a binary flag, cleared ('0') if the router brings up
      adjacencies only with neighbors in its MPR set and MPR-selector
      set, as per Section 5.3, or set ('1') if the router brings up
      adjacencies with all MANET neighbors as a Synch router, as per
      Section 5.6.

   Neighbor ID -  is a 32-bit field that specifies the router ID of a
      symmetric 1-hop neighbor of an OSPFv3 MANET interface of the
      router.

   Cost n -  is a 16-bit unsigned integer field that specifies the cost
      of the link in the direction from the n-th listed advertised
      neighbor in the PMPR TLV and towards this router.  A default value
      of 0xFFFF (i.e., infinity) MUST be advertised unless information
      received via Hello packets from the neighbor specifies otherwise,
      in which case the received information MUST be advertised.  If a
      neighbor is reachable via more than one interface, the cost
      advertised MUST be the minimum of the costs by which that neighbor
      can be reached.

   Padding -  is a 16-bit field that SHOULD be cleared ('0') on
      transmission and SHOULD be ignored on reception.  Padding is
      included in order that the PMPR TLV is 32-bit aligned.  Padding
      MUST be included when the TLV contains an odd number of Cost
      fields and MUST NOT be included otherwise.




















RFC 5449              OSPF MPR Extension for MANET         February 2009


     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            Type=PMPR          |           Length              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  # Sym Neigh  |  # Adj. Neigh |   # Path-MPR  | Reserved  |0|S|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Neighbor ID                         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Neighbor ID                         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    :                                                               :
    :                                                               :
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Cost 1            |            Cost 2             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    :                            .......                            :
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            Cost n-1           |            Cost n             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     Figure 6: Path-MPR TLV (PMPR) with explicit individual link costs
       (U=0) and an even number of Cost fields (hence, no padding).

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Type=PMPR             |           Length              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  # Sym Neigh  |  # Adj. Neigh |   # Path-MPR  | Reserved  |1|S|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Neighbor ID                         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Neighbor ID                         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Cost              |            Padding            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     Figure 7: Path-MPR TLV (PMPR) with a single and uniform link cost
                     (U=1) (hence, padding included).

7.  Security Considerations

   [RFC4593] describes generic threats to routing protocols, whose
   applicability to OSPFv3 [RFC5340] is not altered by the presence of
   OSPFv3 MANET interfaces.  As such, the OSPFv3 MANET interface type
   does not introduce new security threats to [RFC5340].




RFC 5449              OSPF MPR Extension for MANET         February 2009


   However, the use of a wireless medium and the lack of infrastructure,
   as enabled by the use of the OSPFv3 MANET interface type, may render
   some of the attacks described in [RFC4593] easier to undertake.

   For example, control-traffic sniffing and control-traffic analysis
   are simpler tasks with wireless than with wires, as it is sufficient
   to be somewhere within radio range in order to "listen" to wireless
   traffic.  Inconspicuous wiretapping of the right cable(s) is not
   necessary.

   In a similar fashion, physical signal interference is also a simpler
   task with wireless than with wires, as it is sufficient to emit from
   somewhere within radio range in order to be able to disrupt the
   communication medium.  No complex wire connection is required.

   Other types of interference (including not forwarding packets),
   spoofing, and different types of falsification or overloading (as
   described in [RFC4593]) are also threats to which routers using
   OSPFv3 MANET interfaces may be subject.  In these cases, the lack of
   predetermined infrastructure or authority, enabled by the use of
   OSPFv3 MANET interfaces, may facilitate such attacks by making it
   easier to forge legitimacy.

   Moreover, the consequence zone of a given threat, and its consequence
   period (as defined in [RFC4593]), may also be slightly altered over
   the wireless medium, compared to the same threat over wired networks.
   Indeed, mobility and the fact that radio range spans "further" than a
   mere cable may expand the consequence zone in some cases; meanwhile,
   the more dynamic nature of MANET topologies may decrease the
   consequence period, as harmful information (or lack of information)
   will tend to be replaced quicker by legitimate information.

8.  IANA Considerations

   This document defines three LLS TLVs, for which type values have been
   allocated from the LLS TLV type registry defined in [RFC4813].

                +------------+------------+--------------+
                |  Mnemonic  | Type Value | Name         |
                +------------+------------+--------------+
                |    FMPR    |      3     | Flooding-MPR |
                | METRIC-MPR |      4     | Metric-MPR   |
                |    PMPR    |      5     | Path-MPR     |
                +------------+------------+--------------+

                     Table 1: LLS TLV Type Assignments





RFC 5449              OSPF MPR Extension for MANET         February 2009


9.  References

9.1.  Normative References

   [RFC2119]         Bradner, S., "Key words for use in RFCs to Indicate
                     Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2328]         Moy, J., "OSPF Version 2", STD 54, RFC 2328,
                     April 1998.

   [RFC4813]         Friedman, B., Nguyen, L., Roy, A., Yeung, D., and
                     A. Zinin, "OSPF Link-Local Signaling", RFC 4813,
                     March 2007.

   [RFC5340]         Coltun, R., Ferguson, D., Moy, J., and A. Lindem,
                     "OSPF for IPv6", RFC 5340, July 2008.

9.2.  Informative References

   [MPR]             Qayyum, A., Viennot, L., and A. Laouiti,
                     "Multipoint Relaying for Flooding Broadcast
                     Messages in Mobile Wireless Networks", Proceedings
                     of HICSS , 2002.

   [MPR-analysis]    Ngyuen, D. and P. Minet, "Analysis of MPR Selection
                     in the OLSR Protocol", 2nd Int. Workshop on
                     Performance Analysis and Enhancement of
                     Wireless Networks, 2007.

   [MPR-robustness]  Adjih, C., Baccelli, E., Clausen, T., and P.
                     Jacquet, "On the Robustness and Stability of
                     Connected Dominated Sets", INRIA Research
                     Report RR-5609, 2005.

   [MPR-topology]    Baccelli, E., Clausen, T., and P. Jacquet, "Partial
                     Topology in an MPR-based Solution for Wireless OSPF
                     on Mobile Ad Hoc Networks", INRIA Research
                     Report RR-5619, 2005.

   [RFC2501]         Corson, S. and J. Macker, "Mobile Ad hoc Networking
                     (MANET): Routing Protocol Performance Issues and
                     Evaluation Considerations", RFC 2501,
                     February 1999.

   [RFC3626]         Clausen, T. and P. Jacquet, "Optimized Link State
                     Routing Protocol (OLSR)", RFC 3626, October 2003.





RFC 5449              OSPF MPR Extension for MANET         February 2009


   [RFC4593]         Barbir, A., Murphy, S., and Y. Yang, "Generic
                     Threats to Routing Protocols", RFC 4593,
                     October 2006.

   [RFC5148]         Clausen, T., Dearlove, C., and B. Adamson, "Jitter
                     Considerations in Mobile Ad Hoc Networks (MANETs)",
                     RFC 5148, February 2008.












































RFC 5449              OSPF MPR Extension for MANET         February 2009


Appendix A.  Flooding-MPR Selection Heuristic

   The following specifies a proposed heuristic for selection of
   Flooding-MPRs on interface i.  It constructs a Flooding-MPR set that
   enables a router to reach routers in the 2-hop neighborhood through
   relaying by one Flooding-MPR router.

   The following terminology will be used in describing the heuristics:
   D(Y) is the degree of a 1-hop neighbor, router Y (where Y is a member
   of N(i), defined as the number of neighbors of router Y, EXCLUDING
   all the members of N(i) and EXCLUDING the router performing the
   computation.  The proposed heuristic can then be described as
   follows.  Begin with an empty Flooding-MPR set.  Then:

   1.  Calculate D(Y), where Y is a member of N(i), for all routers in
       N(i).

   2.  Add to the Flooding-MPR set those routers in N(i) that are the
       only routers to provide reachability to a router in N2(i).  For
       example, if router B in N2(i) can be reached only through a
       router A in N(i), then add router A to the Flooding-MPR set.
       Remove the routers from N2(i) that are now covered by a router in
       the Flooding-MPR set.

   3.  While there exist routers in N2(i) that are not covered by at
       least one router in the Flooding-MPR set:

       1.  For each router in N(i), calculate the reachability, i.e.,
           the number of routers in N2(i) that are not yet covered by at
           least one router in the Flooding-MPR set, and that are
           reachable through this 1-hop neighbor;

       2.  Select as a Flooding-MPR the neighbor with the highest
           willingness among the routers in N(i) with non-zero
           reachability.  In case of a tie among routers with the same
           willingness, select the router that provides reachability to
           the maximum number of routers in N2(i).  In case of another
           tie between routers also providing the same amount of
           reachability, select as Flooding-MPR the router whose D(Y) is
           greater.  Remove the routers from N2(i) that are now covered
           by a router in the Flooding-MPR set.

   4.  As an optimization, consider in increasing order of willingness
       each router Y in the Flooding-MPR set: if all routers in N2(i)
       are still covered by at least one router in the Flooding-MPR set
       when excluding router Y, then router Y MAY be removed from the
       Flooding-MPR set.




RFC 5449              OSPF MPR Extension for MANET         February 2009


   Other algorithms, as well as improvements over this algorithm, are
   possible.  Different routers may use different algorithms
   independently.  However, the algorithm used MUST provide the router
   with a Flooding-MPR set that fulfills the flooding coverage
   criterion, i.e., it MUST select a Flooding-MPR set such that any
   2-hop neighbor is covered by at least one Flooding-MPR router.

Appendix B.  Path-MPR Selection Heuristic

   The following specifies a proposed heuristic for calculating a Path-
   MPR set that enables a router to reach routers in the 2-hop
   neighborhood through shortest paths via routers in its Path-MPR set.
   The following terminology will be used for describing this heuristic:

   A -  The router performing the Path-MPR set calculation.

   B, C, D, .... -  Other routers in the network.

   cost(A,B) -  The cost of the path through the direct link, from A to
      B.

   dist(C,A) -  The cost of the shortest path from C to A.

   A cost matrix is populated with the values of the costs of links
   originating from router A (available locally) and with values listed
   in Hello packets received from neighbor routers.  More precisely, the
   cost matrix is populated as follows:

   1.  The coefficients of the cost matrix are set by default to 0xFFFF
       (maximal value, i.e., infinity).

   2.  The coefficient cost(A,B) of the cost matrix for a link from
       router A to a neighbor B (the direct cost for this link) is set
       to the minimum cost over all interfaces that feature router B as
       a symmetric 1-hop neighbor.  The reverse cost for this link,
       cost(B,A), is set at the value received in Hello packets from
       router B.  If router B is reachable through several interfaces at
       the same time, cost(B,A) is set as the minimum cost advertised by
       router B for its links towards router A.

   3.  The coefficients of the cost matrix concerning the link between
       two neighbors of A, routers C and B, are populated at the
       reception of their Hello packets.  The cost(B,C) is set to the
       value advertised by the Hello packets from B, and, respectively,
       the cost(C,B) is set to the value advertised in Hello packets
       from C.





RFC 5449              OSPF MPR Extension for MANET         February 2009


   4.  The coefficients cost(B,C) of the cost matrix for a link that
       connects a neighbor B to a 2-hop neighbor C are obtained via the
       Hello packets received from router B.  In this case, cost(B,C)
       and cost(C,B) are respectively set to the values advertised by
       router B for the direct cost and reverse cost for node C.

   Once the cost matrix is populated, the proposed heuristic can then be
   described as follows.  Begin with an empty Path-MPR set.  Then:

   1.  Using the cost matrix and the Dijkstra algorithm, compute the
       router distance vector, i.e., the shortest distance for each pair
       (X,A) where X is in N or N2 minimizing the sum of the cost of the
       path between X and A.

   2.  Compute N' as the subset of N made of the elements X such that
       cost(X,A)=dist(X,A).

   3.  Compute N2' as the subset of N and N2 made of the elements Y that
       do not belong to N' and such that there exist X in N' such
       cost(Y,X)+cost(X,A)=dist(Y,A).

   4.  Compute the MPR selection algorithm presented in Appendix A with
       N' instead of N(i) and N2' instead of N2(i).  The resulting MPR
       set is the Path-MPR set.

   Other algorithms, as well as improvements over this algorithm, are
   possible.  Different routers may use different algorithms
   independently.  However, the algorithm used MUST provide the router
   with a Path-MPR set that fulfills the path coverage criterion, i.e.,
   it MUST select a Path-MPR set such that for any element of N or N2
   that is not in the Path-MPR set, there exists a shortest path that
   goes from this element to the router through a neighbor selected as
   Path-MPR (unless the shortest path is only one hop).

Appendix C.  Contributors

   The authors would like to thank Cedric Adjih, Acee Lindem, Padma
   Pillay-Esnault, and Laurent Viennot for their contributions to this
   document.

Appendix D.  Acknowledgments

   The authors would like to thank Juan Antonio Cordero Fuertes, Ulrich
   Herberg, and Richard Ogier for reviewing this document.







RFC 5449              OSPF MPR Extension for MANET         February 2009


Authors' Addresses

   Emmanuel Baccelli
   INRIA

   Phone: +33 1 69 33 55 11
   EMail: Emmanuel.Baccelli@inria.fr
   URI:   http://www.emmanuelbaccelli.org/


   Philippe Jacquet
   INRIA

   Phone: +33 1 3963 5263
   EMail: Philippe.Jacquet@inria.fr


   Dang-Quan Nguyen
   CRC

   Phone: +1-613-949-8216
   EMail: dang.nguyen@crc.ca


   Thomas Heide Clausen
   LIX, Ecole Polytechnique

   Phone: +33 6 6058 9349
   EMail: T.Clausen@computer.org
   URI:   http://www.thomasclausen.org/