Rfc8362
TitleOSPFv3 Link State Advertisement (LSA) Extensibility
AuthorA. Lindem, A. Roy, D. Goethals, V. Reddy Vallem, F. Baker
DateApril 2018
Format:TXT, HTML
UpdatesRFC5340, RFC5838
Status:PROPOSED STANDARD






Internet Engineering Task Force (IETF)                         A. Lindem
Request for Comments: 8362                                        A. Roy
Updates: 5340, 5838                                        Cisco Systems
Category: Standards Track                                    D. Goethals
ISSN: 2070-1721                                                    Nokia
                                                         V. Reddy Vallem

                                                                F. Baker
                                                              April 2018


          OSPFv3 Link State Advertisement (LSA) Extensibility

Abstract

   OSPFv3 requires functional extension beyond what can readily be done
   with the fixed-format Link State Advertisement (LSA) as described in
   RFC 5340.  Without LSA extension, attributes associated with OSPFv3
   links and advertised IPv6 prefixes must be advertised in separate
   LSAs and correlated to the fixed-format LSAs.  This document extends
   the LSA format by encoding the existing OSPFv3 LSA information in
   Type-Length-Value (TLV) tuples and allowing advertisement of
   additional information with additional TLVs.  Backward-compatibility
   mechanisms are also described.

   This document updates RFC 5340, "OSPF for IPv6", and RFC 5838,
   "Support of Address Families in OSPFv3", by providing TLV-based
   encodings for the base OSPFv3 unicast support and OSPFv3 address
   family support.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc8362.








RFC 8362                OSPFv3 LSA Extensibility              April 2018


Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Requirements Notation . . . . . . . . . . . . . . . . . .   4
     1.2.  OSPFv3 LSA Terminology  . . . . . . . . . . . . . . . . .   4
   2.  OSPFv3 Extended LSA Types . . . . . . . . . . . . . . . . . .   4
   3.  OSPFv3 Extended LSA TLVs  . . . . . . . . . . . . . . . . . .   5
     3.1.  Prefix Options Extensions . . . . . . . . . . . . . . . .   6
       3.1.1.  N-bit Prefix Option . . . . . . . . . . . . . . . . .   7
     3.2.  Router-Link TLV . . . . . . . . . . . . . . . . . . . . .   8
     3.3.  Attached-Routers TLV  . . . . . . . . . . . . . . . . . .   9
     3.4.  Inter-Area-Prefix TLV . . . . . . . . . . . . . . . . . .  10
     3.5.  Inter-Area-Router TLV . . . . . . . . . . . . . . . . . .  11
     3.6.  External-Prefix TLV . . . . . . . . . . . . . . . . . . .  12
     3.7.  Intra-Area-Prefix TLV . . . . . . . . . . . . . . . . . .  13
     3.8.  IPv6 Link-Local Address TLV . . . . . . . . . . . . . . .  14
     3.9.  IPv4 Link-Local Address TLV . . . . . . . . . . . . . . .  14
     3.10. IPv6-Forwarding-Address Sub-TLV . . . . . . . . . . . . .  15
     3.11. IPv4-Forwarding-Address Sub-TLV . . . . . . . . . . . . .  15
     3.12. Route-Tag Sub-TLV . . . . . . . . . . . . . . . . . . . .  16
   4.  OSPFv3 Extended LSAs  . . . . . . . . . . . . . . . . . . . .  16
     4.1.  OSPFv3 E-Router-LSA . . . . . . . . . . . . . . . . . . .  16
     4.2.  OSPFv3 E-Network-LSA  . . . . . . . . . . . . . . . . . .  18
     4.3.  OSPFv3 E-Inter-Area-Prefix-LSA  . . . . . . . . . . . . .  19
     4.4.  OSPFv3 E-Inter-Area-Router-LSA  . . . . . . . . . . . . .  20
     4.5.  OSPFv3 E-AS-External-LSA  . . . . . . . . . . . . . . . .  21
     4.6.  OSPFv3 E-NSSA-LSA . . . . . . . . . . . . . . . . . . . .  22
     4.7.  OSPFv3 E-Link-LSA . . . . . . . . . . . . . . . . . . . .  22
     4.8.  OSPFv3 E-Intra-Area-Prefix-LSA  . . . . . . . . . . . . .  24
   5.  Malformed OSPFv3 Extended LSA Handling  . . . . . . . . . . .  25
   6.  LSA Extension Backward Compatibility  . . . . . . . . . . . .  25
     6.1.  Full Extended LSA Migration . . . . . . . . . . . . . . .  25
     6.2.  Extended LSA Sparse-Mode Backward Compatibility . . . . .  26



RFC 8362                OSPFv3 LSA Extensibility              April 2018


     6.3.  LSA TLV Processing Backward Compatibility . . . . . . . .  26
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  27
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  27
     8.1.  OSPFv3 Extended LSA TLV Registry  . . . . . . . . . . . .  27
     8.2.  OSPFv3 Extended LSA Sub-TLV Registry  . . . . . . . . . .  28
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  29
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .  29
     9.2.  Informative References  . . . . . . . . . . . . . . . . .  30
   Appendix A.  Global Configuration Parameters  . . . . . . . . . .  31
   Appendix B.  Area Configuration Parameters  . . . . . . . . . . .  31
   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  32
   Contributors  . . . . . . . . . . . . . . . . . . . . . . . . . .  32
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  33

1.  Introduction

   OSPFv3 requires functional extension beyond what can readily be done
   with the fixed-format Link State Advertisement (LSA) as described in
   RFC 5340 [OSPFV3].  Without LSA extension, attributes associated with
   OSPFv3 links and advertised IPv6 prefixes must be advertised in
   separate LSAs and correlated to the fixed-format LSAs.  This document
   extends the LSA format by encoding the existing OSPFv3 LSA
   information in Type-Length-Value (TLV) tuples and allowing
   advertisement of additional information with additional TLVs.
   Backward-compatibility mechanisms are also described.

   This document updates RFC 5340, "OSPF for IPv6", and RFC 5838,
   "Support of Address Families in OSPFv3", by providing TLV-based
   encodings for the base OSPFv3 support [OSPFV3] and OSPFv3 address
   family support [OSPFV3-AF].

   A similar extension was previously proposed in support of multi-
   topology routing.  Additional requirements for the OSPFv3 LSA
   extension include source/destination routing, route tagging, and
   others.

   A final requirement is to limit the changes to OSPFv3 to those
   necessary for TLV-based LSAs.  For the most part, the semantics of
   existing OSPFv3 LSAs are retained for their TLV-based successor LSAs
   described herein.  Additionally, encoding details, e.g., the
   representation of IPv6 prefixes as described in Appendix A.4.1 in RFC
   5340 [OSPFV3], have been retained.  This requirement was included to
   increase the expedience of IETF adoption and deployment.








RFC 8362                OSPFv3 LSA Extensibility              April 2018


   The following aspects of the OSPFv3 LSA extension are described:

   1.  Extended LSA Types

   2.  Extended LSA TLVs

   3.  Extended LSA Formats

   4.  Backward Compatibility

1.1.  Requirements Notation

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

1.2.  OSPFv3 LSA Terminology

   The TLV-based OSPFv3 LSAs described in this document will be referred
   to as Extended LSAs.  The OSPFv3 fixed-format LSAs [OSPFV3] will be
   referred to as Legacy LSAs.

2.  OSPFv3 Extended LSA Types

   In order to provide backward compatibility, new LSA codes must be
   allocated.  There are eight fixed-format LSAs defined in RFC 5340
   [OSPFV3].  For ease of implementation and debugging, the LSA function
   codes are the same as the fixed-format LSAs only with 32, i.e., 0x20,
   added.  The alternative to this mapping was to allocate a bit in the
   LS Type indicating the new LSA format.  However, this would have used
   one half the LSA function code space for the migration of the eight
   original fixed-format LSAs.  For backward compatibility, the U-bit
   MUST be set in the LS Type so that the LSAs will be flooded by OSPFv3
   routers that do not understand them.















RFC 8362                OSPFv3 LSA Extensibility              April 2018


            LSA function code   LS Type   Description
            ----------------------------------------------------
            33                  0xA021    E-Router-LSA
            34                  0xA022    E-Network-LSA
            35                  0xA023    E-Inter-Area-Prefix-LSA
            36                  0xA024    E-Inter-Area-Router-LSA
            37                  0xC025    E-AS-External-LSA
            38                  N/A       Unused (Not to be allocated)
            39                  0xA027    E-Type-7-LSA
            40                  0x8028    E-Link-LSA
            41                  0xA029    E-Intra-Area-Prefix-LSA


                         OSPFv3 Extended LSA Types

3.  OSPFv3 Extended LSA TLVs

   The format of the TLVs within the body of the Extended LSAs is the
   same as the format used by the Traffic Engineering Extensions to OSPF
   [TE].  The variable TLV section consists of one or more nested TLV
   tuples.  Nested TLVs are also referred to as sub-TLVs.  The format of
   each TLV is:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              Type             |             Length            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                            Value...                           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                                TLV Format

   The Length field defines the length of the value portion in octets
   (thus, a TLV with no value portion would have a length of 0).  The
   TLV is padded to 4-octet alignment; padding is not included in the
   Length field (so a 3-octet value would have a length of 3, but the
   total size of the TLV would be 8 octets).  Nested TLVs are also
   32-bit aligned.  For example, a 1-byte value would have the Length
   field set to 1, and 3 octets of padding would be added to the end of
   the value portion of the TLV.

   This document defines the following top-level TLV types:

   o  0 - Reserved

   o  1 - Router-Link TLV




RFC 8362                OSPFv3 LSA Extensibility              April 2018


   o  2 - Attached-Routers TLV

   o  3 - Inter-Area-Prefix TLV

   o  4 - Inter-Area-Router TLV

   o  5 - External-Prefix TLV

   o  6 - Intra-Area-Prefix TLV

   o  7 - IPv6 Link-Local Address TLV

   o  8 - IPv4 Link-Local Address TLV

   Additionally, this document defines the following sub-TLV types:

   o  0 - Reserved

   o  1 - IPv6-Forwarding-Address sub-TLV

   o  2 - IPv4-Forwarding-Address sub-TLV

   o  3 - Route-Tag sub-TLV

   In general, TLVs and sub-TLVs MAY occur in any order, and the
   specification should define whether the TLV or sub-TLV is required
   and the behavior when there are multiple occurrences of the TLV or
   sub-TLV.  While this document only describes the usage of TLVs and
   sub-TLVs, sub-TLVs may be nested to any level as long as the sub-TLVs
   are fully specified in the specification for the subsuming sub-TLV.

   For backward compatibility, an LSA is not considered malformed from a
   TLV perspective unless either a required TLV is missing or a
   specified TLV is less than the minimum required length.  Refer to
   Section 6.3 for more information on TLV backward compatibility.

3.1.  Prefix Options Extensions

   The prefix options are extended from Appendix A.4.1.1 [OSPFV3].  The
   applicability of the LA-bit is expanded, and it SHOULD be set in
   Inter-Area-Prefix TLVs and MAY be set in External-Prefix TLVs when
   the advertised host IPv6 address, i.e., PrefixLength = 128 for the
   IPv6 Address Family or PrefixLength = 32 for the IPv4 Address Family
   [OSPFV3-AF], is an interface address.  In RFC 5340, the LA-bit is
   only set in Intra-Area-Prefix-LSAs (Section 4.4.3.9 of [OSPFV3]).
   This will allow a stable address to be advertised without having to
   configure a separate loopback address in every OSPFv3 area.




RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.1.1.  N-bit Prefix Option

   Additionally, the N-bit prefix option is defined.  The figure below
   shows the position of the N-bit in the prefix options (value 0x20).

                          0  1  2  3  4  5  6  7
                        +--+--+--+--+--+--+--+--+
                        |  |  | N|DN| P| x|LA|NU|
                        +--+--+--+--+--+--+--+--+

                         The Prefix Options Field

   The N-bit is set in PrefixOptions for a host address
   (PrefixLength=128 for the IPv6 Address Family or PrefixLength=32 for
   the IPv4 Address Family [OSPFV3-AF]) that identifies the advertising
   router.  While it is similar to the LA-bit, there are two
   differences.  The advertising router MAY choose NOT to set the N-bit
   even when the above conditions are met.  If the N-bit is set and the
   PrefixLength is NOT 128 for the IPv6 Address Family or 32 for the
   IPv4 Address Family [OSPFV3-AF], the N-bit MUST be ignored.
   Additionally, the N-bit is propagated in the PrefixOptions when an
   OSPFv3 Area Border Router (ABR) originates an Inter-Area-Prefix-LSA
   for an Intra-Area route that has the N-bit set in the PrefixOptions.
   Similarly, the N-bit is propagated in the PrefixOptions when an
   OSPFv3 Not-So-Stubby Area (NSSA) ABR originates an E-AS-External-LSA
   corresponding to an NSSA route as described in Section 3 of RFC 3101
   [NSSA].  The N-bit is added to the Inter-Area-Prefix TLV
   (Section 3.4), External-Prefix TLV (Section 3.6), and
   Intra-Area-Prefix-TLV (Section 3.7).  The N-bit is used as hint to
   identify the preferred address to reach the advertising OSPFv3
   router.  This would be in contrast to an anycast address
   [IPV6-ADDRESS-ARCH], which could also be a local address with the
   LA-bit set.  It is useful for applications such as identifying the
   prefixes corresponding to Node Segment Identifiers (SIDs) in Segment
   Routing [SEGMENT-ROUTING].  There may be future applications
   requiring selection of a prefix associated with an OSPFv3 router.















RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.2.  Router-Link TLV

   The Router-Link TLV defines a single router link, and the field
   definitions correspond directly to links in the OSPFv3 Router-LSA;
   see Appendix A.4.3 of [OSPFV3].  The Router-Link TLV is only
   applicable to the E-Router-LSA (Section 4.1).  Inclusion in other
   Extended LSAs MUST be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          1 (Router-Link)      |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |       0       |           Metric              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Interface ID                             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Neighbor Interface ID                       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Neighbor Router ID                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            Sub-TLVs                           .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                              Router-Link TLV
























RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.3.  Attached-Routers TLV

   The Attached-Routers TLV defines all the routers attached to an
   OSPFv3 multi-access network.  The field definitions correspond
   directly to content of the OSPFv3 Network-LSA; see Appendix A.4.4 of
   [OSPFV3].  The Attached-Routers TLV is only applicable to the
   E-Network-LSA (Section 4.2).  Inclusion in other Extended LSAs MUST
   be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |        2 (Attached-Routers)   |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              Adjacent Neighbor Router ID                      |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .              Additional Adjacent Neighbors                    .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                           Attached-Routers TLV

   There are two reasons for not having a separate TLV or sub-TLV for
   each adjacent neighbor.  The first is to discourage using the
   E-Network-LSA for more than its current role of solely advertising
   the routers attached to a multi-access network.  The router's metric
   as well as the attributes of individual attached routers should be
   advertised in their respective E-Router-LSAs.  The second reason is
   that there is only a single E-Network-LSA per multi-access link with
   the Link State ID set to the Designated Router's Interface ID, and
   consequently, compact encoding has been chosen to decrease the
   likelihood that the size of the E-Network-LSA will require IPv6
   fragmentation when advertised in an OSPFv3 Link State Update packet.

















RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.4.  Inter-Area-Prefix TLV

   The Inter-Area-Prefix TLV defines a single OSPFV3 inter-area prefix.
   The field definitions correspond directly to the content of an OSPFv3
   IPv6 Prefix, as defined in Appendix A.4.1 of [OSPFV3], and an OSPFv3
   Inter-Area-Prefix-LSA, as defined in Appendix A.4.5 of [OSPFV3].
   Additionally, the PrefixOptions are extended as described in
   Section 3.1.  The Inter-Area-Prefix TLV is only applicable to the
   E-Inter-Area-Prefix-LSA (Section 4.3).  Inclusion in other Extended
   LSAs MUST be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       3 (Inter-Area Prefix)   |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |      0        |                  Metric                       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | PrefixLength  | PrefixOptions |              0                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Address Prefix                         |
      |                             ...                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            Sub-TLVs                           .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                           Inter-Area-Prefix TLV






















RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.5.  Inter-Area-Router TLV

   The Inter-Area-Router TLV defines a single OSPFv3 Autonomous System
   Boundary Router (ASBR) that is reachable in another area.  The field
   definitions correspond directly to the content of an OSPFv3
   Inter-Area-Router-LSA, as defined in Appendix A.4.6 of [OSPFV3].  The
   Inter-Area-Router TLV is only applicable to the
   E-Inter-Area-Router-LSA (Section 4.4).  Inclusion in other Extended
   LSAs MUST be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       4 (Inter-Area Router)   |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |      0        |                Options                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |      0        |                Metric                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                 Destination Router ID                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            Sub-TLVs                           .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                           Inter-Area-Router TLV
























RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.6.  External-Prefix TLV

   The External-Prefix TLV defines a single OSPFv3 external prefix.
   With the exception of omitted fields noted below, the field
   definitions correspond directly to the content of an OSPFv3 IPv6
   Prefix, as defined in Appendix A.4.1 of [OSPFV3], and an OSPFv3
   AS-External-LSA, as defined in Appendix A.4.7 of [OSPFV3].  The
   External-Prefix TLV is only applicable to the E-AS-External-LSA
   (Section 4.5) and the E-NSSA-LSA (Section 4.6).  Additionally, the
   PrefixOptions are extended as described in Section 3.1.  Inclusion in
   other Extended LSAs MUST be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       5 (External Prefix)     |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |         |E| | |                Metric                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | PrefixLength  | PrefixOptions |              0                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Address Prefix                         |
      |                             ...                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            Sub-TLVs                           .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                            External-Prefix TLV

   In the External-Prefix TLV, the optional IPv6/IPv4 Forwarding Address
   and External Route Tag are now sub-TLVs.  Given the Referenced LS
   Type and Referenced Link State ID from the AS-External-LSA have never
   been used or even specified, they have been omitted from the
   External-Prefix TLV.  If there were ever a requirement for a
   referenced LSA, it could be satisfied with a sub-TLV.

   The following sub-TLVs are defined for optional inclusion in the
   External-Prefix TLV:

   o  1 - IPv6-Forwarding-Address sub-TLV (Section 3.10)

   o  2 - IPv4-Forwarding-Address sub-TLV (Section 3.11)

   o  3 - Route-Tag sub-TLV (Section 3.12)





RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.7.  Intra-Area-Prefix TLV

   The Intra-Area-Prefix TLV defines a single OSPFv3 intra-area prefix.
   The field definitions correspond directly to the content of an OSPFv3
   IPv6 Prefix, as defined in Appendix A.4.1 of [OSPFV3], and an OSPFv3
   Link-LSA, as defined in Appendix A.4.9 of [OSPFV3].  The
   Intra-Area-Prefix TLV is only applicable to the E-Link-LSA
   (Section 4.7) and the E-Intra-Area-Prefix-LSA (Section 4.8).
   Additionally, the PrefixOptions are extended as described in
   Section 3.1.  Inclusion in other Extended LSAs MUST be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       6 (Intra-Area Prefix)   |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |      0        |                  Metric                       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | PrefixLength  | PrefixOptions |              0                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Address Prefix                         |
      |                             ...                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            Sub-TLVs                           .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                           Intra-Area-Prefix TLV






















RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.8.  IPv6 Link-Local Address TLV

   The IPv6 Link-Local Address TLV is to be used with IPv6 address
   families as defined in [OSPFV3-AF].  The IPv6 Link-Local Address TLV
   is only applicable to the E-Link-LSA (Section 4.7).  Inclusion in
   other Extended LSAs MUST be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  7 (IPv6 Local-Local Address) |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-                                                             -+
      |                                                               |
      +-            IPv6 Link-Local Interface Address                -+
      |                                                               |
      +-                                                             -+
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            Sub-TLVs                           .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                        IPv6 Link-Local Address TLV

3.9.  IPv4 Link-Local Address TLV

   The IPv4 Link-Local Address TLV is to be used with IPv4 address
   families as defined in [OSPFV3-AF].  The IPv4 Link-Local Address TLV
   is only applicable to the E-Link-LSA (Section 4.7).  Inclusion in
   other Extended LSAs MUST be ignored.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  8 (IPv4 Local-Local Address) |       TLV Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |             IPv4 Link-Local Interface Address                 |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            Sub-TLVs                           .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                        IPv4 Link-Local Address TLV




RFC 8362                OSPFv3 LSA Extensibility              April 2018


3.10.  IPv6-Forwarding-Address Sub-TLV

   The IPv6-Forwarding-Address TLV has identical semantics to the
   optional forwarding address in Appendix A.4.7 of [OSPFV3].  The IPv6-
   Forwarding-Address TLV is applicable to the External-Prefix TLV
   (Section 3.6).  Specification as a sub-TLV of other TLVs is not
   defined herein.  The sub-TLV is optional and the first specified
   instance is used as the forwarding address as defined in [OSPFV3].
   Instances subsequent to the first MUST be ignored.

   The IPv6-Forwarding-Address TLV is to be used with IPv6 address
   families as defined in [OSPFV3-AF].  It MUST be ignored for other
   address families.  The IPv6-Forwarding-Address TLV length must meet a
   minimum length (16 octets), or it will be considered malformed as
   described in Section 6.3.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       1 - Forwarding Address  |          sub-TLV Length       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-                                                             -+
      |                                                               |
      +-                    Forwarding Address                       -+
      |                                                               |
      +-                                                             -+
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                        IPv6-Forwarding-Address TLV

3.11.  IPv4-Forwarding-Address Sub-TLV

   The IPv4-Forwarding-Address TLV has identical semantics to the
   optional forwarding address in Appendix A.4.7 of [OSPFV3].  The
   IPv4-Forwarding-Address TLV is applicable to the External-Prefix TLV
   (Section 3.6).  Specification as a sub-TLV of other TLVs is not
   defined herein.  The sub-TLV is optional, and the first specified
   instance is used as the forwarding address as defined in [OSPFV3].
   Instances subsequent to the first MUST be ignored.

   The IPv4-Forwarding-Address TLV is to be used with IPv4 address
   families as defined in [OSPFV3-AF].  It MUST be ignored for other
   address families.  The IPv4-Forwarding-Address TLV length must meet a
   minimum length (4 octets), or it will be considered malformed as
   described in Section 6.3.




RFC 8362                OSPFv3 LSA Extensibility              April 2018


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       2 - Forwarding Address  |          sub-TLV Length       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     Forwarding Address                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                        IPv4-Forwarding-Address TLV

3.12.  Route-Tag Sub-TLV

   The optional Route-Tag sub-TLV has identical semantics to the
   optional External Route Tag in Appendix A.4.7 of [OSPFV3].  The
   Route-Tag sub-TLV is applicable to the External-Prefix TLV
   (Section 3.6).  Specification as a sub-TLV of other TLVs is not
   defined herein.  The sub-TLV is optional, and the first specified
   instance is used as the Route Tag as defined in [OSPFV3].  Instances
   subsequent to the first MUST be ignored.

   The Route-Tag TLV length must meet a minimum length (4 octets), or it
   will be considered malformed as described in Section 6.3.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       3 - Route Tag           |          sub-TLV Length       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          Route Tag                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                             Route-Tag Sub-TLV

4.  OSPFv3 Extended LSAs

   This section specifies the OSPFv3 Extended LSA formats and encoding.
   The Extended OSPFv3 LSAs corresponded directly to the original OSPFv3
   LSAs specified in [OSPFV3].

4.1.  OSPFv3 E-Router-LSA

   The E-Router-LSA has an LS Type of 0xA021 and has the same base
   information content as the Router-LSA defined in Appendix A.4.3 of
   [OSPFV3].  However, unlike the existing Router-LSA, it is fully
   extensible and represented as TLVs.






RFC 8362                OSPFv3 LSA Extensibility              April 2018


       0                    1                   2                   3
       0 1 2 3  4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |           LS Age               |1|0|1|         0x21            |
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       Link State ID                            |
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Advertising Router                          |
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    LS Sequence Number                          |
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |        LS Checksum             |            Length             |
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  0  |Nt|x|V|E|B|            Options                            |
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                                .
      .                            TLVs                                .
      .                                                                .
      +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                            Extended Router-LSA

   Other than having a different LS Type, all LSA Header fields are the
   same as defined for the Router-LSA.  Initially, only the top-level
   Router-Link TLV (Section 3.2) is applicable, and an E-Router-LSA may
   include multiple Router-Link TLVs.  Like the existing Router-LSA, the
   LSA length is used to determine the end of the LSA including any
   TLVs.  Depending on the implementation, it is perfectly valid for an
   E-Router-LSA to not contain any Router-Link TLVs.  However, this
   would imply that the OSPFv3 router doesn't have any adjacencies in
   the corresponding area and is forming an adjacency or adjacencies
   over an unnumbered link(s).  Note that no E-Router-LSA stub link is
   advertised for an unnumbered link.


















RFC 8362                OSPFv3 LSA Extensibility              April 2018


4.2.  OSPFv3 E-Network-LSA

   The E-Network-LSA has an LS Type of 0xA022 and has the same base
   information content as the Network-LSA defined in Appendix A.4.4 of
   [OSPFV3].  However, unlike the existing Network-LSA, it is fully
   extensible and represented as TLVs.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          LS Age               |1|0|1|         0x22            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Link State ID                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Advertising Router                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   LS Sequence Number                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       LS Checksum             |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       0       |            Options                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                           TLVs                                .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                               E-Network-LSA

   Other than having a different LS Type, all LSA Header fields are the
   same as defined for the Network-LSA.  Like the existing Network-LSA,
   the LSA length is used to determine the end of the LSA including any
   TLVs.  Initially, only the top-level Attached-Routers TLV
   (Section 3.3) is applicable.  If the Attached-Router TLV is not
   included in the E-Network-LSA, it is treated as malformed as
   described in Section 5.  Instances of the Attached-Router TLV
   subsequent to the first MUST be ignored.














RFC 8362                OSPFv3 LSA Extensibility              April 2018


4.3.  OSPFv3 E-Inter-Area-Prefix-LSA

   The E-Inter-Area-Prefix-LSA has an LS Type of 0xA023 and has the same
   base information content as the Inter-Area-Prefix-LSA defined in
   Appendix A.4.5 of [OSPFV3].  However, unlike the existing
   Inter-Area-Prefix-LSA, it is fully extensible and represented as
   TLVs.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          LS Age               |1|0|1|         0x23            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Link State ID                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Advertising Router                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   LS Sequence Number                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       LS Checksum             |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                           TLVs                                .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                          E-Inter-Area-Prefix-LSA

   Other than having a different LS Type, all LSA Header fields are the
   same as defined for the Inter-Area-Prefix-LSA.  In order to retain
   compatibility and semantics with the current OSPFv3 specification,
   each Inter-Area-Prefix LSA MUST contain a single Inter-Area-Prefix
   TLV.  This will facilitate migration and avoid changes to functions
   such as incremental Shortest Path First (SPF) computation.

   Like the existing Inter-Area-Prefix-LSA, the LSA length is used to
   determine the end of the LSA including any TLVs.  Initially, only the
   top-level Inter-Area-Prefix TLV (Section 3.4) is applicable.  If the
   Inter-Area-Prefix TLV is not included in the E-Inter-Area-Prefix-LSA,
   it is treated as malformed as described in Section 5.  Instances of
   the Inter-Area-Prefix TLV subsequent to the first MUST be ignored.










RFC 8362                OSPFv3 LSA Extensibility              April 2018


4.4.  OSPFv3 E-Inter-Area-Router-LSA

   The E-Inter-Area-Router-LSA has an LS Type of 0xA024 and has the same
   base information content as the Inter-Area-Router-LSA defined in
   Appendix A.4.6 of [OSPFV3].  However, unlike the
   Inter-Area-Router-LSA, it is fully extensible and represented as
   TLVs.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          LS Age               |1|0|1|         0x24            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Link State ID                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Advertising Router                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   LS Sequence Number                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       LS Checksum             |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                           TLVs                                .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                          E-Inter-Area-Router-LSA

   Other than having a different LS Type, all LSA Header fields are the
   same as defined for the Inter-Area-Router-LSA.  In order to retain
   compatibility and semantics with the current OSPFv3 specification,
   each Inter-Area-Router-LSA MUST contain a single Inter-Area-Router
   TLV.  This will facilitate migration and avoid changes to functions
   such as incremental SPF computation.

   Like the existing Inter-Area-Router-LSA, the LSA length is used to
   determine the end of the LSA including any TLVs.  Initially, only the
   top-level Inter-Area-Router TLV (Section 3.5) is applicable.  If the
   Inter-Area-Router TLV is not included in the E-Inter-Area-Router-LSA,
   it is treated as malformed as described in Section 5.  Instances of
   the Inter-Area-Router TLV subsequent to the first MUST be ignored.










RFC 8362                OSPFv3 LSA Extensibility              April 2018


4.5.  OSPFv3 E-AS-External-LSA

   The E-AS-External-LSA has an LS Type of 0xC025 and has the same base
   information content as the AS-External-LSA defined in Appendix A.4.7
   of [OSPFV3].  However, unlike the existing AS-External-LSA, it is
   fully extensible and represented as TLVs.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          LS Age               |1|1|0|         0x25            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Link State ID                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Advertising Router                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   LS Sequence Number                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       LS Checksum             |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                           TLVs                                .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                             E-AS-External-LSA

   Other than having a different LS Type, all LSA Header fields are the
   same as defined for the AS-External-LSA.  In order to retain
   compatibility and semantics with the current OSPFv3 specification,
   each LSA MUST contain a single External-Prefix TLV.  This will
   facilitate migration and avoid changes to OSPFv3 functions such as
   incremental SPF computation.

   Like the existing AS-External-LSA, the LSA length is used to
   determine the end of the LSA including any TLVs.  Initially, only the
   top-level External-Prefix TLV (Section 3.6) is applicable.  If the
   External-Prefix TLV is not included in the E-External-AS-LSA, it is
   treated as malformed as described in Section 5.  Instances of the
   External-Prefix TLV subsequent to the first MUST be ignored.











RFC 8362                OSPFv3 LSA Extensibility              April 2018


4.6.  OSPFv3 E-NSSA-LSA

   The E-NSSA-LSA will have the same format and TLVs as the Extended
   AS-External-LSA (Section 4.5).  This is the same relationship that
   exists between the NSSA-LSA, as defined in Appendix A.4.8 of
   [OSPFV3], and the AS-External-LSA.  The NSSA-LSA will have type
   0xA027, which implies area flooding scope.  Future requirements may
   dictate that supported TLVs differ between the E-AS-External-LSA and
   the E-NSSA-LSA.  However, future requirements are beyond the scope of
   this document.

4.7.  OSPFv3 E-Link-LSA

   The E-Link-LSA has an LS Type of 0x8028 and will have the same base
   information content as the Link-LSA defined in Appendix A.4.9 of
   [OSPFV3].  However, unlike the existing Link-LSA, it is fully
   extensible and represented as TLVs.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          LS Age               |1|0|0|         0x28            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Link State ID                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Advertising Router                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   LS Sequence Number                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       LS Checksum             |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Rtr Priority  |                Options                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                           TLVs                                .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                                E-Link-LSA

   Other than having a different LS Type, all LSA Header fields are the
   same as defined for the Link-LSA.

   Only the Intra-Area-Prefix TLV (Section 3.7), IPv6 Link-Local Address
   TLV (Section 3.8), and IPv4 Link-Local Address TLV (Section 3.9) are
   applicable to the E-Link-LSA.  Like the Link-LSA, the E-Link-LSA





RFC 8362                OSPFv3 LSA Extensibility              April 2018


   affords advertisement of multiple intra-area prefixes.  Hence,
   multiple Intra-Area-Prefix TLVs (Section 3.7) may be specified, and
   the LSA length defines the end of the LSA including any TLVs.

   A single instance of the IPv6 Link-Local Address TLV (Section 3.8)
   SHOULD be included in the E-Link-LSA.  Instances following the first
   MUST be ignored.  For IPv4 address families as defined in
   [OSPFV3-AF], this TLV MUST be ignored.

   Similarly, only a single instance of the IPv4 Link-Local Address TLV
   (Section 3.9) SHOULD be included in the E-Link-LSA.  Instances
   following the first MUST be ignored.  For OSPFv3 IPv6 address
   families as defined in [OSPFV3-AF], this TLV SHOULD be ignored.

   If the IPv4/IPv6 Link-Local Address TLV corresponding to the OSPFv3
   Address Family is not included in the E-Link-LSA, it is treated as
   malformed as described in Section 5.

   Future specifications may support advertisement of routing and
   topology information for multiple address families.  However, this is
   beyond the scope of this document.






























RFC 8362                OSPFv3 LSA Extensibility              April 2018


4.8.  OSPFv3 E-Intra-Area-Prefix-LSA

   The E-Intra-Area-Prefix-LSA has an LS Type of 0xA029 and has the same
   base information content as the Intra-Area-Prefix-LSA defined in
   Appendix A.4.10 of [OSPFV3] except for the Referenced LS Type.
   However, unlike the Intra-Area-Prefix-LSA, it is fully extensible and
   represented as TLVs.  The Referenced LS Type MUST be either an
   E-Router-LSA (0xA021) or an E-Network-LSA (0xA022).

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |           LS Age              |1|0|1|         0x29            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Link State ID                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Advertising Router                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   LS Sequence Number                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |        LS Checksum            |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       0                       |     Referenced LS Type        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                  Referenced Link State ID                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |               Referenced Advertising Router                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      .                                                               .
      .                            TLVs                               .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                          E-Intra-Area-Prefix-LSA

   Other than having a different LS Type, all LSA Header fields are the
   same as defined for the Intra-Area-Prefix-LSA.

   Like the Intra-Area-Prefix-LSA, the E-Intra-Area-Link-LSA affords
   advertisement of multiple intra-area prefixes.  Hence, multiple
   Intra-Area-Prefix TLVs may be specified, and the LSA length defines
   the end of the LSA including any TLVs.









RFC 8362                OSPFv3 LSA Extensibility              April 2018


5.  Malformed OSPFv3 Extended LSA Handling

   Extended LSAs that have inconsistent length or other encoding errors,
   as described herein, MUST NOT be installed in the Link State
   Database, acknowledged, or flooded.  Reception of malformed LSAs
   SHOULD be counted and/or logged for examination by the administrator
   of the OSPFv3 routing domain.  Note that for the purposes of length
   validation, a TLV or sub-TLV should not be considered invalid unless
   the length exceeds the length of the LSA or does not meet the minimum
   length requirements for the TLV or sub-TLV.  This allows for sub-TLVs
   to be added as described in Section 6.3.

   Additionally, an LSA MUST be considered malformed if it does not
   include all of the required TLVs and sub-TLVs.

6.  LSA Extension Backward Compatibility

   In the context of this document, backward compatibility is solely
   related to the capability of an OSPFv3 router to receive, process,
   and originate the TLV-based LSAs defined herein.  Unrecognized TLVs
   and sub-TLVs are ignored.  Backward compatibility for future OSPFv3
   extensions utilizing the TLV-based LSAs is out of scope and must be
   covered in the documents describing those extensions.  Both full and,
   if applicable, partial deployment SHOULD be specified for future TLV-
   based OSPFv3 LSA extensions.

6.1.  Full Extended LSA Migration

   If ExtendedLSASupport is enabled (Appendix A), OSPFv3 Extended LSAs
   will be originated and used for the SPF computation.  Individual OSPF
   Areas can be migrated separately with the Legacy AS-External-LSAs
   being originated and used for the SPF computation.  This is
   accomplished by enabling AreaExtendedLSASupport (Appendix B).

   An OSPFv3 routing domain or area may be non-disruptively migrated
   using separate OSPFv3 instances for the Extended LSAs.  Initially,
   the OSPFv3 instances with ExtendedLSASupport will have a lower
   preference, i.e., higher administrative distance, than the OSPFv3
   instances originating and using the Legacy LSAs.  Once the routing
   domain or area is fully migrated and the OSPFv3 Routing Information
   Bases (RIBs) have been verified, the OSPFv3 instances using the
   Extended LSAs can be given preference.  When this has been completed
   and the routing within the OSPF routing domain or area has been
   verified, the original OSPFv3 instance using Legacy LSAs can be
   removed.






RFC 8362                OSPFv3 LSA Extensibility              April 2018


6.2.  Extended LSA Sparse-Mode Backward Compatibility

   In this mode, OSPFv3 will use the Legacy LSAs for the SPF computation
   and will only originate Extended LSAs when LSA origination is
   required in support of additional functionality.  Furthermore, those
   Extended LSAs will only include the top-level TLVs (e.g., Router-Link
   TLVs or Inter-Area TLVs), which are required for that new
   functionality.  However, if a top-level TLV is advertised, it MUST
   include required sub-TLVs, or it will be considered malformed as
   described in Section 5.  Hence, this mode of compatibility is known
   as "sparse-mode".  The advantage of sparse-mode is that functionality
   utilizing the OSPFv3 Extended LSAs can be added to an existing OSPFv3
   routing domain without the requirement for migration.  In essence,
   this compatibility mode is very much like the approach taken for
   OSPFv2 [OSPF-PREFIX-LINK].  As with all the compatibility modes,
   backward compatibility for the functions utilizing the Extended LSAs
   must be described in the IETF documents describing those functions.

6.3.  LSA TLV Processing Backward Compatibility

   This section defines the general rules for processing LSA TLVs.  To
   ensure compatibility of future TLV-based LSA extensions, all
   implementations MUST adhere to these rules:

   1.  Unrecognized TLVs and sub-TLVs are ignored when parsing or
       processing Extended LSAs.

   2.  Whether or not partial deployment of a given TLV is supported
       MUST be specified.

   3.  If partial deployment is not supported, mechanisms to ensure the
       corresponding feature is not deployed MUST be specified in the
       document defining the new TLV or sub-TLV.

   4.  If partial deployment is supported, backward compatibility and
       partial deployment MUST be specified in the document defining the
       new TLV or sub-TLV.

   5.  If a TLV or sub-TLV is recognized but the length is less than the
       minimum, then the LSA should be considered malformed, and it
       SHOULD NOT be acknowledged.  Additionally, the occurrence SHOULD
       be logged with enough information to identify the LSA by type,
       Link State ID, originator, and sequence number and identify the
       TLV or sub-TLV in error.  Ideally, the log entry would include
       the hexadecimal or binary representation of the LSA including the
       malformed TLV or sub-TLV.





RFC 8362                OSPFv3 LSA Extensibility              April 2018


   6.  Documents specifying future TLVs or Sub-TLVs MUST specify the
       requirements for usage of those TLVs or sub-TLVs.

   7.  Future TLVs or sub-TLVs must be optional.  However, there may be
       requirements for sub-TLVs if an optional TLV is specified.

7.  Security Considerations

   In general, extensible OSPFv3 LSAs are subject to the same security
   concerns as those described in RFC 5340 [OSPFV3].  Additionally,
   implementations must assure that malformed TLV and sub-TLV
   permutations do not result in errors that cause hard OSPFv3 failures.

   If there were ever a requirement to digitally sign OSPFv3 LSAs as
   described for OSPFv2 LSAs in RFC 2154 [OSPF-DIGITAL-SIGNATURE], the
   mechanisms described herein would greatly simplify the extension.

8.  IANA Considerations

   This specification defines nine OSPFv3 Extended LSA types as
   described in Section 2.  These have been added to the existing OSPFv3
   LSA Function Codes registry.

   The specification defines a code point for the N-bit in the OSPFv3
   Prefix-Options registry.  The value 0x20 has been assigned.

   This specification also creates two registries for OSPFv3 Extended
   LSA TLVs and sub-TLVs.  The TLV and sub-TLV code points in these
   registries are common to all Extended LSAs, and their respective
   definitions must define where they are applicable.

8.1.  OSPFv3 Extended LSA TLV Registry

   The "OSPFv3 Extended LSA TLVs" registry defines top-level TLVs for
   Extended LSAs and has been placed in the existing OSPFv3 IANA
   registry.

   Nine values have been allocated:

   o  0 - Reserved

   o  1 - Router-Link TLV

   o  2 - Attached-Routers TLV

   o  3 - Inter-Area-Prefix TLV

   o  4 - Inter-Area-Router TLV



RFC 8362                OSPFv3 LSA Extensibility              April 2018


   o  5 - External-Prefix TLV

   o  6 - Intra-Area-Prefix TLV

   o  7 - IPv6 Link-Local Address TLV

   o  8 - IPv4 Link-Local Address TLV

   Types in the range 9-32767 are allocated via IETF Review or IESG
   Approval [RFC8126].

   Types in the range 32768-33023 are Reserved for Experimental Use;
   these will not be registered with IANA and MUST NOT be mentioned by
   RFCs.

   Types in the range 33024-45055 are to be assigned on a First Come
   First Served (FCFS) basis.

   Types in the range 45056-65535 are not to be assigned at this time.
   Before any assignments can be made in the 33024-65535 range, there
   MUST be an IETF specification that specifies IANA Considerations that
   cover the range being assigned.

8.2.  OSPFv3 Extended LSA Sub-TLV Registry

   The "OSPFv3 Extended LSA Sub-TLVs" registry defines sub-TLVs at any
   level of nesting for Extended LSAs and has been placed in the
   existing OSPFv3 IANA registry.

   Four values have been allocated:

   o  0 - Reserved

   o  1 - IPv6-Forwarding-Address sub-TLV

   o  2 - IPv4-Forwarding-Address sub-TLV

   o  3 - Route-Tag sub-TLV

   Types in the range 4-32767 are allocated via IETF Review or IESG
   Approval.

   Types in the range 32768-33023 are Reserved for Experimental Use;
   these will not be registered with IANA and MUST NOT be mentioned by
   RFCs.

   Types in the range 33024-45055 are to be assigned on an FCFS basis.




RFC 8362                OSPFv3 LSA Extensibility              April 2018


   Types in the range 45056-65535 are not to be assigned at this time.
   Before any assignments can be made in the 33024-65535 range, there
   MUST be an IETF specification that specifies IANA Considerations that
   cover the range being assigned.

9.  References

9.1.  Normative References

   [NSSA]     Murphy, P., "The OSPF Not-So-Stubby Area (NSSA) Option",
              RFC 3101, DOI 10.17487/RFC3101, January 2003,
              <https://www.rfc-editor.org/info/rfc3101>.

   [OSPFV3]   Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
              for IPv6", RFC 5340, DOI 10.17487/RFC5340, July 2008,
              <https://www.rfc-editor.org/info/rfc5340>.

   [OSPFV3-AF]
              Lindem, A., Ed., Mirtorabi, S., Roy, A., Barnes, M., and
              R. Aggarwal, "Support of Address Families in OSPFv3",
              RFC 5838, DOI 10.17487/RFC5838, April 2010,
              <https://www.rfc-editor.org/info/rfc5838>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [TE]       Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering
              (TE) Extensions to OSPF Version 2", RFC 3630,
              DOI 10.17487/RFC3630, September 2003,
              <https://www.rfc-editor.org/info/rfc3630>.










RFC 8362                OSPFv3 LSA Extensibility              April 2018


9.2.  Informative References

   [IPV6-ADDRESS-ARCH]
              Hinden, R. and S. Deering, "IP Version 6 Addressing
              Architecture", RFC 4291, DOI 10.17487/RFC4291, February
              2006, <https://www.rfc-editor.org/info/rfc4291>.

   [MT-OSPFV3]
              Mirtorabi, S. and A. Roy, "Multi-topology routing in
              OSPFv3 (MT-OSPFv3)", Work in Progress, draft-ietf-ospf-mt-
              ospfv3-03, July 2007.

   [OSPF-DIGITAL-SIGNATURE]
              Murphy, S., Badger, M., and B. Wellington, "OSPF with
              Digital Signatures", RFC 2154, DOI 10.17487/RFC2154, June
              1997, <https://www.rfc-editor.org/info/rfc2154>.

   [OSPF-PREFIX-LINK]
              Psenak, P., Gredler, H., Shakir, R., Henderickx, W.,
              Tantsura, J., and A. Lindem, "OSPFv2 Prefix/Link Attribute
              Advertisement", RFC 7684, DOI 10.17487/RFC7684, November
              2015, <https://www.rfc-editor.org/info/rfc7684>.

   [SEGMENT-ROUTING]
              Psenak, P., Previdi, S., Filsfils, C., Gredler, H.,
              Shakir, R., Henderickx, W., and J. Tantsura, "OSPFv3
              Extensions for Segment Routing", Work in Progress,
              draft-ietf-ospf-ospfv3-segment-routing-extensions-11,
              January 2018.






















RFC 8362                OSPFv3 LSA Extensibility              April 2018


Appendix A.  Global Configuration Parameters

   The global configurable parameter ExtendedLSASupport is added to the
   OSPFv3 protocol.  If ExtendedLSASupport is enabled, the OSPFv3 router
   will originate OSPFv3 Extended LSAs and use the LSAs for the SPF
   computation.  If ExtendedLSASupport is not enabled, a subset of
   OSPFv3 Extended LSAs may still be originated and used for other
   functions as described in Section 6.2.

Appendix B.  Area Configuration Parameters

   The area configurable parameter AreaExtendedLSASupport is added to
   the OSPFv3 protocol.  If AreaExtendedLSASupport is enabled, the
   OSPFv3 router will originate link and area OSPFv3 Extended LSAs and
   use the LSAs for the SPF computation.  Legacy AS-Scoped LSAs will
   still be originated and used for the AS-External-LSA computation.  If
   AreaExtendedLSASupport is not enabled, a subset of OSPFv3 link and
   area Extended LSAs may still be originated and used for other
   functions as described in Section 6.2.

   For regular areas, i.e., areas where AS-scoped LSAs are flooded,
   disabling AreaExtendedLSASupport for a regular OSPFv3 area (not a
   Stub or NSSA area) when ExtendedLSASupport is enabled is
   contradictory and SHOULD be prohibited by implementations.



























RFC 8362                OSPFv3 LSA Extensibility              April 2018


Acknowledgments

   OSPFv3 TLV-based LSAs were first proposed in "Multi-topology routing
   in OSPFv3 (MT-OSPFv3)" [MT-OSPFV3].

   Thanks for Peter Psenak for significant contributions to the
   backward-compatibility mechanisms.

   Thanks go to Michael Barnes, Mike Dubrovsky, Anton Smirnov, and Tony
   Przygienda for review of the draft versions and discussions of
   backward compatibility.

   Thanks to Alan Davey for review and comments including the suggestion
   to separate the Extended LSA TLV definitions from the Extended LSAs
   definitions.

   Thanks to David Lamparter for review and suggestions on backward
   compatibility.

   Thanks to Karsten Thomann, Chris Bowers, Meng Zhang, and Nagendra
   Kumar for review and editorial comments.

   Thanks to Alia Atlas for substantive Routing Area Director (AD)
   comments prior to IETF last call.

   Thanks to Alvaro Retana and Suresh Krishnan for substantive comments
   during IESG Review.

   Thanks to Mehmet Ersue for the Operations and Management (OPS)
   Directorate review.

Contributors

   Sina Mirtorabi
   Cisco Systems
   170 Tasman Drive
   San Jose, CA  95134
   United States of America

   Email: sina@cisco.com











RFC 8362                OSPFv3 LSA Extensibility              April 2018


Authors' Addresses

   Acee Lindem
   Cisco Systems
   301 Midenhall Way
   Cary, NC  27513
   United States of America

   Email: acee@cisco.com


   Abhay Roy
   Cisco Systems
   170 Tasman Drive
   San Jose, CA  95134
   United States of America

   Email: akr@cisco.com


   Dirk Goethals
   Nokia
   Copernicuslaan 50
   Antwerp 2018
   Belgium

   Email: dirk.goethals@nokia.com


   Veerendranatha Reddy Vallem
   Bangalore
   India

   Email: vallem.veerendra@gmail.com


   Fred Baker
   Santa Barbara, California  93117
   United States of America

   Email: FredBaker.IETF@gmail.com